Never stop challenging your limitations. If you want to dig out your potentials, just keep trying. Repeated attempts will sharpen your minds. Maybe our NSEI_OTS_AR-7.6 study materials are suitable for you. We strongly advise you to have a brave attempt. You will own a wonderful experience after you learning our NSEI_OTS_AR-7.6 Study Materials. Our study materials are different from common study materials, which can motivate you to concentrate on study.
| Section | Objectives |
|---|---|
| Topic 1: Asset management | - Explain OT standard and Fortinet compliance - Fortinet Security Fabric for an OT network - Implement device detection on FortiGate and FortiNAC |
| Topic 2: Network security | - Configure security inspections for industrial protocols - Configure virtual patching - Configure automation |
| Topic 3: Monitoring and risk assessment | - Analyze security reports from FortiAnalyzer - Create FortiAnalyzer event handlers - Perform risk assessment and management |
| Topic 4: Network access control | - Explain OT Ethernet concepts - Configure network segmentation schemas - Configure network access authentication |
>> Fortinet NSEI_OTS_AR-7.6 Study Test <<
Have you been many years at your position but haven't got a promotion? Or are you a new comer in your company and eager to make yourself outstanding? Our NSEI_OTS_AR-7.6 exam materials can help you. After a few days' studying and practicing with our NSEI_OTS_AR-7.6 products you will easily pass the examination. God helps those who help themselves. If you choose our NSEI_OTS_AR-7.6 Study Materials, you will find God just by your side. The only thing you have to do is just to make your choice and study. Isn't it very easy? So know more about our NSEI_OTS_AR-7.6 study guide right now!
NEW QUESTION # 32
Refer to the exhibit.
A Logical Topology page of a FortiGate device is shown. Your OT company wants to gain visibility into the network. You decide to implement device detection with the Security Fabric. Based on the exhibit, which statement is correct? (Choose one answer)
Answer: A
Explanation:
The correct answer is A. Device Detection is enabled on the other identified device .
The study guide explains that device identification is a "useful feature for the Security Fabric topology view" and that "FortiGate detects most third-party devices in your network and adds them to the topology view of the Security Fabric." It also states that in the interfaces section, you can enable device detection , and this detection is what allows FortiGate to identify devices based on observed traffic.
In the exhibit, the tooltip distinguishes between "1 device requires authorization" and "1 other identified device." That means the unauthorized device is a separate FortiGate/Fabric member issue, while the other identified device is simply a detected third-party device shown in the topology because device detection is working. Therefore, the correct interpretation is that device detection is enabled for that identified device.
Option B is incorrect because the exhibit does not say the other identified device requires authorization.
Option C is not supported by the study guide, and option D is too specific because no evidence in the exhibit confirms that the detection was enabled specifically on port3 .
NEW QUESTION # 33
Refer to the exhibit.
A partial OT network is shown. You have configured the FortiGate device with VLANs to segment the OT network. The supervisor now wants to connect to the PLC from the Engineering Workstation. How can you allow access from the Engineering Workstation to the PLC? (Choose one answer)
Answer: B
Explanation:
The correct answer is D. You must configure a layer 3 switch .
The study guide explains that "Layer 2 devices can add or remove tags" but "cannot modify them." It then states that "A layer 3 device, such as a router or FortiGate, can modify the VLAN tag before routing the packet. This allows them to route traffic between VLANs." It also explicitly describes
"Router on a Stick" as "a way to allow routing between VLANs." Since the exhibit shows a layer-2 switch and the Engineering Workstation and PLC are placed in different VLANs, inter-VLAN communication requires layer-3 routing.
The other options do not solve this requirement. intra-switch-policy explicit/implicit applies to a software switch , where member interfaces are in the same broadcast domain and same subnet, not to routing between separate VLANs. forward domain IDs are used in transparent mode to confine broadcasts to specific broadcast domains; they do not provide inter-VLAN access. Therefore, to let the Engineering Workstation in one VLAN reach the PLC in another VLAN, you need a layer 3 routing function , which matches option D .
