Itcertkr는 고객님께서International Code Council M2첫번째 시험에서 패스할수 있도록 최선을 다하고 있습니다. 만일 어떤 이유로 인해 고객님이International Code Council M2시험에서 실패를 한다면 Itcertkr는International Code Council M2덤프비용 전액을 환불 해드립니다. 시중에서 가장 최신버전인International Code Council M2덤프로 시험패스 예약하세요.
| Section | Objectives |
|---|---|
| Topic 1: General Administration and Mechanical Inspection Practice | - Code enforcement procedures and inspector responsibilities
|
| Topic 2: Ventilation and Indoor Air Quality | - Ventilation requirements
|
| Topic 3: HVAC Systems and Equipment | - Heating and cooling systems
|
| Topic 4: Fuel Gas Systems | - Gas piping and appliance installation
|
| Topic 5: Mechanical Code (IMC) Fundamentals | - International Mechanical Code application
|
| Topic 6: Mechanical Appliances and Equipment | - Boilers, furnaces, and water heaters
|
퍼펙트한International Code Council M2시험대비덤프자료는 Itcertkr가 전문입니다. International Code Council M2덤프를 다운받아 가장 쉬운 시험준비를 하여 한방에 패스가는것입니다. 다같이 International Code Council M2덤프로 시험패스에 주문걸어 보아요. 마술처럼International Code Council M2시험합격이 실현될것입니다.
질문 # 36
Unless listed for a greater or smaller dimension, mechanical draft venting systems shall terminate a minimum of _____ feet below an openable window.
정답：A
설명：
For mechanical draft venting systems, unless the appliance is listed for a different clearance, the vent terminal must be located not less than 4 feet below , 4 feet horizontally from , or 1 foot above any door, operable window, or gravity air inlet into a building. Therefore, the required minimum distance below an openable window is 4 feet , so Option B is correct.
질문 # 37
What is the minimum distance required between a combustion air opening at the exterior of a building and a lot line?
정답：B
설명：
The ICC opening-location rule requires intake openings to be located not less than 10 feet from lot lines or buildings on the same lot . A combustion-air opening taken from the exterior follows that minimum separation rule, so 10 feet is the correct answer. Therefore, Option D is correct.
질문 # 38
When a permit is issued, the code requires that one set of approved plans and specifications be returned to the applicant.
This set of plans and specifications shall be:
정답：A
설명：
Under the ICC administrative provisions used with the mechanical code, one approved set is retained by the code official, and one approved set is returned to the applicant. The returned set must be kept on the site of the building or job while the authorized work is in progress. That directly matches Option A . It does not require return to the architect, filing with the county clerk, or retention for one year after completion.
질문 # 39
Given: single-wall vent, which serves only one appliance, and has a height of 10 feet.
The maximum horizontal length permitted for a 5-inch diameter vent connector serving this vent is _____ feet.
정답：A
설명：
For a single-wall vent connector serving one appliance, the maximum horizontal length is determined from the vent connector sizing and length rules. For a 5-inch diameter connector with a 10-foot vent height , the permitted maximum horizontal length is 7.5 feet . Therefore, Option B is correct.
질문 # 40
To test for tightness, a consumer's gas piping should never be filled with:
정답：B
설명：
The IFGC section on test medium states that the test medium shall be air, nitrogen, carbon dioxide or an inert gas , and specifically states that oxygen shall not be used as a test medium . That makes C the correct answer.
질문 # 41
......
International Code Council M2 시험을 한번에 합격할수 없을가봐 두려워 하고 계시나요? 이 글을 보고 계신 분이라면 링크를 클릭하여 저희 사이트를 방문해주세요. 저희 사이트에는International Code Council M2 시험의 가장 최신 기출문제와 예상문제를 포함하고 있는 International Code Council M2덤프자료를 제공해드립니다.덤프에 있는 문제와 답을 완벽하게 기억하시면 가장 빠른 시일내에 가장 적은 투자로 자격증 취득이 가능합니다.
M2인증자료: https://www.itcertkr.com/M2_exam.html