Der Kundendienst ist ein wichtiger Standard für eine Firma und ZertSoft bemüht sich sehr dafür. Nachdem die Kunden Cisco 300-110 Prüfungsunterlagen gekauft haben, geben wir ihnen rechtzeitiger Bescheid über die Aktualisierungsinformation der Cisco 300-110 und schicken die neueste Version per E-Mail. Dieser Aktualisierungsdienst ist innerhalb einem Jahr gratis. Wir sind getrost mit unseren Produkten. Deshalb garantieren wir, falls Sie nach dem Benutzen der Cisco 300-110 Prüfungsunterlagen die Prüfung nicht betehen, werden wir Ihnen mit voller Rückerstattung unser Bedauern zeigen.
| Section | Weight | Objectives |
|---|---|---|
| Topic 1: Wireless Site Survey | 25% | - Pre-deployment survey and validation - Design requirements collection and constraint evaluation
- RF propagation and attenuation analysis |
| Topic 2: WLAN High Availability and Security Design | 20% | - Management and monitoring design - High availability design
|
| Topic 3: Mobility Design | 25% | - Roaming optimization
- Mobility architecture models
|
| Topic 4: Wireless Infrastructure Design | 30% | - Wireless Controller architecture and deployment
|
Die Cisco 300-110 Zertifizierungsprüfung sit eine Prüfung, die IT-Technik testet. ZertSoft ist eiune Website, die Ihnen zum Bestehen der Cisco 300-110 Zertifizierungsprüfung verhilft. Viele Menschen verwenden viel Zeit und Energie auf die Cisco 300-110 Zertifizierungsprüfung oder sie geben viel Geld für die Kurse aus, um die Cisco 300-110 Zertifizierungsprüfung zu bestehen. Mit ZertSoft brauchen Sie nicht so viel Geld, Zeit und Energie. Die zielgerichteten Übungen von ZertSoft dauern nur 20 Stunden. Sie können dann die Cisco 300-110 Zertifizierungsprüfung leicht bestehen.
15. Frage
A retail customer opened two new branch locations, and the main store HQ handles data center operations.
Each branch location has three Cisco Catalyst 9130 APs. The data center has a Catalyst 9800 WLC with 18 Catalyst 9130 APs. Growing business and poor WAN uplinks cause impacted branch AP and wireless client connectivity back to HQ, and each branch location is now planned to have its own EWC controller based on C9130 AP to keep traffic local. This new design must accommodate: guests and employees sharing the same WLAN with different VLANs, guest uplink and downlink traffic restricted to 2 Mbps, and each branch acting as secondary or tertiary backup to another branch with the data center WLC always being the primary. Which design approach should the consulting engineer take?
Antwort: A
Begründung:
This multi-constraint design scenario requires precise alignment of EWC architecture, N+1 redundancy hierarchy, AAA integration, and WLAN security policies. Option B correctly addresses all requirements.
With only three APs per branch and a requirement to keep traffic local, converting a single C9130 to EWC mode is the correct and resource-efficient approach - converting two APs to EWC (Options A and C) wastes AP capacity in a small three-AP branch. The preferred controller set to the EWC AP ensures local APs join locally. The HQ WLC as primary N+1 backup satisfies the data center WLC always being primary requirement. Other branches ' EWC APs configured as secondary and tertiary controllers creates the cross- branch redundancy hierarchy. Since guests and employees share the same SSID but require different VLANs, MAC Authentication Bypass (MAB) with AAA override allows the HQ ISE/AAA server to return VLAN attributes based on device or user identity - dynamically assigning the correct VLAN at the policy level. The
2 Mbps guest rate limiting is applied through per-client QoS policies on the EWC. Option D ' s use of local web auth for guests does not enable dynamic VLAN assignment from AAA. Reference: WLSD Study Guide
- EWC Architecture, N+1 Redundancy Hierarchy, AAA Override and Dynamic VLAN Assignment.
16. Frage
An engineer is deploying new APs to serve IEEE 802.11g through 802.11ac clients and wants to use the Ekahau Site Survey tool to verify RF coverage. Management wants the engineer to verify and create coverage maps as quickly as possible. Which configuration accomplishes the goal?
Antwort: A
Begründung:
In Ekahau Site Survey, passive mode involves listening to beacon frames and probe responses from deployed APs without the survey laptop actively associating to any SSID. This is significantly faster than active mode because no association, DHCP, or throughput test overhead is introduced -- the surveyor simply walks the floor while Ekahau passively captures signal strength data from all visible APs simultaneously. Using two wireless adapters in passive mode provides a critical speed advantage: one adapter scans 2.4 GHz channels while the second adapter simultaneously scans 5 GHz channels. Without dual adapters, a single adapter must time- multiplex between bands, reducing the sample rate per band and either slowing the survey walk or producing sparser data.
