Our company have the higher class operation system than other companies, so we can assure you that you can start to prepare for the NSEI_OTS_AR-7.6 exam with our study materials in the shortest time. In addition, if you decide to buy NSEI_OTS_AR-7.6 exam materials from our company, we can make sure that your benefits will far exceed the costs of you. The rate of return will be very obvious for you. We sincerely reassure all people on the NSEI_OTS_AR-7.6 Test Question from our company and enjoy the benefits that our study materials bring. We believe that our study materials will have the ability to help all people pass their NSEI_OTS_AR-7.6 exam and get the related exam in the near future.
| Section | Objectives |
|---|---|
| Topic 1: Monitoring and Risk Assessment | - Analyze security reports from FortiAnalyzer - Perform risk assessment and management - Create FortiAnalyzer event handlers |
| Topic 2: Asset Management | - Implement device detection on FortiGate and FortiNAC - Explain OT standards and Fortinet compliance - Use Fortinet Security Fabric for an OT network |
| Topic 3: Network Security | - Configure security inspections for industrial protocols - Configure automation - Configure virtual patching |
| Topic 4: Network Access Control | - Configure network access authentication - Configure network segmentation schemas - Explain OT Ethernet concepts |
>> NSEI_OTS_AR-7.6 Reliable Braindumps Ppt <<
The NSEI_OTS_AR-7.6 Learning Materials of us are pass guaranteed and money back guaranteed. Since the NSEI_OTS_AR-7.6 exam dumps are of high accuracy and high quality, and it can ensure you pass the exam successfully. We also give you any help you want, if you need any help or you have any questions, just contact us without any hesitation, we will do all we can to help you pass the exam. Just have a try, and you will benefit a lot.
NEW QUESTION # 38
Refer to the exhibit.
A partial OT network is shown. You must improve the security of this OT network and implement internal segmentation between network 1 and network 2. How can you achieve the segmentation? (Choose one answer)
Answer: D
Explanation:
The correct answer is D. You can configure forward domain IDs for each network .
The study guide explains that in FortiGate transparent mode, all interfaces belong to the same broadcast domain, even interfaces with different VLAN IDs , and then states that you can "subdivide into multiple broadcast domains" by configuring set forward-domain < domain_ID > . It also states that "interfaces with the same domain ID belong to the same broadcast domain" and, with multiple forward domains,
"traffic arriving on one interface is broadcast only to interfaces in the same forward domain ID." That is the mechanism used to separate internal networks and confine traffic between network segments.
The other options do not fit this requirement. Universal ZTNA is for application access control, not segmentation between two OT networks. One traffic VDOM does not create segmentation by itself; multiple VDOMs would be needed for that type of isolation. An explicit software switch controls intraswitch traffic inside the same software-switch domain, not segmentation between separate networks like network 1 and network 2. Therefore, the correct way to implement the internal segmentation asked in the question is to assign different forward domain IDs to each network.
NEW QUESTION # 39
Refer to the exhibit.
A partial OT network is shown. You have configured the FortiGate device with VLANs to segment the OT network. The supervisor now wants to connect to the PLC from the Engineering Workstation. How can you allow access from the Engineering Workstation to the PLC? (Choose one answer)
Answer: A
Explanation:
The correct answer is D. You must configure a layer 3 switch .
The study guide explains that "Layer 2 devices can add or remove tags" but "cannot modify them." It then states that "A layer 3 device, such as a router or FortiGate, can modify the VLAN tag before routing the packet. This allows them to route traffic between VLANs." It also explicitly describes
"Router on a Stick" as "a way to allow routing between VLANs." Since the exhibit shows a layer-2 switch and the Engineering Workstation and PLC are placed in different VLANs, inter-VLAN communication requires layer-3 routing.
The other options do not solve this requirement. intra-switch-policy explicit/implicit applies to a software switch , where member interfaces are in the same broadcast domain and same subnet, not to routing between separate VLANs. forward domain IDs are used in transparent mode to confine broadcasts to specific broadcast domains; they do not provide inter-VLAN access. Therefore, to let the Engineering Workstation in one VLAN reach the PLC in another VLAN, you need a layer 3 routing function , which matches option D .
NEW QUESTION # 40
Refer to the exhibit.
