The Fortinet NSE 7 - Secure Networking 7.6 Architect (NSE7_FSN_AR-7.6) certification test is an important part of career growth, and passing it may lead to more employment opportunities. However, preparing for the Fortinet NSE 7 - Secure Networking 7.6 Architect (NSE7_FSN_AR-7.6) test may be tough, and many busy applicants have difficulty cracking it. This is where FreeCram Fortinet NSE 7 - Secure Networking 7.6 Architect real exam questions come to help you clear the test in a short time.
| Section | Objectives |
|---|---|
| Enterprise Firewall | - Troubleshooting
|
| SD-WAN | - Traffic steering
|
>> Latest NSE7_FSN_AR-7.6 Learning Material <<
The Fortinet NSE 7 - Secure Networking 7.6 Architect (NSE7_FSN_AR-7.6) certification exam is one of the best credentials in the modern Fortinet world. The Fortinet NSE 7 - Secure Networking 7.6 Architect (NSE7_FSN_AR-7.6) certification offers a unique opportunity for beginners or experienced professionals to demonstrate their expertise and knowledge with an industry-recognized certificate. With the Fortinet NSE7_FSN_AR-7.6 Exam Dumps, you can not only validate your skill set but also get solid proof of your proven expertise and knowledge.
NEW QUESTION # 139
Refer to the exhibits, which contain the partial configurations of two VPNs on FortiGate.
An administrator has configured two VPNs for two different user groups. Users who are in the Users-2 group are not able to connect to the VPN. After running a diagnostics command, the administrator discovers that FortiGate is not matching the user-2 VPN for members of the Users-2 group.
Which two changes must the administrator make to fix the issue? (Choose two.)
Answer: A,D
Explanation:
The key point is that the two VPNs are dynamic dialup IPsec tunnels on the same interface and both are using IKEv1 main mode. In this design, FortiGate cannot reliably distinguish which dialup phase1 to match before phase 1 completes.
The uploaded Network Security Support Engineer 7.6 Study Guide shows that XAuth happens only after phase 1 is already established:
"The IKE real-time debug shows, after phase 1, the exchange of extended authentication (XAuth) packets...
You can also see the CFG_REPLY, showing the XAuth user and group name." That means the user group is learned too late to be used for selecting the correct phase1 definition. So the fix must be applied to the phase1 matching method itself, not to XAuth.
The FortiOS administration guide gives the exact rule for this scenario:
"When the remote VPN peer has a dynamic IP address and is authenticated by a pre-shared key you must select Aggressive mode if there is more than one dialup phase 1 configuration for the interface IP address."
NEW QUESTION # 140
Refer to the exhibit, which shows a partial output of the fssod daemon real-time debug command.
What two conclusions can you draw from the output? (Choose two.)
Answer: B,C
Explanation:
https://community.fortinet.com/t5/FortiGate/Troubleshooting-Tip-How-to-troubleshoot-FSSO-agentless-polling/ta-p/214349 From the snippet we can see that FortiGate (via the fssod daemon) is directly detecting the user logon rather than relying on a separate "collector" or "DC agent." This indicates agentless polling-FortiGate polls the DC's event logs over TCP 445 to discover logons. So: - FSSO is using agentless polling mode to detect logon events - In agentless mode, FortiGate will periodically poll the same IP (the DC) on port 445 to see if the user is still logged on
NEW QUESTION # 141
Refer to the exhibit, which shows a partial output of the real-time LDAP debug.
What two actions can the administrator take to resolve this issue? (Choose two.)
Answer: A,D
NEW QUESTION # 142
Refer to the exhibit.
Which two statements about the output are true, considering NGFW-1 and NGFW-2 have been up for a week? (Choose two.)
Answer: A,D
Explanation:
The correct answers are A and B.
The exhibit shows:
override: disable
both members are currently in-sync
only port7 appears under HBDEV stats, so it is the active heartbeat interface the cluster is in HA A-P mode Why A is correct:
With override disabled, after a failover the new primary keeps that role when the old primary comes back.
The FortiOS administration guide states:
"When the primary FortiGate rejoins the cluster the secondary FortiGate continues to operate as the primary FortiGate." So if FGVM...649 reboots and FGVM...650 becomes primary, FGVM...650 will remain primary after FGVM...649 rejoins.
Why B is correct:
The study guide states:
"When FortiGate devices configured in an HA cluster lose communication with each other on the heartbeat interface, each FortiGate assumes the role of the primary device." The exhibit shows only port7 as the heartbeat device in HBDEV stats So if port7 is disconnected and heartbeat communication is lost, the cluster can enter a split-brain condition, where both units believe they are primary. The FortiOS administration guide confirms the same behavior: loss of heartbeat communication causes each member to think it is the primary Why the other options are wrong:
C is wrong because configuration synchronization status is specifically used to detect whether secondary members remain synchronized with the primary. If members are no longer synchronized, the status changes from in-sync to out-of-sync D is wrong because the study guide explains that during a configuration change, checksums may differ briefly while changes are copied, but it does not describe this as the secondary initiating a "synchronization reset" So the verified answers are: A, B.
NEW QUESTION # 143
Refer to the exhibit.
Two hub-and-spoke groups are connected through redundant site-to-site IPsec VPNs between Hub 1 and Hub
2.
Which two configuration settings are required for Spoke A1 to establish an auto-discovery VPN (ADVPN) shortcut with Spoke B2? (Choose two.)
Answer: C,D
Explanation:
Comprehensive and Detailed 100 to 150 words of Explanation From Secure Networking Architect Study Guides topics:
For inter-region ADVPN shortcuts, each IPsec interface must be configured according to its ADVPN role.
The Enterprise Firewall 7.6 Administrator Study Guide states that when a spoke connects to a hub, auto- discovery-receiver must be enabled so that the spoke can receive shortcut messages and initiate negotiation of a dynamically created shortcut tunnel. Therefore, A is correct.
When hubs are interconnected through IPsec, the hub-to-hub tunnel must use auto-discovery-forwarder enable. This permits shortcut messages to cross the overlay networks and reach spokes in another region, making B correct. auto-discovery-sender belongs on the hub-facing ADVPN interface used to send shortcut offers to spokes, not on the spoke. Likewise, the hub is not configured as the receiver on its spoke-facing tunnels.
NEW QUESTION # 144
......
Our NSE7_FSN_AR-7.6 guide torrent has gone through strict analysis and summary according to the past exam papers and the popular trend in the industry and are revised and updated. The NSE7_FSN_AR-7.6 exam questions have simplified the sophisticated notions. The software boosts varied self-learning and self-assessment functions to check the learning results. The software of our NSE7_FSN_AR-7.6 Test Torrent provides the statistics report function and help the students find the weak links and deal with them. With this version of our NSE7_FSN_AR-7.6 exam questions, you will be able to pass the exam easily.
NSE7_FSN_AR-7.6 Reliable Test Dumps: https://www.freecram.com/Fortinet-certification/NSE7_FSN_AR-7.6-exam-dumps.html