17. Frage
A customer has two Cisco WLCs configured in a SSO cluster. The wireless network supports a large warehouse. The customer purchases new iPads to replace legacy scanners. Both devices connect to a single SSID named Scanning by using WPA2 Personal. The customer wants to use a standards-based method for fast roaming on the new iPads. Which approach meets the scanner requirement and still supports the legacy scanners?
Antwort: A
Begründung:
The design challenge is enabling IEEE 802.11r Fast BSS Transition for the new iPads (the standards- based fast roaming method) while maintaining backward compatibility for legacy RF scanners that may not support 802.11r. The SSID uses WPA2 Personal (PSK), not 802.1X enterprise authentication -- therefore the correct Fast Transition variant is FT PSK (pre-shared key), not FT 802.1X (Options A and B). The critical configuration parameter is setting Fast Transition to Adaptive mode rather than mandatory. Adaptive mode is a Cisco feature that allows the AP and SSID to support both 802.11r- capable clients (which will use FT PSK for fast roaming) and non-802.11r legacy clients (which will use the standard pre-FT roaming process). In Adaptive mode, legacy scanners that cannot negotiate 802.11r during association will fall back transparently to standard roaming, while the new iPads leverage FT PSK for minimal-interruption handoffs. If Fast Transition is set to mandatory, legacy clients that do not support 802.11r will fail to associate entirely. Option C uses optimized roaming globally, which is a different mechanism and does not address the iPads' specific need for a standards-based fast roaming solution.
18. Frage
A university wants to deploy a high density of APs in an area where a high number of users congregate.
Which functionality allows the university to optimize the RF settings for APs that operate in different environments or coverage zones?
Antwort: C
Begründung:
RF Profiles are a Cisco WLC configuration construct that allows administrators to define a customized set of Radio Resource Management (RRM) parameters and apply them to a subset of APs operating in a specific environment or coverage zone. Within a university high-density deployment - where a lecture hall, outdoor quad, cafeteria, and library may each require fundamentally different RF settings - RF Profiles enable differentiation without globally modifying all RRM parameters. An RF Profile can define custom values for:
minimum mandatory data rates, maximum transmit power, minimum transmit power, channel width (20/40
/80 MHz), RxSOP thresholds, client load balancing parameters, and coverage hole detection sensitivity. This allows the engineer to apply aggressive interference mitigation settings to high-density assembly areas while maintaining full-coverage settings for perimeter zones. AP Groups (Option A) assign WLANs and interface mappings to subsets of APs but do not directly control RF parameters. RF Groups (Option B) are automatically formed by RRM and represent a cluster of APs coordinating channel and power assignment. AP Profiles (Option C) define AP behavior parameters such as NTP and SSH settings, not RF optimization parameters. Reference: WLSD Study Guide - RF Profile Configuration, High-Density WLAN Design, RRM Parameter Customization.
19. Frage
An engineer must perform a predictive wireless survey to indicate the number of access points required. The engineer has created a new project and imported the floor plan. Which step must be taken next for accurate AP placement?
Antwort: D
Begründung:
After creating a new predictive survey project and importing the floor plan, the next mandatory step is to set the scale of the floor plan. Setting the scale is critical because all subsequent measurements -- AP coverage radius, cell overlap calculations, and distance-based attenuation modeling -- depend on the accuracy of the floor plan's physical dimensions. If the scale is incorrect, the predictive model will place APs at incorrect distances relative to each other and produce inaccurate coverage predictions. The scale is typically set by the engineer clicking on two known points on the floor plan and entering the real-world distance between them, calibrating the software's measurement system.
20. Frage
......
Wenn Sie einen Traum haben, dann sollen Sie Ihren Traum verteidigen. Gorki hat einmal gesagt, dass der Glaube ist ein großes Gefühl und eine kreative Kraft ist. MeinTraum ist es, ein Top-IT-Experte zu werden. Ich denke, dass es für mich nirgends in Sicht ist. Aber Erfolg können Sie per eine Abkürzung gelingen, solange Sie die richtige Wahl treffen. Ich benutzte die ZertSoft Cisco 300-110 Prüfung Fragenkataloge, und habe die Cisco 300-110 Zertifizierungsprüfung bestanden. Die Fragenkataloge zur Cisco 300-110 Prüfung von ZertSoft sind die besten Lernhilfe. Wenn Sie wie ich einen IT-Traum haben. Dann kaufen Sie Prüfungsfragen und Antworten von ZertSoft. ZertSoftes wird Ihnen helfen, Ihren Traum zu verwirklichen.
300-110 Lernressourcen: https://www.zertsoft.com/300-110-pruefungsfragen.html