NEW QUESTION # 34
As the first step in your OT network protection plan, you must identify the OT protocols that the FortiGate device supports. Which two configurations must you implement on this FortiGate device? (Choose two answers)
Answer: B,D
Explanation:
The correct answers are B and C . The study guide states that "You can use application control signatures to detect OT protocols" and that "Application control detects the protocols used in applications like Modbus, IEC 104, and the contents of the telecontrol messages" . It also shows that a Modbus application control profile can be enabled on a firewall policy "for OT protocol visibility in the monitor status." This directly supports B , because application control is the feature used to identify and monitor OT protocols on FortiGate.
The guide also explains under IPS that "By default, OT signatures are excluded from the signatures lists on the GUI until you enable them on the CLI" using config ips global and set exclude-signatures none .
Once enabled, FortiGate can use those OT signatures for OT-aware inspection and protection. That supports C as the second required configuration. A is related to device discovery, not protocol identification, and D is focused on exploit and vulnerability detection rather than the first-step goal of identifying OT protocols.
NEW QUESTION # 35
You want to improve access control for your large OT network using passive authentication. What must you configure on FortiGate? (Choose one answer)
Answer: C
Explanation:
The correct answer is A. Fortinet Single-Sign On (FSSO) . The study guide states under Active and Passive Authentication that for passive authentication, "User does not receive a login prompt from FortiGate" ,
"Credentials are determined automatically" , and specifically "FSSO, RSSO, and NTLM can be used." It then explains that passive authentication occurs with the single sign-on method and explicitly identifies Fortinet SSO (FSSO) as one of those methods.
The guide also says: "For passive authentication, you can implement FSSO. FSSO allows users who have already authenticated on the network through another system to be transparently identified. After initial login to any system on the network, users can access allowed resources without being prompted for credentials." That is exactly what the question asks for: improving access control in a large OT network using passive authentication .
The other options do not match passive authentication. Local users are part of local authentication, two- factor authentication adds an extra security factor but still uses active authentication, and FortiAuthenticator as a remote server supports centralized authentication for mid-to-large networks, but by itself it is not the specific passive-authentication method being asked here. The study guide is explicit that the FortiGate configuration for passive authentication is FSSO .
NEW QUESTION # 36
Refer to the exhibit.
An industrial Ethernet protocol skipping layers 3 to 6 is shown. Which industrial Ethernet protocol is it?
(Choose one answer)
Answer: B
Explanation:
The correct answer is D. EtherCAT . The study guide explicitly states under the Ethernet/IP and EtherCAT section that "EtherCAT is a protocol that offers real-time communication in a primary-secondary configuration" and "EtherCAT skips layers 3 to 6 to deliver real-time communication." It also adds that
"the most important feature of this protocol is that secondary devices collect only the information they need from the data packets." This matches the exhibit exactly, where the diagram shows Real-Time Data above a Proprietary MAC and Proprietary physical layer , reflecting the protocol structure that bypasses the intermediate OSI layers.
The other options do not match this behavior. The guide says POWERLINK uses layer 2 and layer 7 of the OSI model, not that it skips layers 3 to 6. It also explains that Ethernet/IP is the industrial protocol based entirely on Ethernet standards and adapts to the OSI model. Modbus is described as an open client/server protocol and is not suitable for transmitting data in real time . Therefore, the protocol in the exhibit is clearly EtherCAT .
NEW QUESTION # 37
......
Advancement in NSEI_OTS_AR-7.6 information and communications technology generates huge potential for moving business and production up the value-chain, and improving the quality of life of citizens. And there is no doubt that you can get all kinds of information in cyber space now, NSEI_OTS_AR-7.6 Latest Torrent is not an exception. I strongly recommend the study materials compiled by our company for you, the advantages of our NSEI_OTS_AR-7.6 exam questions are too many to enumerate; I will just list three of them for your reference.
Reliable NSEI_OTS_AR-7.6 Braindumps Ebook: https://www.braindumpstudy.com/NSEI_OTS_AR-7.6_braindumps.html