According to our investigation, the test syllabus of the JN0-352 exam is changing every year. Some new knowledge will be added into the annual real exam. Some old knowledge will be deleted. So you must have a clear understanding of the test syllabus of the JN0-352 study materials. Now, you can directly refer to our study materials. Our experts have carefully researched each part of the test syllabus of the JN0-352 Study Materials. Then they compile new questions and answers of the study materials according to the new knowledge parts.
| Section | Objectives |
|---|---|
| Operations and Troubleshooting | - Junos CLI monitoring tools - Troubleshooting routing and switching issues |
| Routing Policy and Filtering | - Route filtering and preference control - Policy statements |
| Network Services | - NAT concepts in Junos - Basic multicast concepts |
| Routing Protocols | - IS-IS overview - BGP fundamentals and policy control - OSPF configuration and troubleshooting |
| High Availability | - VRRP configuration and behavior - Redundancy concepts in enterprise networks |
| Layer 2 Switching Technologies | - Ethernet switching concepts - VLANs and trunking - Spanning Tree Protocol (STP/RSTP/MSTP) |
>> Latest JN0-352 Exam Dumps <<
As we entered into such a web world, cable network or wireless network has been widely spread. And it is easier to find an online environment to do your practices. This version of JN0-352 test prep can be used on any device installed with web browsers. We specially provide a timed programming test in this online JN0-352 Test Engine, and help you build up confidence in a timed exam. With limited time, you need to finish your task in JN0-352 quiz guide, considering your precious time, we also suggest this version of JN0-352 study guide that can help you find out your problems to pass the exam.
NEW QUESTION # 127
What is the default MAC age-out timer on an EX Series switch?
Answer: A
Explanation:
The default MAC age-out timer on an EX Series switch is 300 seconds. The MAC age-out timer is the maximum time that an entry can remain in the MAC table before it "ages out," or is removed.
This configuration can influence efficiency of network resource use by affecting the amount of traffic that is flooded to all interfaces. When traffic is received for MAC addresses no longer in the Ethernet routing table, the router floods the traffic to all interfaces.
NEW QUESTION # 128
Your router receives two BGP routes for the same prefix. One route is learned from an IBGP neighbor, and the other route is learned from an EBGP neighbor. By default, which route will be selected as active in this scenario?
Answer: C
Explanation:
Once the two candidate routes have equal route preference and equal local preference (both defaulting to 100 unless modified by policy), the Junos BGP algorithm proceeds to its third decision step, which compares the length of each candidate's AS path attribute and selects whichever path carries the shortest AS path, since a shorter path is interpreted as traversing fewer autonomous system hops to reach the origin. This step occurs well before the algorithm ever reaches the specific EBGP-over-IBGP preference rule, which is only evaluated later, after local preference, AS path length, origin type, and MED have all already been compared and found equal between the candidates; because an IBGP-learned copy of a route typically retains the identical AS path that was originally received from the external AS (IBGP does not prepend the local AS number the way crossing an AS boundary does), it is entirely possible, and often the deciding scenario, for AS path length to differ between competing paths well before the algorithm would ever need to fall back on the IBGP- versus-EBGP tiebreak. Selecting a route purely because it was 'learned through IBGP' is not a rule that exists anywhere in the algorithm and would in fact typically be the opposite of Junos's later EBGP-preference tiebreak. Neither next- hop IP address value nor router ID value is compared with a 'highest wins' rule at any point in the standard path selection sequence -- where router ID is used at all, Junos prefers the lowest value, not the highest, making both of those distractors doubly incorrect.
NEW QUESTION # 129 
Click the Exhibit button.
You are troubleshooting an aggregated Ethernet interface on a Juniper Networks EX Series Switch. The aggregated Ethernet interface does not appear in the output shown in the exhibit.
Which action will solve this problem?
Answer: B
Explanation:
On EX Series switches, aggregated Ethernet (ae) interfaces do not exist by default; before any ae interface can be created, referenced, or brought into service, an administrator must first reserve the desired number of aggregated Ethernet device slots by configuring set chassis aggregated-devices ethernet device-count number at the [edit chassis] hierarchy. This statement allocates the internal resources needed for that many ae interfaces to exist as valid, configurable objects; until it is committed, any interface-level configuration referencing ae0 (such as the aggregated-ether-options and family ethernet-switching stanzas shown in the exhibit) is accepted syntactically by the CLI but never actually instantiates a live ae0 device, which is exactly why show interfaces ae0.0 returns 'device ae0 not found' despite the interface appearing fully configured.
Increasing the device-count to at least 1 (or higher, to cover the number of LAG bundles planned) immediately resolves this and allows ae0 to appear as an operational interface once its member links are also associated with it. This is a foundational and frequently overlooked prerequisite step in LAG deployment on Juniper switches. There is no separate licensing requirement for aggregated Ethernet functionality on EX Series switches, a reboot is not needed since the chassis statement takes effect upon commit, and the LACP mode (active versus passive) is unrelated to whether the ae interface object itself exists in the first place.
Reference topics: Junos Enterprise Switching - Link Aggregation, Configuring the Aggregated Ethernet Device Count.
NEW QUESTION # 130
Which two statements are correct about link aggregation? (Choose two.)
Answer: A,C
NEW QUESTION # 131
You must implement filter-based forwarding. You need to direct traffic from the 192.168.1.0/24 through vr1 and traffic from 10.210.0.128/26 through vr2.
Which configuration is correct in this scenario?
Answer: A
NEW QUESTION # 132
......
Prep4cram is a trusted platform that is committed to helping Juniper JN0-352 exam candidates in exam preparation. The Juniper JN0-352 exam questions are real and updated and will repeat in the upcoming Juniper JN0-352 Exam Dumps. By practicing again and again you will become an expert to solve all the Juniper JN0-352 exam questions completely and before the exam time.
Reliable JN0-352 Mock Test: https://www.prep4cram.com/JN0-352_exam-questions.html