IT인증시험을 쉽게 취득하는 지름길은Itexamdump에 있습니다. Itexamdump의Juniper인증 JN0-352덤프로 시험준비를 시작하면 성공에 가까워집니다. Juniper인증 JN0-352덤프는 최신 시험문제 출제방향에 대비하여 제작된 예상문제와 기출문제의 모음자료입니다. Juniper인증 JN0-352덤프는 시험을 통과한 IT업계종사자분들이 검증해주신 세련된 공부자료입니다. Itexamdump의Juniper인증 JN0-352덤프를 공부하여 자격증을 땁시다.
| Section | Objectives |
|---|---|
| Topic 1: Network Services | - Basic multicast concepts - NAT concepts in Junos |
| Topic 2: Routing Protocols | - BGP fundamentals and policy control - IS-IS overview - OSPF configuration and troubleshooting |
| Topic 3: Operations and Troubleshooting | - Troubleshooting routing and switching issues - Junos CLI monitoring tools |
| Topic 4: Layer 2 Switching Technologies | - Spanning Tree Protocol (STP/RSTP/MSTP) - VLANs and trunking - Ethernet switching concepts |
| Topic 5: Routing Policy and Filtering | - Route filtering and preference control - Policy statements |
| Topic 6: High Availability | - VRRP configuration and behavior - Redundancy concepts in enterprise networks |
IT업계에 종사하시는 분은 국제공인 IT인증자격증 취득이 얼마나 힘든지 알고 계실것입니다. 특히 시험이 영어로 되어있어 부담을 느끼시는 분도 계시는데 Itexamdump를 알게 된 이상 이런 고민은 버리셔도 됩니다. Itexamdump의Juniper JN0-352덤프는 모두 영어버전으로 되어있어Juniper JN0-352시험의 가장 최근 기출문제를 분석하여 정답까지 작성해두었기에 문제와 답만 외우시면 시험합격가능합니다.
질문 # 183
You are creating an aggregated Ethernet bundle using LACP on your Juniper Networks EX Series device.
In this scenario, which statement is correct?
정답：B
설명：
IEEE 802.3ad LACP defines two distinct negotiation modes, active and passive, and the standard's fundamental requirement for successful negotiation is that at least one end of the point-to-point link must be configured in active mode; an actively configured device initiates LACPDU transmission on its own, while a passively configured device waits and only responds once it receives an LACPDU from its peer. If both ends of the bundle were left in passive mode simultaneously, neither side would ever initiate the exchange, and no negotiation - and therefore no functioning aggregated bundle - would ever occur; at least one active participant is therefore mandatory, though having both sides active (active-active) is also fully valid and is in fact the most common production deployment. Junos does not enable LACP automatically on aggregated Ethernet interfaces; unlike some competing platforms, LACP must be explicitly configured under the aggregated-ether-options lacp hierarchy, and specifying no LACP configuration at all results in a 'static' LAG that relies purely on physical link-state rather than any protocol negotiation - there is no implicit default active mode. There is likewise no requirement to configure differing LACP system priority values between the two peer switches; system priority is used only to determine which side of the link controls port selection during negotiation and has no bearing on whether the bundle can form. Both sides being mandatorily active is a stricter requirement than the actual standard specifies. Reference topics: Junos Enterprise Switching - Link Aggregation, LACP Active and Passive Mode Negotiation.
질문 # 184
You have two OSPF routers forming an adjacency. R1 has a priority of 32 and a router ID of
192.168.1.2. R2 has a priority of 64 and a router ID of 192.168.1.1. The routers were started at the same time and all other OSPF settings are the default settings.
Which statement is correct in this scenario?
정답：B
설명：
The router with the highest OSPF priority becomes the DR. In this case, R2 has a higher priority (64) compared to R1's priority (32). Hence, R2 will become the DR.
The router with the next highest priority becomes the BDR. Since R1 has the next highest priority after R2, R1 will become the BDR.
질문 # 185
Which command displays the output shown in the exhibit?
정답：A
설명：
This command shows the Ethernet switching table, which includes information about MAC addresses, their associated VLANs, and the interfaces they are learned on, similar to the output shown in your exhibit.
질문 # 186
You have configured a GRE tunnel. To reduce the risk of dropping traffic, you have configured a keepalive OAM probe to monitor the state of the tunnel; however, traffic drops are still occurring.
Referring to the exhibit, what is the problem?
정답：D
설명：
For GRE tunnel keepalive to function properly, the hold time should be set to at least twice the keepalive interval to ensure proper detection and recovery of the tunnel state. In the exhibit, both keepalive-time and hold-time are set to 10 seconds, which is not optimal. The hold-time should be at least double the keepalive-time value.
So, to fix the issue, you should configure the hold-time to be 20 seconds or more.
질문 # 187
You are asked to configure a redundant trunk group (RTG). Which two requirements would accomplish this task? (Choose two.)
정답：B,C
질문 # 188
......
Juniper인증 JN0-352시험을 패스해서 자격증을 취득하려고 하는데 시험비며 학원비며 공부자료비며 비용이 만만치 않다구요? 제일 저렴한 가격으로 제일 효과좋은Itexamdump 의 Juniper인증 JN0-352덤프를 알고 계시는지요? Itexamdump 의 Juniper인증 JN0-352덤프는 최신 시험문제에 근거하여 만들어진 시험준비공부가이드로서 학원공부 필요없이 덤프공부만으로도 시험을 한방에 패스할수 있습니다. 덤프를 구매하신분은 철저한 구매후 서비스도 받을수 있습니다.
JN0-352합격보장 가능 공부: https://www.itexamdump.com/JN0-352.html