All these three FlashArray-Storage-Professional exam question formats contain the real, updated, and error-free FlashArray-Storage-Professional exam practice test. These Pure Storage FlashArray-Storage-Professional exam questions give you an idea about the final Pure Storage FlashArray-Storage-Professional exam questions formats, exam question structures, and best possible answers, and you will also enhance your exam time management skills. Finally, at the end of Pure Storage FlashArray-Storage-Professional Exam Practice test you will be ready to pass the final Pure Storage FlashArray-Storage-Professional exam easily. Best of luck in Pure Storage FlashArray-Storage-Professional exam and professional career!!!
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
>> Exam FlashArray-Storage-Professional Bible <<
Our company is considerably cautious in the selection of talent and always hires employees with store of specialized knowledge and skills on our FlashArray-Storage-Professional exam questions. All the members of our experts and working staff maintain a high sense of responsibility, which is why there are so many people choose our FlashArray-Storage-Professional Exam Materials and to be our long-term partner. Believe in our FlashArray-Storage-Professional study guide, and you will have a brighter future!
NEW QUESTION # 61
Which command provides the negotiated port speed of an ethernet port?
Answer: A
Explanation:
On a Pure Storage FlashArray, Ethernet ports operate at both a physical hardware layer and a logical network configuration layer. If you need to verify the actual physical negotiated port speed of an Ethernet port (for example, verifying if a 25GbE port negotiated down to 10GbE due to switch configurations or cable limitations), you must query the hardware layer directly.
The command purehw list --all --type eth interacts directly with the physical NIC hardware components to report their true link status, health, and dynamically negotiated hardware link speed.
Here is why the other options are incorrect:
purenetwork eth list -- all (B): The purenetwork command suite is primarily focused on the logical Layer 2/Layer 3 networking stack. It is used to configure and list IP addresses, subnet masks, MTU sizes (Jumbo Frames), and routing, rather than focusing on the physical hardware negotiation details of the NIC itself.
pureport list (A): The pureport command suite is specifically used for managing and viewing storage protocol target ports. An administrator would use this to list the array's Fibre Channel WWNs or iSCSI IQNs to configure host zoning or initiator connections, not to verify Ethernet link negotiation speeds.
NEW QUESTION # 62
What command must an administrator run to use newly installed DirectFlash Modules (DFM)?
Answer: C
Explanation:
When new DirectFlash Modules (DFMs) or data packs are physically inserted into a Pure Storage FlashArray, the Purity operating environment detects the new hardware but places the drives in an "unadmitted" state. This safety mechanism prevents the accidental incorporation of drives and allows the system to verify the firmware and health of the modules before they are actively used to store data.
To formally accept these drives into the system's storage pool so their capacity can be utilized, the administrator must execute the CLI command puredrive admit. Once this command is run, the drive status transitions from "unadmitted" to "healthy," and the array's usable capacity expands accordingly.
Here is why the other options are incorrect:
pureadmin -- admit-drive (A): This is syntactically incorrect. The pureadmin command suite is used for managing administrator accounts, API tokens, and directory services, not for hardware or drive management.
purearray admit drive (B): This is also incorrect syntax. While purearray is used for array-wide settings and status (like renaming the array or checking space), specific drive-level operations are exclusively handled by the puredrive command structure.
NEW QUESTION # 63
An administrator is running commands to verify NVME/TCP connectivity from the hosts to the FlashArray. They use the command ping -M do -s 8972 <ip_addr> from the initiator and it fails.
What should the administrator do to resolve the issue?
Answer: A
Explanation:
When configuring NVMe/TCP (or iSCSI) for optimal performance on a Pure Storage FlashArray, configuring Jumbo Frames (an MTU of 9000) end-to-end is a standard best practice.
The command ping -M do -s 8972 <ip_addr> is specifically used to verify Jumbo Frame configuration across the network.
The -M do flag sets the "Do Not Fragment" (DF) bit, meaning the network is not allowed to break the packet into smaller pieces.
