그렇게 많은 IT인증덤프공부자료를 제공하는 사이트중Fast2test의 인지도가 제일 높은 원인은 무엇일가요?그건Fast2test의 제품이 가장 좋다는 것을 의미합니다. Fast2test에서 제공해드리는 Huawei인증 H35-831덤프공부자료는Huawei인증 H35-831실제시험문제에 초점을 맞추어 시험커버율이 거의 100%입니다. 이 덤프만 공부하시면Huawei인증 H35-831시험패스에 자신을 느끼게 됩니다.
Huawei H35-831 시험은 데이터 커뮤니케이션 및 캐리어 네트워크에 대한 기술과 지식을 향상시키려는 숙련 된 네트워크 전문가를위한 것입니다. 이 시험은 복잡한 데이터 통신 및 캐리어 네트워크 설계, 구현 및 관리를 담당하는 네트워크 엔지니어, 네트워크 관리자 및 네트워크 아키텍트에게 이상적입니다. 이 시험은 후보자의 데이터 통신 및 운송 업체 네트워크를 설계, 배포 및 문제 해결하는 능력을 검증하고 구직 시장에서 경쟁 우위를 제공합니다.
Huawei H35-831 인증 시험은 캐리어 네트워크에서 데이터 통신과 관련된 다양한 주제를 다룹니다. 이는 네트워크 아키텍처, 네트워크 프로토콜, 네트워크 보안, 네트워크 관리 및 네트워크 최적화를 포함합니다. 이 시험은 객관식 문제와 시뮬레이션으로 구성되어 있으며, 시험에서 다루는 주제에 대한 이해력을 시험합니다. 시험에 합격하려면 최소 1000점 중 600점 이상을 받아야합니다. Huawei H35-831 인증을 통해 개인들은 캐리어 네트워크에서 데이터 통신에 대한 전문 지식을 입증하며 IT 산업에서 경력 기회를 향상시킬 수 있습니다.
Fast2test 에서는 IT인증시험에 대비한 퍼펙트한Huawei 인증H35-831덤프를 제공해드립니다. 시험공부할 시간이 충족하지 않은 분들은Fast2test 에서 제공해드리는Huawei 인증H35-831덤프로 시험준비를 하시면 자격증 취득이 쉬워집니다. 덤프를 구매하시면 일년무료 업데이트서비스도 받을수 있습니다.
Huawei H35-831 (HCIE-Datacom-Carrier (작성) v1.0) 인증 시험은 복잡한 운송 업체 별 데이터 커뮤니케이션 네트워크 설계, 계획, 구성 및 문제 해결에서 전문가의 기술 전문 지식을 검증하는 세계적으로 인정 된 인증 시험입니다. 인증은 데이터 커뮤니케이션 및 네트워킹 분야에서 최소 5 년의 경험을 가진 전문가에게 적합하며 경력 발전 및 더 높은 급여를위한 기회를 제공합니다.
질문 # 19
In the inter-AS VPN Option A network shown, CE1 and CE2 are in the same VPN. LDP and IGP are configured in both AS100 and AS200, and EBGP is configured between the ASBRs. CE1's loopback interface is assigned 10.1.1.1/32. If CE2 can ping CE1, which router assigns the inner label to CE2-to-CE1 packets forwarded by PE2?
Exhibit 45.1 - Original topology/configuration figure
정답:B
설명:
Huawei Reference Verification:
In Huawei inter-AS MPLS VPN Option A, each ASBR runs customer VPN instances and exchanges VPN route information with its opposite ASBR over an ordinary inter-AS IP routing relationship. The ASBR-to- ASBR boundary resembles a CE-PE attachment rather than a single end-to-end MPLS VPN LSP. Within each AS, local MP-BGP advertisements include locally allocated VPN labels. For traffic traveling from CE2 in AS200 toward CE1 in AS100, ASBR2 advertises the CE1 destination route to PE2 using the VPN label allocated by ASBR2. Therefore ASBR2 supplies PE2's inner VPN label.
