We are amenable to offer help by introducing our NSEI_OTS_AR-7.6 real exam materials and they can help you pass the Fortinet NSE I - OT Security 7.6 Architect practice exam efficiently. All knowledge is based on the real exam by the help of experts. By compiling the most important points of questions into our NSEI_OTS_AR-7.6 guide prep our experts also amplify some difficult and important points. Being devoted to this area for over ten years, our experts keep the excellency of our Fortinet NSE I - OT Security 7.6 Architect exam question like always. They are distinguished experts in this area who can beef up your personal capacity. By cutting through the clutter of tremendous knowledge, they picked up the essence into our NSEI_OTS_AR-7.6 Guide prep.
| Section | Weight | Objectives |
|---|---|---|
| Topic 1: Asset Management | 25% | - Device detection and inventory using FortiGate & FortiNAC - OT security standards and compliance (IEC 62443, NIST) - Fortinet Security Fabric for OT environments |
| Topic 2: Network Security | 25% | - Deep inspection for industrial protocols (Modbus, DNP3, OPC) - Security automation and threat response - Virtual patching for legacy OT systems |
| Topic 3: Network Access Control | 25% | - OT Ethernet and industrial communication models - Purdue Model and secure network segmentation - Authentication and access policies for OT devices |
| Topic 4: Monitoring and Risk Assessment | 25% | - Event handling and logging with FortiAnalyzer 7.6 - Threat detection using FortiSIEM 7.4 - OT-focused risk assessment and management |
>> Test NSEI_OTS_AR-7.6 Tutorials <<
As long as you can provide us with a transcript or other proof of your failure, we can refund you the full amount immediately. The goal of our NSEI_OTS_AR-7.6 exam questions is always to get you through the NSEI_OTS_AR-7.6 exam. If you don't pass, we won't earn you any money. This is what we should do for you as a responsible company. But our NSEI_OTS_AR-7.6 Study Materials have the high pass rate as 98% to 100%, so it is guarantee for you to pass.
NEW QUESTION # 43
Refer to the exhibit.
A partial OT network is shown.
You have recently removed the air gap in the network to provide full connectivity.
What must you configure to protect your OT network from external attacks?
Answer: A
Explanation:
The correct answer is D . Removing the air gap creates connectivity between the OT environment and external networks, significantly increasing exposure to unauthorized access and cyberattacks. Fortinet explains that the expansion of remote connectivity and IT/OT interconnections increases the OT attack surface and that the modern threat landscape requires IPS to block a wider range of threats . In the shown Purdue-style topology, FortiGate_Level5 is positioned at the upper boundary toward external connectivity and is therefore the appropriate enforcement point for protecting against attacks entering from outside the OT environment. Virtual patching at Level 2 is intended primarily to compensate for known vulnerabilities on specific OT devices that cannot yet be patched. Application Control provides industrial protocol visibility and command-level control, while merely enabling OT signatures at Level 3 does not replace perimeter intrusion prevention. Consequently, IPS belongs on FortiGate_Level5 .
NEW QUESTION # 44
Refer to the exhibit.
A partial OT network is shown. You want to configure an automated alert sent by FortiAnalyzer when an attack occurs on a FortiGate device. Which two configurations must you implement? (Choose two answers)
Answer: A,B
Explanation:
The correct answers are A and D . The study guide provides a direct use case called Attack Detection and Automated Alert . It states: "A downstream FortiGate detects an attack and sends logs to FortiAnalyzer. FortiAnalyzer parses the logs and notifies the root FortiGate. The root FortiGate triggers the action, which in this case, is a notification to the administrator." The same slide also explicitly shows "Stitches configured on root FortiGate." This confirms that to send the automated alert, you must configure the automation stitch on the root FortiGate .
The second required configuration is an event handler on FortiAnalyzer . The guide explains that "Event handlers generate events" and that "FortiAnalyzer uses event handlers to filter all incoming logs. If logs match the conditions configured in an event handler, FortiAnalyzer generates an event." Since FortiAnalyzer must detect the attack from the received logs before notifying the root FortiGate, an event handler is required on FortiAnalyzer.
Option B is incorrect because the study guide does not identify a LOCALHOST task as the required configuration for this attack-alert flow. Option C is also incorrect because the question asks what must be configured to enable the automated alert workflow . An IPS profile may detect some attacks, but the required automation path in the study guide is specifically event handler on FortiAnalyzer + stitch on the root FortiGate .
NEW QUESTION # 45
Refer to the exhibit.