A partial OT network is shown. In this OT network, you must add additional security measures to detect OT protocols and, therefore, increase the traffic visibility. Which security sensor must you implement to detect the OT protocols in this network? (Choose one answer)
Answer: B
Explanation:
The correct answer is C. Application sensor set to monitor on all the FortiGate devices .
The study guide clearly explains that application control is the feature used to identify OT protocols. It states that "application control detects the protocols used in applications like Modbus, IEC 104, and the contents of the telecontrol messages" and also says "You can use application control signatures to detect OT protocols." It further shows an example where a Modbus application control profile is enabled on a firewall policy "for OT protocol visibility in the monitor status." This directly matches the requirement in the question, which is to detect OT protocols and increase traffic visibility .
The other options do not fit the requirement as precisely. Device detection is for identifying devices and collecting endpoint information, not for detecting industrial protocols. Inline IDS and IPS are focused more on detecting or blocking attacks, exploits, protocol abnormalities, and known vulnerabilities. While IPS can inspect some OT traffic, the study guide distinguishes it from application control by stating that IPS signatures tend to detect exploits, whereas application control signatures tend to provide protocol detection at various levels . Therefore, the required security sensor for OT protocol detection and traffic visibility is the application sensor in monitor mode .
NEW QUESTION # 41
Refer to the exhibit.
The OT devices behind the ruggedized FortiGate have vulnerabilities and you want to apply a virtual patching profile in the firewall policy. Why is Virtual Patching not available in the Security Profiles section? (Choose one answer)
Answer: B
Explanation:
The correct answer is A. You must enable Virtual Patching in the Feature Visibility section .
The study guide states clearly that "By default, virtual patching profiles are hidden on the GUI, and you must enable them through System > Feature Visibility." That exactly matches the situation in the exhibit, where Virtual Patching does not appear under Security Profiles . So the issue is not that the feature is unsupported, but that it is simply hidden in the GUI until it is enabled.
The other options do not answer the question being asked. A valid OT security service license is required for virtual patching signatures and protection workflow, and OT signatures are relevant to IPS-based OT protection, but those do not explain why the menu item itself is missing from the Security Profiles section .
The guide specifically identifies Feature Visibility as the reason the Virtual Patching profile is not shown in the GUI. Therefore, the required action is to enable Virtual Patching in System > Feature Visibility .
NEW QUESTION # 42
Refer to the exhibit. A partial OT network is shown. You must improve the security of this OT network and implement internal segmentation between network 1 and network 2. How can you achieve the segmentation?
(Choose one answer)
Answer: D
Explanation:
The correct answer is D. You can configure forward domain IDs for each network . The study guide explains that in FortiGate transparent mode, "all interfaces belong to the same broadcast domain, even interfaces with different VLAN IDs" and then states that you should "use this command to subdivide into multiple broadcast domains" with set forward-domain < domain_ID > . It further explains that
"interfaces with the same domain ID belong to the same broadcast domain" and "traffic arriving on one interface is broadcast only to interfaces in the same forward domain ID." This is exactly the mechanism used to separate one internal network from another and improve segmentation.
The other options do not match this requirement. Universal ZTNA is described as controlling user access to applications , not segmenting two internal OT networks. An explicit software switch is for controlling intra- switch or intra-VLAN traffic inside the same software switch broadcast domain, which is more aligned with microsegmentation than separating two routed internal networks. One traffic VDOM does not create segmentation by itself; segmentation with VDOMs requires multiple VDOMs, not one. Therefore, the best choice for segmenting network 1 and network 2 in this scenario is to assign separate forward domain IDs .
NEW QUESTION # 43
......
The internet is transforming society, and distance is no longer an obstacle. You can download our NSEI_OTS_AR-7.6 exam simulation from our official website, which is a professional platform providing the most professional NSEI_OTS_AR-7.6 practice materials. You can get them within 15 minutes without waiting. What is more, you may think these high quality NSEI_OTS_AR-7.6 Preparation materials require a huge investment on them. Actually we eliminate the barriers blocking you from our NSEI_OTS_AR-7.6 practice materials. The price of our NSEI_OTS_AR-7.6 exam question is quite favourable for you to buy.
NSEI_OTS_AR-7.6 Fresh Dumps: https://www.itpass4sure.com/NSEI_OTS_AR-7.6-practice-exam.html