The -s 8972 flag sets the ICMP data payload to 8972 bytes. When you add the standard 8-byte ICMP header and the 20-byte IP header, the total packet size equals exactly 9000 bytes.
If this ping command fails, it indicates that somewhere along the network path between the host (initiator) and the FlashArray (target), a switch port, router, or network interface is not configured to support an MTU of 9000. The packet is being dropped because it is too large and cannot be fragmented. The administrator must verify the MTU settings on every network hop (switches, routers, and host NICs) to resolve the issue.
Here is why the other options are incorrect:
Engage support to enable NVME/ TCP services (A): The failure of a Jumbo Frame ping test is a Layer 2/Layer 3 network configuration issue, not an indicator that the NVMe/TCP storage protocol service is disabled on the array.
Run the command from the target (C): While pinging from the FlashArray back to the host is a valid secondary troubleshooting step, it will likely also fail if the network path doesn't support Jumbo Frames. The actual resolution is to fix the MTU on the network hops.
NEW QUESTION # 64
What is the Pure Storage recommended Maximum Transmission Unit (MTU) size for the replication ports on a FlashArray?
Answer: B
Explanation:
Understanding MTU: The Maximum Transmission Unit (MTU) defines the largest size of a packet or frame that can be sent in a single network transaction. The standard Ethernet MTU is 1500 bytes. Anything larger than 1500 bytes is referred to as a Jumbo Frame.
Replication Efficiency: Replication involves moving large amounts of data between arrays. Using standard 1500-byte frames results in higher overhead because the CPU must process a larger number of headers for the same amount of data. By increasing the MTU, the FlashArray can pack more data into each frame, reducing CPU interrupts and improving overall throughput.
The Pure Recommendation: Pure Storage specifically recommends an MTU of 9000 for both iSCSI and Replication traffic. This is the industry standard for Jumbo Frames that balances efficiency with compatibility across most enterprise-grade switches.
Configuration Requirements: It is critical to remember that MTU must be configured end-to-end. For an MTU of 9000 to work on the replication ports:
The FlashArray replication ports must be set to 9000.
The network switches along the path (and any routers/ISLs) must support and be configured for at least 9000.
The target array's replication ports must also be set to 9000.
Why 9216 (Option A) is incorrect: While some switches support a "Baby Giant" or slightly larger MTU like 9216 to account for VLAN tagging overhead, Pure's internal and best practice documentation specifically points to 9000 as the standard setting for the array's interface.
NEW QUESTION # 65
What is the proper procedure for stopping asynchronous replication and in-progress transfers?
Answer: C
Explanation:
According to the official Pure Storage FlashArray Asynchronous Replication Configuration and Best Practices Guide, the proper and immediate method to halt an active, in-progress asynchronous replication transfer is by disallowing the protection group at the target.
When you navigate to the target FlashArray and disallow the specific Protection Group, Purity immediately breaks the replication authorization for that group. If there is an in-progress snapshot transfer occurring at that exact moment, the transfer is immediately stopped, and the partially transferred snapshot data is discarded on the target side.
Here is why the other options are incorrect:
Disabling the replication schedule (B): Toggling the replication schedule to "Disabled" only prevents future scheduled snapshots from being created and sent. It does not kill or interrupt a replication transfer that is already currently in progress.
Removing the volume member from a protection group (A): Modifying the members of a protection group updates the configuration for the next snapshot cycle. It does not actively abort the transmission of the current point-in-time snapshot that the array is already busy sending over the WAN.
NEW QUESTION # 66
......
Exam FlashArray-Storage-Professional is just a piece of cake if you have prepared for the exam with the helpful of VCEPrep's exceptional study material. If you are a novice, begin from FlashArray-Storage-Professional study guide and revise your learning with the help of testing engine. Exam FlashArray-Storage-Professional Brain Dumps is another superb offer of VCEPrep that is particularly helpful for those who want to the point and the most relevant content to pass exam. With all these products, your success is assured with 100% money back guarantee.
FlashArray-Storage-Professional Download Pdf: https://www.vceprep.com/FlashArray-Storage-Professional-latest-vce-prep.html