商品を購入するとき、信頼できる会社を選ぶことができます。我々CertShikenはInternational Code Councilの93-Tall-Mass-Timber-Buildings試験の最高の通過率を保証してInternational Code Councilの93-Tall-Mass-Timber-Buildingsソフトの無料のデモと一年間の無料更新を承諾します。あなたに安心させるために、我々はあなたがInternational Code Councilの93-Tall-Mass-Timber-Buildings試験に失敗したら全額で返金するのを保証します。CertShikenはあなたのInternational Code Councilの93-Tall-Mass-Timber-Buildings試験を準備する間あなたの最もよい友達です。
| Section | Objectives |
|---|---|
| Tall Mass Timber Building Code Provisions | - Mass Timber Products and Definitions - Structural and Connection Requirements
|
>> 93-Tall-Mass-Timber-Buildingsテスト模擬問題集 <<
93-Tall-Mass-Timber-Buildings試験に問題なく迅速に合格する方法 答えは、有効で優れた93-Tall-Mass-Timber-Buildingsトレーニングガイドにあります。 既に93-Tall-Mass-Timber-Buildingsトレーニング資料を用意しています。 これらは、保証対象のプロの93-Tall-Mass-Timber-Buildings実践資料です。 参考のために許容できる価格に加えて、3つのバージョンのすべての93-Tall-Mass-Timber-Buildings試験資料は、10年以上にわたってこの分野の専門家によって編集されています。
質問 # 37
For Type IV-A, IV-B, and IV-C construction, each of the following materials on the exterior side of mass timber exterior walls is required to be noncombustible except:
正解：C
解説：
The code provides a specific combustible-material exception for qualifying water-resistive barriers , making option D correct. The exterior-protection provisions for Types IV-A, IV-B, and IV-C require the exterior side of mass timber walls to receive noncombustible protection with at least a 40-minute assigned protection time, and components of the exterior wall covering are generally required to be noncombustible.
A water-resistive barrier may be combustible only where it satisfies stringent fire-performance criteria.
Among those criteria, the 2021 IBC limits peak heat-release rate and total heat release under ASTM E1354 and establishes flame-spread and smoke-developed limits under ASTM E84 or UL 723. The provision therefore does not create a blanket exemption for arbitrary combustible membranes.
Insulation, exterior cladding, and architectural components forming part of the regulated exterior wall covering must comply with the applicable noncombustibility requirements unless some other express code allowance applies. The WRB is the specifically identified exception tested by this question.
During inspection, product identification and fire-test documentation should be checked rather than assuming that a membrane qualifies merely because it is marketed as a water-resistive barrier.
References/Topics: 2021 IBC Sections 602.4.1.1, 602.4.2.1 and 602.4.3.1; exterior wall protection and qualifying water-resistive barriers.
質問 # 38
Each of the following is true regarding the fire-resistance rating for exterior bearing walls except:
正解：A
解説：
Option A is the exception because the base fire-resistance rating for an exterior bearing wall in Type IV-C construction is two hours, not one hour. The values are established by 2021 IBC Table 601.
Type IV-A has the most stringent tall mass timber construction requirements and assigns a three-hour rating to exterior bearing walls. Type IV-B and Type IV-C each assign a two-hour rating. Consequently, options B, C, and D accurately state the Table 601 requirements, while option A understates the required rating by one hour.
The Table 601 value is the minimum construction-type rating. Exterior bearing walls must also comply with the exterior-wall requirements of Table 705.5 based on fire separation distance. Where another code provision requires a higher rating, the more restrictive requirement governs. The inspector must therefore avoid treating the two-hour Type IV-C value as an absolute maximum.
Field verification should include the approved wall assembly, mass timber dimensions, noncombustible exterior protection, membrane continuity, protection of connections, intersections, joints, and any required opening protection. An exterior bearing wall installed as a nominal one-hour assembly would not comply merely because the timber itself has substantial cross-sectional dimensions.
References/Topics: 2021 IBC Table 601; Sections 602.4 and 705.5; exterior bearing-wall ratings for Types IV- A, IV-B, and IV-C.
質問 # 39
Refer to the exhibit by clicking on the EXHIBIT button above.
In the detail shown, if the connections between the glulam beam and CLT panels all require a fire-resistance rating of one (1) hour and the wood cover is designed per AWC Technical Report 10 to provide the entire 1 hour of protection, what is the minimum thickness and number of layers required for the locations shown in red?
正解：C
解説：
Two layers of 5/8-inch Type X gypsum wallboard are required for the condition shown, so option D is correct. The relevant AWC TR10 connection-protection methodology distinguishes between outer gypsum layers and the base layer immediately adjacent to the connection .