Technical Deep Dive:
B is correct. CE1 originates route 10.1.1.1/32, which PE1 learns and advertises through VPNv4 toward ASBR1 in AS100. In Option A, ASBR1 exchanges the corresponding ordinary IP route across the inter-AS VPN attachment to ASBR2. ASBR2 then advertises it to PE2 in AS200 as a labeled VPNv4 route and allocates its local VPN label. PE2 pushes this VPN label as the inner label and, where necessary, a public transport label outside it. P2 handles the transport forwarding, while ASBR2 interprets the local VPN context and forwards the packet across the AS boundary. The labels used in AS100 and AS200 need not be the same.
The defining principle of Option A is that VPN state and inter-AS connectivity terminate on both ASBRs, avoiding one continuous end-to-end VPN label stack.
#######################################################
질문 # 20
A device receives two BGP routes for the same prefix from two peers, with one route received from each peer. One route has next hop NH1, whereas the other has next hop NH2. All other attributes of the two routes are identical. NH1 recursively resolves to two direct next hops, A and B, and NH2 likewise recursively resolves to two direct next hops, C and D. If BGP is configured with the maximum load-balancing 2 command and the device supports at most six load-balancing routes, how many load-balancing routes for the relevant prefix are present in the FIB?
정답:A
설명:
Huawei Reference Verification:
Huawei's BGP multipath architecture distinguishes the number of BGP routes selected from the number of directly reachable FIB next hops produced by route recursion. The maximum load-balancing parameter controls the number of eligible equal-cost BGP paths. Each selected BGP next-hop address may recursively resolve through multiple equal-cost direct next hops. In this scenario two BGP paths are selected and each resolves through two direct forwarding alternatives. The total of four FIB next hops remains within the stated platform maximum of six. Therefore the correct answer is four.
Technical Deep Dive:
A is correct. `maximum load-balancing 2` permits two equivalent BGP paths for one destination, which here have BGP next hops NH1 and NH2. Route recursion then considers the IGP or directly connected paths that make each BGP next hop reachable. NH1 resolves to direct next hops A and B, while NH2 resolves to C and D: The installed FIB next-hop group therefore contains A, B, C and D, four choices in total. The device's six- path upper limit is a cap rather than a requirement to synthesize six routes. On Huawei carrier routers, the BGP control plane selects and resolves paths; forwarding NP/ASIC logic performs ECMP selection among the installed direct next hops. Useful diagnostic commands include `display bgp routing-table`, `display ip routing-table`, and `display fib`. The distinction between BGP multipath selection and physical recursive next- hop expansion is the key to the question.
#######################################################
질문 # 21
Which of the following statements is incorrect about the SR-TE tunnel configuration below?
[R1] interface tunnel1
[R1-Tunnel1] ip address unnumbered interface LoopBack0
[R1-Tunnel1] tunnel-protocol mpls te
[R1-Tunnel1] destination 3.3.3.3
[R1-Tunnel1] mpls te tunnel-id 1
[R1-Tunnel1] mpls te signal-protocol segment-routing
[R1-Tunnel1] mpls te pce delegate
Select all that apply.
정답:A,D
설명:
Huawei Reference Verification:
Huawei's SR-TE tunnel CLI separates the transport tunnel type, the signaling protocol and the path- management mode. `tunnel-protocol mpls te` establishes an MPLS TE tunnel interface; `mpls te signal- protocol segment-routing` identifies Segment Routing as its signaling technology. `ip address unnumbered interface LoopBack0` borrows the Loopback0 address, and `mpls te tunnel-id 1` sets the tunnel identifier. The command `mpls te pce delegate` delegates LSP path management to the PCE through PCEP, rather than specifying a manually configured explicit path. Therefore the claims that SR is the tunnel protocol or that the path is manually specified are incorrect.
