DOWNLOAD the newest Test4Cram NSE7_FSN_AR-7.6 PDF dumps from Cloud Storage for free: https://drive.google.com/open?id=1_UBsgdjcA3WwWtbNYjv2q9hocoE-XOct
We boost a professional expert team to undertake the research and the production of our NSE7_FSN_AR-7.6 learning file. We employ the senior lecturers and authorized authors who have published the articles about the test to compile and organize the NSE7_FSN_AR-7.6 prep guide materials. Our expert team boosts profound industry experiences and they use their precise logic to verify the test. They provide comprehensive explanation and integral details of the answers and questions to help you pass the NSE7_FSN_AR-7.6 Exam easily.
| Section | Objectives |
|---|---|
| Topic 1: SD-WAN | - Deployment and troubleshooting - SD-WAN architecture - Overlay VPN - Application steering - Performance SLA - SD-WAN routing |
| Topic 2: Enterprise Firewall | - Centralized management and analytics - Authentication and identity - Routing and advanced networking - High availability - Security Fabric integration - VPN technologies - Advanced firewall deployment - Troubleshooting |
>> Fortinet NSE7_FSN_AR-7.6 Reliable Dumps Ppt <<
Test4Cram has designed Fortinet NSE7_FSN_AR-7.6 pdf dumps format that is easy to use. Anyone can download the Fortinet NSE7_FSN_AR-7.6 pdf questions file and use it from any location or at any time. Fortinet PDF Questions files can be used on laptops, tablets, and smartphones. Moreover, you will get actual Fortinet NSE7_FSN_AR-7.6 Pdf Dumps file.
NEW QUESTION # 176
Refer to the exhibit, which shows a partial web filter profile configuration.
The URL www.dropbox.com is categorized as File Sharing and Storage.
Which action does FortiGate take if a user attempts to access www.dropbox.com?
Answer: D
NEW QUESTION # 177
Refer to the exhibits,
which show the configuration on FortiGate and partial session information for internet traffic from a user on the internal network. If the priority on route ID 2 were changed from 10 to 0, what would happen to traffic matching that user session? (Choose one answer)
Answer: D
Explanation:
The correct answer is A. This behavior is dictated by the configuration command set snat-route-change enable shown in Exhibit 1 under config system global.
Routing Change: By changing the priority of route ID 2 from 10 to 0, it becomes lower than route ID 1 (priority 5). In FortiOS, a lower priority value indicates a more preferred route. Consequently, the active route for the destination changes from port1 to port2.
SNAT Implication: The existing session (shown in Exhibit 2) is using Source NAT (SNAT) with the IP address associated with port1 (10.200.1.1). If the traffic were simply switched to port2, the source IP would be incorrect for that interface and the return traffic would likely fail or be dropped.
snat-route-change enable: This specific setting instructs the FortiGate on how to handle established SNAT sessions when a routing change occurs that alters the preferred outgoing interface. When enabled, if a route change forces an SNAT session to a new interface, FortiGate flushes (deletes) the session from the session table. This is necessary because a live TCP session cannot survive a change in its source IP address. The client must initiate a new session, which will then be created using the new correct route (port2) and the corresponding new SNAT IP.
If this setting were disabled, the session would likely remain " sticky " to the original interface (port1) until it closed, provided the route still existed. However, the explicit configuration forces the deletion.
NEW QUESTION # 178
Refer to the exhibit, which shows a session entry.
Which statement about this session is true?
Answer: D
Explanation:
The session output reveals a session with proto=1 (ICMP) and the origin and reply directions show address and NAT translations. Specifically, the hook=post dir=org act=snat shows that source NAT is performed for outgoing packets, where the source 10.1.10.10:40602 is translated to 10.200.5.1:8 (likely ICMP id 8, not a TCP/UDP port). The reply direction, hook=pre dir=reply act=dnat, indicates destination NAT for incoming packets: packets incoming for 10.200.5.1:60430 are destination-NATed to 10.1.10.10:40602. The gateway (gwy) is listed as 10.200.1.254/10.1.0.1, which for outgoing traffic means that return traffic is directed to the gateway (10.200.1.254), per the NAT policy. This is confirmed by the FortiOS Session Table Guide, which explains that the returned ICMP reply will be routed out to this NAT gateway. The session statistics and logical flow (SNAT out, matching DNAT in) reinforce that reply traffic to the initiator traverses via
10.200.1.254.