For 5/8-inch Type X gypsum board, an outer layer contributes 40 minutes. However, when gypsum board is being relied upon as the complete thermal-separation protection for a connection, TR10 reduces the contribution of the final/base layer to 50 percent. Therefore, the base layer contributes 20 minutes , while the second, exterior layer contributes 40 minutes . The total is:
20 minutes + 40 minutes = 60 minutes .
That satisfies the one-hour required protection period.
This is why simply looking at the normal 40-minute contribution of one 5/8-inch Type X layer would be incorrect for this connection condition. TR10 expressly uses the reduced base-layer contribution when gypsum constitutes the connection protection. The same methodology shows that four 5/8-inch Type X layers are needed for 120 minutes: 20 + 40 + 40 + 40 = 140 minutes, satisfying two hours.
References/Topics: AWC Technical Report No. 10, Sections 4.4.2 and connection-protection examples. TR10 states that outer 5/8-inch Type X layers provide 40 minutes each while the base layer provides 20 minutes.
質問 # 40
Which of the following is an acceptable alternative for protecting structural connections from fire in Type IV- A, IV-B or IV-C construction?
正解：B
解説：
Option D directly reflects the engineering-analysis method authorized by 2021 IBC Section 2304.10.1. For structural connections in Type IV-A, IV-B, or IV-C construction, the analysis must demonstrate that temperatures at every relevant portion of the connection remain within prescribed limits for a period corresponding to the fire-resistance rating required of the connected structural element.
The code establishes two critical temperature-rise limits: an average rise of not more than 250°F and a maximum rise of not more than 325°F . For this purpose, the "connection" includes the connectors, fasteners, and those portions of the wood members that participate structurally in the connection.
Option A is incorrect because ASTM E136 is a test for determining whether a material is noncombustible; it is not the fire-resistance test method for a structural connection. Option B is not a code-recognized substitute for the required connection fire evaluation. Option C is insufficient because a manufacturer's generalized fire- performance representation does not establish the required code fire-resistance duration unless supported through an approved test, evaluation, or engineering analysis.
References/Topics: 2021 IBC Section 2304.10.1; engineering-analysis method for Type IV-A, IV-B, and IV- C structural connections.
質問 # 41
When Type X gypsum board is used as noncombustible protection over mass timber on the building ' s exterior walls, which of the following fasteners are permitted?
正解：D
解説：
Option A reproduces one of the two permitted exterior gypsum-board fastening methods in 2021 IBC Section
722.7.2.2. Type X gypsum board used as noncombustible protection on the exterior side of mass timber walls may be attached using galvanized nails of minimum 12 gage with a 7/16-inch head and sufficient length to penetrate the mass timber at least 1 inch .
The code also permits ASTM C1002 Type S, W, or G screws, but those screws must likewise penetrate the mass timber a minimum of 1 inch . Options C and D are therefore incorrect because they specify only 3/4- inch and 7/8-inch penetration, respectively. Option B is incorrect because it substitutes 16-gage nails for the minimum 12-gage requirement.
Section 722.7.2.2 additionally requires exterior Type X gypsum-board layers to be fastened 12 inches on center each way and 6 inches on center at joints or ends. Panel-edge fasteners must be located at least 1 inch and not more than 2 inches from the edge.
These fastening details are part of the conditions necessary to claim the protection contribution in Table
722.7.1(2).
References/Topics: 2021 IBC Sections 722.7.1 and 722.7.2.2; exterior Type X gypsum-board protection.
質問 # 42
......
93-Tall-Mass-Timber-Buildings prepトレントは、PDF、ソフト、およびAPPバージョンの3つのバージョンをお客様に提供します。それぞれに独自の利点があります。次に、93-Tall-Mass-Timber-Buildingsテスト問題集のPDFバージョンを紹介します。 PDFバージョンが非常に便利で実用的であることはよく知られています。 93-Tall-Mass-Timber-Buildingsテストブレイン問題集のPDFバージョンは、お客様にデモを提供します。同時に、PDFバージョンを使用している場合は、PDFバージョンごとに93-Tall-Mass-Timber-Buildings試験トレントを印刷できます。メモを取るのはとても簡単です。私たちの93-Tall-Mass-Timber-Buildingsテストブレイン問題集はあなたに大きな利便性をもたらすと信じています。
93-Tall-Mass-Timber-Buildings日本語資格取得: https://www.certshiken.com/93-Tall-Mass-Timber-Buildings-shiken.html