참고: Pass4Test에서 Google Drive로 공유하는 무료, 최신 HPE6-A85 시험 문제집이 있습니다: https://drive.google.com/open?id=1X32gU_3gLxF9s-uv4rtCt22ycKxOuuca
HP인증 HPE6-A85시험은 IT인증자격증중 가장 인기있는 자격증을 취득하는 필수시험 과목입니다. HP인증 HPE6-A85시험을 패스해야만 자격증 취득이 가능합니다. Pass4Test의HP인증 HPE6-A85는 최신 시험문제 커버율이 높아 시험패스가 아주 간단합니다. HP인증 HPE6-A85덤프만 공부하시면 아무런 우려없이 시험 보셔도 됩니다. 시험합격하면 좋은 소식 전해주세요.
HPE6-A85 시험은 Aruba Wireless Technologies와 함께 일한 경험이 있고 경력을 발전시키기 위해 지식과 기술을 검증하는 데 관심이있는 IT 전문가를위한 것입니다. 이 시험은 캠퍼스 환경에서 Aruba 무선 네트워크를 작성하고 관리 할 책임이있는 네트워크 관리자, 엔지니어 및 기술자에게도 적합합니다.
HP HPE6-A85 (Aruba Campus Access Associate) 인증 시험은 네트워크 엔지니어링 및 관리 분야의 경력을 추구하는 데 관심이있는 개인의 기술과 지식을 평가하도록 설계되었습니다. 이 인증 시험은 유선, 무선 및 원격 액세스를 포함한 Aruba Campus Access Networking Technologies에 대한 후보자의 이해를 테스트하도록 설계되었습니다. HPE6-A85 시험을 성공적으로 통과하는 것은 네트워크 엔지니어링에 대한 전문 지식을 보여주고 오늘날의 경쟁 업무 시장에서 귀중한 자산이 될 수있는 좋은 방법입니다.
HP 인증 HPE6-A85시험대비덤프를 찾고 계시다면Pass4Test가 제일 좋은 선택입니다.저희Pass4Test에서는 여라가지 IT자격증시험에 대비하여 모든 과목의 시험대비 자료를 발췌하였습니다. Pass4Test에서 시험대비덤프자료를 구입하시면 시험불합격시 덤프비용환불신청이 가능하고 덤프 1년 무료 업데이트서비스도 가능합니다. Pass4Test를 선택하시면 후회하지 않을것입니다.
HP HPE6-A85 자격증을 취득하면 IT 전문가가 취업 시장에서 두드러지게 나타날 수 있고, 경력을 발전시킬 수 있습니다. 이 자격증은 오늘날 기업 환경에서 높은 수요를 누리는 Aruba 무선 네트워크를 배포하고 관리하는 능력을 후보자가 인증합니다. 또한 이 자격증은 후보자가 IT 분야에서 전문적인 개발과 지속적인 학습에 헌신하는 것을 입증할 수 있습니다.
질문 # 119
What is the correct command to add a static route to a class-c-network 10.2.10.0 via a gateway of 172.16.1.1?
정답：B
설명：
The correct command to add a static route to a class-c-network 10.2.10.0 via a gateway of 172.16.1.1 is ip- route 10.2.10.0/24 172.16.1.1 . This command specifies the destination network address (10.2.10.0) and prefix length (/24) and the next-hop address (172.16.1 .1) for reaching that network from the switch. The other commands are either incorrect syntax or incorrect parameters for adding a static route.References:https://www.
arubanetworks.com/techdocs/AOS-CX_10_04/NOSCG/Content/cx-noscg/ip-routing/static-routes.htm To add a static route in network devices, including Aruba switches, the correct command format generally includes the destination network, subnet mask (or CIDR notation for the mask), and the next-hop IP address.
The command "ip route 10.2.10.0/24 172.16.1.1" correctly specifies the destination network "10.2.10.0" with a class C subnet mask indicated by "/24", and "172.16.1.1" as the next-hop IP address. This command is succinct and follows the standard syntax for adding a static route in many network operating systems, including ArubaOS-CX. The other options either have incorrect syntax or include additional unnecessary parameters that are not typically part of the standard command to add a static route.
질문 # 120
You are configuring a network with a stacked pair of 6300M switches used for distribution and layer 3 services. You create a new VLAN for users that will be used on multiple access stacks of CX6200 switches connected downstream of the distribution stack You will be creating multiple VLANs/subnets similar to this will be utilized in multiple access stacks What is the correct way to configure the routable interface for the subnet to be associated with this VLAN?