References:
FortiOS Administration Guide: Session Table, NAT, and Route Interaction Fortinet Technical Note: Diagnose sys session list, Direction and NAT Analysis
NEW QUESTION # 179
You configure the overlay tunnels for an SD-WAN hub-and-spoke topology defined with IPsec tunnels, BGP on loopback, and dynamic BGP.
Which two are recommended IPsec settings for this topology? (Choose two answers.)
Answer: A,D
Explanation:
The SD-WAN 7.6 Enterprise Administrator Study Guide identifies the recommended BGP-on-loopback IPsec settings. For branches, it specifies:
* "Static tunnel type (remote end IP address is known)."
* "net-device enable."
Enabling net-device on the spoke creates a kernel interface for the tunnel. This assists with tunnel monitoring and management and is required to support ADVPN shortcut tunnels. Dynamic BGP establishes on-demand BGP peerings between spokes after an ADVPN shortcut is created; therefore, the spoke must support those dynamic shortcut interfaces. This makes option C correct.
The spoke should also configure localid. The FortiOS 7.6 Administrator Study Guide explains: "Local ID: if the peer accepts a specific peer ID, type that same peer ID in this field." The local ID supplies the spoke's IKE identity to the dial-up hub, allowing the hub to identify and authenticate the connecting spoke correctly.
Therefore, option D is correct.
Option A reverses the recommended roles. The hub must use a dynamic tunnel type because it operates as the dial-up server and does not require every spoke's changing public gateway address in advance.
Option B is also incorrect. The guide states: "There is no need to configure any tunnel IP address, so the IKE Mode Config is not used." BGP on loopback uses the loopback address and exchange-interface-ip instead of IKE mode configuration.
References: SD-WAN 7.6 Enterprise Administrator Study Guide, SD-WAN Overlay Design and Best Practices
, pages 118-119 and 122; FortiOS 7.6 Administrator Study Guide, IPsec VPN - Phase 1 Network Settings , page 375; FortiOS 7.6 - BGP on loopback .
NEW QUESTION # 180
Refer to the exhibit.
The partial output of FortiOS kernel slabs is shown. Which statement about total slab size is true?
Answer: A
Explanation:
The correct answer is B .
The study guide explicitly states that slabs are used by the kernel : "The kernel memory slabs are collections of objects with a common purpose. The kernel uses them to store information in memory." It also gives the exact calculation method: "Total slab size = available objects x object size" and explains that in the diagnose hardware sysinfo slab output, the columns are active objects , available objects , and object size From the exhibit:
* tcp_session 3 5 1500 ...
* available objects = 5
* object size = 1500
So:
Total slab size = 5 × 1500 = 7500
That matches option B .
Why the other options are wrong:
* A : ip_session 10 10 1408 ... gives 10 × 1408 = 14080 , but slabs are associated with the kernel , not user space
* C : ip6_session 5 0 1472 ... gives 0 × 1472 = 0 , not 1472
* D : UDPv6 15 10 1408 ... gives 10 × 1408 = 14080 , but again slabs are associated with the kernel , not user space So the verified answer is B .
NEW QUESTION # 181
......
Our NSE7_FSN_AR-7.6 study tool prepared by our company has now been selected as the secret weapons of customers who wish to pass the exam and obtain relevant certification. If you are agonizing about how to pass the exam and to get the Fortinet certificate, now you can try our NSE7_FSN_AR-7.6 learning materials. Our reputation is earned by high-quality of our NSE7_FSN_AR-7.6 Learning Materials. Once you choose our NSE7_FSN_AR-7.6 training materials, you chose hope. Our NSE7_FSN_AR-7.6 learning materials are based on the customer's point of view and fully consider the needs of our customers.
Test NSE7_FSN_AR-7.6 Testking: https://www.test4cram.com/NSE7_FSN_AR-7.6_real-exam-dumps.html
DOWNLOAD the newest Test4Cram NSE7_FSN_AR-7.6 PDF dumps from Cloud Storage for free: https://drive.google.com/open?id=1_UBsgdjcA3WwWtbNYjv2q9hocoE-XOct