A firewall policy page is shown. To improve the security of your OT network, you have configured a Supervisor profile in the firewall policies, as shown in the exhibit. However, a supervisor is reporting that he cannot ping PLC-1. What are the two reasons? (Choose two answers)
Answer: A,B
Explanation:
The correct answers are A and C .
Option A is correct because the study guide explains that with active authentication , FortiGate prompts the user only when they use "an acceptable login protocol." It states: "When you use only active authentication, if all possible policies that could match the source IP address have authentication enabled, then the user will receive a login prompt (assuming they use an acceptable login protocol)." A direct ping to PLC-1 uses ICMP , which is not the kind of login protocol used to trigger user authentication.
So the supervisor must first authenticate through a protocol such as HTTPS or Telnet , then the ICMP traffic can match the authenticated policy.
Option C is also correct because the exhibit shows policy ID 8 greyed out, meaning it is not enabled. That policy appears above the Supervisor_access (9) policy and allows broader access to PLC-1 , whereas policy 9 is limited to ALL_ICMP . The study guide explains that "Because the user has not yet authenticated, the user group aspect of the traffic does not match" and FortiGate continues searching for another complete match. In this case, with policy 8 disabled, the supervisor is left with only the ICMP rule, which cannot be used to perform the initial login step needed for active authentication.
Option B is not supported by the exhibit. Option D is incorrect because auth-on-demand always would force authentication prompts more aggressively, but the core problem here is that the user is trying to start with ICMP and the broader policy that could permit the initial authenticated access is disabled.
NEW QUESTION # 46
Refer to the exhibit.
A Run_report task is shown. You want to automate the generation of a newly created report on FortiAnalyzer . When you configure the Run_report task in Playbook, why is the report not shown in the Report field? (Choose two answers)
Answer: A,D
Explanation:
Based on the architecture of FortiAnalyzer within the Security Fabric and its automation capabilities:
* Automation Stitch and Reports : Within the Security Fabric environment, FortiAnalyzer serves as a key element in creating automation stitches and playbooks. For a report to be selectable within a Playbook task (such as the Run_report task shown in the exhibit), it must meet specific technical prerequisites in the report configuration.
* Auto-cache Requirement (Answer C) : For a report to be used for automated generation, it must be " ready " to be processed by the engine without manual intervention. Auto-cache must be enabled in the report settings to ensure the report can be generated dynamically and efficiently when triggered by the playbook.
* Extended Log Filtering (Answer B) : Playbooks often pass specific variables from the trigger (such as a specific device IP or a time range) into the report. For the report to accept these dynamic parameters and be visible as an " automation-compatible " report in the Playbook interface, Extended Log Filtering must be enabled.
* Workflow Constraints : Without these two settings enabled on the report itself, the Playbook engine cannot guarantee the report ' s successful generation or parameter injection, and thus filters it out of the available selection list in the Run_report task.
NEW QUESTION # 47
Refer to the exhibit.
Why is the OT View tab not available in the Asset Identity Center section of the FortiGate-1 device? (Choose one answer)
Answer: D
Explanation:
The correct answer is A . The study guide states that "The OT view is not available by default. You must enable it in the Feature Visibility section of the GUI or using the CLI command shown on this slide" and shows config system settings # set gui-ot enable . It also says that "After you enable the feature, the Asset Identity Center contains an Asset Identity List tab and an OT View tab." This directly explains why the OT View tab is missing: the feature that enables the Purdue-style OT display has not been enabled yet.
The OT View is the view that displays devices in a Purdue diagram , and the Asset Identity List also shows the current Purdue level for each device. Because the answer options do not explicitly say enable OT View in Feature Visibility , option A is the intended match, since it refers to enabling the Purdue-related OT display feature. Option B is incorrect because device detection affects visibility of devices, not whether the OT View tab exists. Option C is not supported by the study guide, and option D is also not given as the requirement for showing the OT View tab.
NEW QUESTION # 48
......
According to our information there is a change for NSEI_OTS_AR-7.6, I advise you to take a look at our latest Fortinet NSEI_OTS_AR-7.6 reliable exam guide review rather than pay attention on old-version materials. You can regard old-version materials as practice questions to improve your basic knowledge. If you are searching the valid NSEI_OTS_AR-7.6 Reliable Exam Guide review which includes questions and answer of the real test, our products will be your only choice.
Real NSEI_OTS_AR-7.6 Exams: https://www.validexam.com/NSEI_OTS_AR-7.6-latest-dumps.html