ExamPassdump의 API인증 API-SIEE덤프를 구매하여 공부한지 일주일만에 바로 시험을 보았는데 고득점으로 시험을 패스했습니다.이는ExamPassdump의 API인증 API-SIEE덤프를 구매한 분이 전해온 희소식입니다. 다른 자료 필요없이 단지 저희API인증 API-SIEE덤프로 이렇게 어려운 시험을 일주일만에 패스하고 자격증을 취득할수 있습니다.덤프가격도 다른 사이트보다 만만하여 부담없이 덤프마련이 가능합니다.구매전 무료샘플을 다운받아 보시면 믿음을 느낄것입니다.
| 주제 | 소개 |
|---|---|
| 주제 1 |
|
| 주제 2 |
|
| 주제 3 |
|
| 주제 4 |
|
| 주제 5 |
|
API-SIEE인증시험은API사의 인중시험입니다.API인증사의 시험을 패스한다면 it업계에서의 대우는 달라집니다. 때문에 점점 많은 분들이API인증API-SIEE시험을 응시합니다.하지만 실질적으로API-SIEE시험을 패스하시는 분들은 너무 적습니다.전분적인 지식을 터득하면서 완벽한 준비하고 응시하기에는 너무 많은 시간이 필요합니다.하지만 우리ExamPassdump는 이러한 여러분의 시간을 절약해드립니다.
질문 # 69
Which of the following tools is used for inspection of coating?
정답：B
설명：
The correct answer isAbecause the most common and direct inspection instrument used for acoating after applicationis thedry film thickness DFT gauge. In source inspection and quality surveillance, coating verification typically includes checking whether the applied paint or protective coating has achieved the specified thickness range. That is a fundamental acceptance point because coating that is too thin may fail prematurely, while coating that is too thick may crack, blister, or cure improperly. In practical inspection language, the option says "Dry film thickness DFT," but it clearly refers to theDFT measuring gauge/toolused by inspectors.
The other options are related but not the best answer. Adigital surface profile gaugeandsurface profile replica tapeare mainly used to evaluate thesurface profile of blasted steel before coating, not the final dry coating thickness itself. Anultrasonic thickness meteris generally used for base material wall thickness measurement, not routine paint-coating inspection. The API guide covers source inspection and surveillance of manufacturing activities and stresses verification against specifications, records, and inspection points for covered equipment.
질문 # 70
According to ANSI/NETA/ATS, when performing a dielectric withstand test on each bus section, the test voltage shall be applied for how long?
정답：A
설명：
The correct answer isB. UnderANSI/NETA/ATSpractices, adielectric withstand teston eachbus sectionis typically performed by applying the specified test voltage forone minute. This one-minute duration is the standard acceptance interval used to demonstrate that the bus insulation system can safely withstand the prescribed overvoltage without breakdown, flashover, or unacceptable leakage. It provides enough time to reveal insulation weakness while remaining within the intended non-routine high-potential test method for acceptance testing.
From a source inspection perspective, this matters because switchgear bus insulation integrity is a critical verification point during factory testing and final quality surveillance. The inspector is expected to confirm that the correct test method, voltage level, duration, and acceptance criteria are used and properly recorded in the manufacturer's test documentation. The API Guide for Source Inspection and Quality Surveillance of Electrical Equipment includesswitchgearsamong the major covered equipment categories and emphasizes verification of tests, records, and compliance with applicable standards during source inspection and surveillance. Therefore, for a dielectric withstand test on each bus section, the specified voltage is applied forone minute, makingoption Bthe verified answer.
질문 # 71
Areas where ignitable concentrations of flammable gases or vapors are present continuously or for long periods of time are classified as:
정답：D
설명：
The correct answer isA, Class I Zone 0. In hazardous-area classification,Class Irefers to locations whereflammable gases or vaporsmay be present in the atmosphere. Under theZone system,Zone 0is the classification used where an ignitable concentration is presentcontinuously,for long periods, orfrequently enoughthat it must be assumed to exist during normal conditions. This is the most severe gas-vapor zone classification because the hazardous atmosphere is expected to be present as part of normal operation.
By contrast,Class I Zone 1applies where flammable gas or vapor is likely to be present in normal operation, but not continuously for long periods.Class I Zone 2applies where the hazardous atmosphere is not likely in normal operation and, if it does occur, it exists only for a short time.Class I Division 2is also a less severe classification under the Division system, not the continuous-presence category.
From an API source inspection perspective, correct hazardous-area classification is critical because it governs the acceptable protection methods, enclosure types, markings, and certification requirements for electrical equipment installed in those areas.
질문 # 72
As part of a purchase order, what type of documents typically supplement industry standards?
정답：A
설명：
The correct answer isDbecause, in source inspection and procurement practice,client standardsare commonly included in or referenced by thepurchase orderto supplement generalindustry standards. Industry standards such as API, IEEE, NEMA, IEC, and NFPA establish broad technical requirements, but they often do not capture all of the purchaser's project-specific expectations. Client standards fill that gap by adding requirements for materials, testing, documentation, preservation, coating, marking, data submission, inspection hold points, and deviations or concessions.
This is a key concept in API-aligned source inspection. The source inspector does not verify equipment only against generic published standards. The inspector must verify conformance to thepurchase order, project specifications, approved drawings, applicable codes and standards, and purchaser-specific requirements. In that framework, client standards are a normal supplement to industry standards. The other options are less appropriate.Supplier quality standardsandmanufacturing standardsare usually internal vendor documents, whilematerial test reportsare records of compliance, not governing standards. Therefore, the documents that typically supplement industry standards as part of a purchase order areclient standards, makingoption Dthe verified answer.
질문 # 73
Which enclosure type is defined in the guide as a construction where free exchange of air is prevented between the inside and outside of the motor?
정답：C
질문 # 74
......
ExamPassdump선택으로API API-SIEE시험을 패스하도록 도와드리겠습니다. 우선 우리ExamPassdump 사이트에서API API-SIEE관련자료의 일부 문제와 답 등 샘플을 제공함으로 여러분은 무료로 다운받아 체험해보실 수 있습니다. 체험 후 우리의ExamPassdump에 신뢰감을 느끼게 됩니다. ExamPassdump에서 제공하는API API-SIEE덤프로 시험 준비하세요. 만약 시험에서 떨어진다면 덤프전액환불을 약속 드립니다.
API-SIEE퍼펙트 덤프데모문제: https://www.exampassdump.com/API-SIEE_valid-braindumps.html