Those who are ambitious to obtain NSE7_FSN_AR-7.6 certification mainly include office workers; they expect to reach a higher position and get handsome salary, moreover, a prosperous future. All of these requirements our NSE7_FSN_AR-7.6 exam materials can meet. Our NSE7_FSN_AR-7.6 study materials can help you pass the exam successful. Before you decide to buy our NSE7_FSN_AR-7.6 Exam Torrent, you can free download the demo of our NSE7_FSN_AR-7.6 exam questions, which contains a few of questions and answers of our NSE7_FSN_AR-7.6 training guide.
| Section | Objectives |
|---|---|
| SD-WAN | - Performance SLA - SD-WAN architecture - Deployment and troubleshooting - Overlay VPN - Application steering - SD-WAN routing |
| Enterprise Firewall | - Security Fabric integration - Advanced firewall deployment - Authentication and identity - High availability - Centralized management and analytics - VPN technologies - Routing and advanced networking - Troubleshooting |
>> Training NSE7_FSN_AR-7.6 Pdf <<
What is Dumpkiller Fortinet NSE7_FSN_AR-7.6 exam training materials? There are many online sites provide Fortinet NSE7_FSN_AR-7.6 exam training resources. But Dumpkiller provide you the most actual information. Dumpkiller have professional personnel of certification experts, technical staff, and comprehensive language masters. They are always studying the latest Fortinet NSE7_FSN_AR-7.6 Exam. Therefore, if you want to pass the Fortinet NSE7_FSN_AR-7.6 examination, please Login Dumpkiller website. It will let you close to your success, and into your dream paradise step by step.
NEW QUESTION # 135
You configure the overlay tunnels for an SD-WAN hub-and-spoke topology defined with IPsec tunnels, BGP on loopback, and dynamic BGP.
Which two are recommended IPsec settings for this topology? (Choose two answers.)
Answer: A,C
Explanation:
The SD-WAN 7.6 Enterprise Administrator Study Guide identifies the recommended BGP-on-loopback IPsec settings. For branches, it specifies:
"Static tunnel type (remote end IP address is known)."
"net-device enable."
Enabling net-device on the spoke creates a kernel interface for the tunnel. This assists with tunnel monitoring and management and is required to support ADVPN shortcut tunnels. Dynamic BGP establishes on-demand BGP peerings between spokes after an ADVPN shortcut is created; therefore, the spoke must support those dynamic shortcut interfaces. This makes option C correct.
The spoke should also configure localid. The FortiOS 7.6 Administrator Study Guide explains: "Local ID: if the peer accepts a specific peer ID, type that same peer ID in this field." The local ID supplies the spoke's IKE identity to the dial-up hub, allowing the hub to identify and authenticate the connecting spoke correctly.
Therefore, option D is correct.
Option A reverses the recommended roles. The hub must use a dynamic tunnel type because it operates as the dial-up server and does not require every spoke's changing public gateway address in advance.
Option B is also incorrect. The guide states: "There is no need to configure any tunnel IP address, so the IKE Mode Config is not used." BGP on loopback uses the loopback address and exchange-interface-ip instead of IKE mode configuration.
References: SD-WAN 7.6 Enterprise Administrator Study Guide, SD-WAN Overlay Design and Best Practices, pages 118-119 and 122; FortiOS 7.6 Administrator Study Guide, IPsec VPN - Phase 1 Network Settings, page 375; FortiOS 7.6 - BGP on loopback.
NEW QUESTION # 136
Refer to the exhibit.
The network diagram shows the addition of Site 2 with an overlapping network segment to the existing IPsec VPN connection between the hub and Site 1.
Which IPsec phase 2 configuration must you make on the FortiGate hub to enable equal-cost multipath (ECMP) routing when multiple remote sites connect with overlapping subnets?
Answer: C
Explanation:
Comprehensive and Detailed 100 to 150 words of Explanation From Secure Networking Architect Study Guides topics:
Fortinet documents three values for the phase 2 route-overlap setting: use-new, use-old, and allow. The required value for simultaneous VPNs advertising overlapping remote subnets is allow.