정답：B
설명：
Explanation
The correct way to configure the routable interface for the subnet to be associated with this VLAN is to create an SVI Switched Virtual Interface (SVI) Switched Virtual Interface (SVI) is a virtual interface on a switch that represents a VLAN and provides Layer 3 routing functions for that VLAN . SVIs are used to enable inter-VLAN routing , provide gateway addresses for hosts in VLANs , apply ACLs or QoS policies to VLANs
, etc . SVIs have some advantages over physical routed interfaces such as saving interface ports , reducing cable costs , simplifying network design , etc . SVIs are usually numbered according to their VLAN IDs (e.g., vlan 10) and assigned IP addresses within the subnet of their VLANs . SVIs can be created and configured by using commands such as interface vlan , ip address , no shutdown , etc . SVIs can be verified by using commands such as show ip interface brief , show vlan , show ip route , etc . in the subnet on the 6300M stack.
An SVI is a virtual interface on a switch that represents a VLAN and provides Layer 3 routing functions for that VLAN. Creating an SVI in the subnet on the 6300M stack allows the switch to act as a gateway for the users in that VLAN and enable inter-VLAN routing between different subnets. Creating an SVI in the subnet on the 6300M stack also simplifies network design and management by reducing the number of physical interfaces and cables required for routing.
The other options are not correct ways to configure the routable interface for the subnet to be associated with this VLAN because:
Create a physically routed interface in the subnet on the 6300M stack for each downstream switch: This option is incorrect because creating a physically routedinterface in the subnet on the 6300M stack for each downstream switch would require using one physical port and cable per downstream switch, which would consume interface resources and increase cable costs. Creating a physically routed interface in the subnet on the 6300M stack for each downstream switch would also complicate network design and management by requiring separate routing configurations and policies for each interface.
Create an SVl in the subnet on each downstream switch: This option is incorrect because creating an SVI in the subnet on each downstream switch would not enable inter-VLAN routing between different subnets, as each downstream switch would act as a gateway for its own VLAN only. Creating an SVI in the subnet on each downstream switch would also create duplicate IP addresses in the same subnet, which would cause IP conflicts and routing errors.
Create an SVl in the subnet on the 6300M stack, and assign the management address of each downstream switch stack to a different IP address in the same subnet: This option is incorrect because creating an SVI in the subnet on the 6300M stack, and assigning the management address of each downstream switch stack to a different IP address in the same subnet would not enable inter-VLAN routing between different subnets, as each downstream switch would still act as a gateway for its own VLAN only. Creating an SVI in the subnet on the 6300M stack, and assigning the management address of each downstream switch stack to a different IP address in the same subnet would also create unnecessary IP addresses in the same subnet, which would waste IP space and complicate network management.
References: https://www.arubanetworks.com/techdocs/AOS-CX/10.05/HTML/5200-7295/index.html
https://www.arubanetworks.com/techdocs/AOS-CX/10.05/HTML/5200-7295/cx-noscg/l3-routing/l3-routing-ove
https://www.arubanetworks.com/techdocs/AOS-CX/10.05/HTML/5200-7295/cx-noscg/l3-routing/l3-routing-con
질문 # 121
What is indicated by a flashing amber global status indicator LED on an Aruba CX6200M?
정답：C
설명：
A flashing amber global status indicator LED on an Aruba CX6200M switch typically indicates that the switch has encountered a fault, but it is recoverable. This LED behavior serves as an alert to the network administrator that an issue needs to be addressed, but it does not necessarily mean that the switch is inoperable.
질문 # 122
A network technician at a branch office is connecting VolP phones to a newly configured AOS-CX switch. Users are complaining that voice quality is not as good as at the corporate office. Further investigation shows the local-priority value at the branch office is 1 while at the corporate office is
5.
What describes the issue regarding the default QoS behavior on the AOS-CX switch?
정답：B
설명：
In an AOS-CX switch, if the QoS trust mode is not configured, it is set to none by default. The VoIP phones will mark their traffic with a local-priority value, which, if the QoS trust mode is none, will correspond to CoS map entry 1 by default. The local-priority value of 1 at the branch office likely indicates that the traffic is not being prioritized correctly compared to the corporate office, where a local-priority of 5 suggests a higher level of prioritization for voice traffic.
질문 # 123
Which device configuration group types can a user define in Aruba Central during group creation?
(Select two.)
정답：C,E
설명：
In Aruba Central during group creation, users can define various configuration groups to manage settings for multiple devices. A Security group allows you to apply consistent security settings across devices, and a Template group enables you to apply pre-defined configurations to devices. These groups help streamline the deployment and management of network devices in Aruba Central.
질문 # 124
......
HPE6-A85 Dumps: https://www.pass4test.net/HPE6-A85.html
그리고 Pass4Test HPE6-A85 시험 문제집의 전체 버전을 클라우드 저장소에서 다운로드할 수 있습니다: https://drive.google.com/open?id=1X32gU_3gLxF9s-uv4rtCt22ycKxOuuca