Technical Deep Dive:
C and D are incorrect. The displayed interface is a Tunnel1 MPLS TE tunnel whose address is borrowed from LoopBack0 and whose destination is 3.3.3.3. The tunnel ID is 1, unique as required within the applicable tunnel context. Segment Routing in this configuration is the signaling mechanism, not the value of the `tunnel- protocol` field. PCE delegation transfers supported LSP path computation/management to a Path Computation Element; it does not define a static explicit-path sequence locally. A manual explicit path would require its own explicit-path configuration and reference. PCEP is a TCP-based control protocol allowing the PCC to report LSP state and the PCE to deliver calculated routes or updates. An operational engineer can inspect the status with `display interface tunnel 1`, `display mpls te tunnel` and `display current-configuration interface Tunnel1`. The broader lesson is to read CLI keywords according to the configuration hierarchy rather than interpreting the presence of 'segment-routing' as a replacement of the underlying MPLS TE tunnel type.
#######################################################
질문 # 22
Under which of the following conditions must OSPF TE and IS-IS TE flood link information?
Select all that apply.
정답:A,B,C,D
설명:
Huawei Reference Verification:
Huawei's OSPF TE and IS-IS TE implementations flood link-state and traffic-engineering information so that routers and traffic-engineering controllers can maintain an accurate TEDB. Triggers include topology changes when links become active or fail, changes in TE attributes, and periodic refresh when the flooding interval expires. In addition, insufficient bandwidth resources discovered during LSP setup can prompt updated TE resource advertisements so that other path-computing nodes have current information. These update conditions keep link attributes, bandwidth availability, and topology consistent throughout the routing domain. Thus all four conditions are relevant.
Technical Deep Dive:
A, B, C and D are correct. Traffic Engineering uses information beyond basic reachability: maximum reservable bandwidth, unreserved bandwidth, TE metrics and administrative groups/affinities may determine whether a constrained LSP can be established. Link activation or failure requires an immediate topology update. Administrative-group or bandwidth changes may affect which links remain eligible. TE refresh intervals ensure that relevant advertisements remain current, while a failed bandwidth reservation can trigger an availability update so other computations avoid the exhausted resource. OSPF TE distributes information in opaque LSAs, and IS-IS TE uses appropriate TLVs. CSPF relies on these advertisements to build the traffic- engineering database and determine paths meeting service requirements. Missing or delayed updates can cause setup failures or inappropriate path selection. The precise event thresholds and suppression timers are release- and configuration-dependent, but each listed condition can prompt TE link-state advertisement.
#######################################################
질문 # 23
In an SDN network, device control planes are deployed centrally. If a node or link in the SDN network fails, which of the following is the optimal protection method?
정답:A
설명:
Exact Extract - Huawei Training Material (Automatic SDN Network O & M, p.22):
"Automatic service recovery: Based on service SLA requirements, NCE recalculates a service path based on SRv6, isolates the faulty node, and automatically restores the faulty service." Huawei Reference Verification:
Huawei's Automatic SDN O & M curriculum describes centralized path computation and controller-driven restoration after faults. For millisecond-level protection, the better design is to compute and install backup FRR forwarding state in advance. A failed link or node can then trigger immediate local switching to the alternate entry on the forwarder, avoiding the delay of reporting the fault, waiting for a controller decision and receiving new entries. Controller recalculation remains useful for later optimization and restoration. Therefore an SDN controller delivering FRR routes ahead of failure is the optimal choice.
Technical Deep Dive:
D is correct. The controller has a global topology view and can calculate primary and backup transport paths based on bandwidth, policy and service SLA. Rather than waiting for a fault before computing everything, it distributes the required FRR backup entries proactively. Upon link-down or BFD notification, the router's forwarding subsystem switches to the preinstalled alternate next hop or tunnel, minimizing customer interruption. Recomputing routes after failure through the controller introduces detection, signaling, calculation and programming delay. Forwarders can compute local routing in distributed architectures, but the question specifies centralized control and asks for the optimal immediate protection. IP FRR, TI-LFA, SR-TE backup paths and VPN FRR are examples of underlying forwarding protections. Supported Huawei NP/ASIC hardware performs fast local switching once the backup forwarding state is installed. Controller-based path optimization can then restore the desired long-term service state.
#######################################################
질문 # 24
......
H35-831퍼펙트 덤프공부: https://kr.fast2test.com/H35-831-premium-file.html