With route-overlap allow, FortiGate keeps the existing dial-up VPN active and also accepts the newly connected VPN. The Enterprise Firewall 7.6 Administrator Study Guide explicitly states that traffic from the central FortiGate is then load-balanced using equal-cost multipath across both VPNs. This directly satisfies the scenario and makes C correct.
The default use-new setting disconnects the existing VPN and accepts the new one, while use-old keeps the existing VPN and rejects the new connection. Neither produces ECMP. multipath enable and net-device ecmp are not the phase 2 commands FortiOS uses to permit overlapping dial-up VPN routes.
NEW QUESTION # 137
Refer to the exhibit, which shows the output of the command get router info bgp neighbors 100.64.2.254 advertised-routes.
What can you conclude from the output?
Answer: D
NEW QUESTION # 138
Refer to the exhibit.
A partial output of diagnose npu up6 port-list on FortiGate 2000E is shown.
An administrator is unable to analyze traffic flowing between port1 and port17 using the diagnose sniffer command.
Which two commands allow the administrator to view the traffic? (Choose two.)
Answer: A,C
Explanation:
The administrator cannot see traffic in the sniffer because it is being offloaded to the NPU (NP6). To view the traffic, offloading must be disabled so packets pass through the CPU.
B). config firewall policy ... set auto-asic-offload disable: This is the recommended method to troubleshoot specific traffic. By disabling ASIC offloading in the relevant firewall policies (Policies 5 and 17 in the exhibit), traffic is forced to the CPU and becomes visible to the sniffer.
C). diagnose npu np6 fastpath disable 1: This command temporarily disables the fastpath processing on the specific NP6 processor (ID 1) handling the ports. This forces all traffic handled by that NPU to the CPU, allowing the sniffer to capture it.
Incorrect Options: Option A uses invalid syntax (port-list disable is not a valid command). Option D (config system npu) is not the standard method for granular troubleshooting.
NEW QUESTION # 139
Refer to the exhibit.
Partial output of the get vpn ipsec tunnel details command is shown. Based on the output, which two statements are correct? (Choose two.)
Answer: C,D
Explanation:
The correct answers are C and D.
The study guide's get vpn ipsec tunnel details example shows:
replay: enabled
inbound and outbound sections with separate SPIs
NPU acceleration: encryption(outbound) decryption(inbound)and it labels these as "Phase 2 SAs for each direction" and "Hardware acceleration" This directly proves D. Anti-replay is enabled, because the output explicitly says replay: enabled For the NPU status, the study guide explains the exact npu_flag meanings:
npu_flag=00 = both IPsec SAs loaded to the kernel
npu_flag=01 = outbound IPsec SA copied to NPU
npu_flag=02 = inbound IPsec SA copied to NPU
npu_flag=03 = both outbound and inbound IPsec SAs copied to NPU
Because the exhibit shows hardware acceleration in both directions - encryption(outbound) and decryption (inbound) - the matching npu_flag is 03, not 02. That makes C correct and A incorrect.
Why B is wrong:
The same study guide output labels the tunnel as having Phase 2 SAs for each direction, so different inbound and outbound SPIs are normal for the two SAs. Also, the FortiOS administration guide explains that auto- negotiate controls whether phase 2 SA negotiation is initiated automatically, not whether inbound and outbound SPIs are different: "By default the phase 2 security association (SA) is not negotiated until a peer attempts to send data... Auto-negotiate initiates the phase 2 SA negotiation automatically..." So the verified answers are: C, D.
NEW QUESTION # 140
......
At Dumpkiller, we are proud to offer you actual NSE7_FSN_AR-7.6 exam questions in our Fortinet NSE7_FSN_AR-7.6 practice exam material. This actual study material has been checked and approved by leading professionals in the field. A team of over 90,000 experts and professionals have collaborated to design the Fortinet NSE 7 - Secure Networking 7.6 Architect (NSE7_FSN_AR-7.6) exam material, ensuring that you receive both theoretical knowledge and practical insights to excel in the Fortinet NSE 7 - Secure Networking 7.6 Architect exam.
NSE7_FSN_AR-7.6 Reliable Test Testking: https://www.dumpkiller.com/NSE7_FSN_AR-7.6_braindumps.html