Our professionals constantly keep testing our 93-Tall-Mass-Timber-Buildings vce dumps to make sure the accuracy of our exam questions and follow the latest exam requirement. We will inform our customers immediately once we have any updating about 93-Tall-Mass-Timber-Buildings Real Dumps and send it to their mailbox. The feedback of most customers said that most questions in our 93-Tall-Mass-Timber-Buildings exam pdf appeared in the actual test.
| Section | Objectives |
|---|---|
| Topic 1: Tall Mass Timber Building Code Provisions | - Type IV Construction
- Structural and Connection Requirements
|
>> 93-Tall-Mass-Timber-Buildings Actual Test Pdf <<
The 93-Tall-Mass-Timber-Buildings Exam Dumps are compiled by experienced experts, they are quite familiar with the development the exam and they are also the specialists of the field. Besides the price of t93-Tall-Mass-Timber-Buildings exam braindumps are reasonable, no matter you are students or employees, you can afford it. Pass guarantee and money back guarantee for failure of your exams. We also offer you free update for 365 days, the update version will send to your email automatically.
NEW QUESTION # 30
Periodic special inspection of sealants or adhesives as specified by the International Building Code Section
703.7 shall be conducted at which of the following locations?
Answer: C
Explanation:
IBC Section 703.7 requires sealant or adhesive to resist air passage at the abutting edges and intersections of mass timber building elements where those elements are required to be fire-resistance rated. Section 1705.20 then requires periodic special inspection where those prescribed sealants or adhesives are installed. Option C repeats that first required location accurately.
Option D is defective because the code requires sealing at an intersection between mass timber and another material only where both intersecting building elements are required to be fire-resistance rated. The phrase
"one or the other" materially weakens the condition. Option A is also too broad. A code-defined joint is not automatically subject to Section 703.7; fire-resistant joint systems are separately regulated by Section 715 and, where applicable, Section 1705.18.
Option B describes the exception in reverse. Sealant or adhesive need not be added under Section 703.7 where it is not a required component of the tested fire-resistance-rated assembly. When it is part of the listed or tested assembly, it must be installed accordingly, but that statement does not identify the primary location requested.
References/Topics: 2021 IBC Sections 703.7 and 1705.20; sealing of adjacent rated mass timber elements; periodic inspection.
NEW QUESTION # 31
Concealed spaces in a Type IV-C building must be protected with:
Answer: B
Explanation:
In Type IV-C construction, combustible construction forming concealed spaces must receive noncombustible protection providing an assigned time of at least 40 minutes. Consequently, option D is correct.
Type IV-C permits substantial portions of mass timber to remain exposed within occupied interior spaces, subject to the applicable construction and fire-resistance requirements. That permission does not extend unchanged into concealed spaces. Concealed combustible surfaces create a different hazard because fire can spread above ceilings, inside shafts, or within service cavities without immediate detection. Section 602.4.3.5 therefore imposes a specific 40-minute noncombustible protection requirement.
An NFPA 13 sprinkler system is generally required for tall mass timber buildings, but sprinkler protection alone is not the prescribed substitute for this concealed-space protection. Fire-retardant-treated wood is still combustible and does not constitute the required noncombustible protective membrane. Option C is also incorrect because the concealed-space rule is more specific than the provisions governing exposed surfaces in occupied spaces.
Inspection should occur before closure so that membrane continuity, board orientation, fastener spacing, joint treatment, penetrations, and protection around connection hardware can be fully observed.
References/Topics: 2021 IBC Sections 602.4.3.2 and 602.4.3.5; Table 722.7.1(1); concealed combustible construction in Type IV-C buildings.
NEW QUESTION # 32
One code-recognized method for calculating the fire-resistance rating of exposed wood members and decking is:
Answer: D
Explanation:
The intended answer is ANSI/AWC NDS Chapter 16. The video option uses "AWS," but the correct standards organization is the American Wood Council-AWC . Option D is therefore correct based on its intended reference.
IBC Section 722.1 expressly permits exposed wood members and wood decking to have their calculated fire resistance determined in accordance with Chapter 16 of the ANSI/AWC National Design Specification for Wood Construction. The method evaluates charring, the effective char depth, the reduced residual cross section, elevated-temperature effects, loading, and the remaining structural capacity for the required exposure period.
ACI 216.1 applies to concrete and masonry fire resistance. TMS 0216 addresses masonry assemblies. ASCE
29 Chapter 5 provides procedures for calculating the fire resistance of structural steel assemblies. Those references are code-recognized methods, but they apply to different construction materials.
For mass timber inspection, the approved calculations should identify the exposed surfaces, required rating, timber species or product, member dimensions, design loads, protective contribution, and connection treatment. Field reductions in member dimensions can invalidate the calculated fire resistance.
References/Topics: 2021 IBC Section 722.1; ANSI/AWC NDS Chapter 16; calculated fire resistance of exposed wood members and decking.
NEW QUESTION # 33
Refer to the exhibit by clicking on the EXHIBIT button above.
In the detail shown, which fasteners require fire protection according to AWC Technical Report 10?
Answer: D
Explanation:
The 1/2-inch lag screws attaching the structural steel ledger require fire protection, making option D correct. These fasteners are structural components of the ledger-to-CLT connection and therefore form part of the connection whose fire performance must be maintained for the required duration.
AWC Technical Report 10 states that wood structural connections-including their connectors, fasteners, and participating members-must be protected from fire exposure for the required fire-resistance time
. Protection may be provided by wood cover, fire-rated gypsum board, other approved materials, or a combination.
TR10 distinguishes structural connection fasteners from small fasteners used merely to hold sacrificial protection in place. The report specifically explains that fasteners attaching protective wood strips need not themselves be protected, provided they are sufficiently long to keep the protection in position throughout the required exposure.
In the illustrated ledger connection, the 1/2-inch lag screws transfer structural load between the steel ledger and CLT wall. Their thermal protection is therefore integral to maintaining connection capacity.
References/Topics: AWC Technical Report No. 10 Sections 4.5 and connection examples; thermal protection of structural connectors and fasteners.
NEW QUESTION # 34
Sealants used to resist passage of air in construction Type IV-A, shall be in accordance with which of the following standards?
Answer: C
Explanation:
ASTM C920 is the required standard for sealants used under the IBC mass timber air-sealing provision.
Option C is therefore correct. Section 703.7 applies to Type IV-A construction and requires compliant sealant or adhesive at specified interfaces involving fire-resistance-rated mass timber elements.
The sealing requirement reduces the movement of air, heat, and combustion gases into gaps that could expose additional timber surfaces and undermine the rated performance assumed by the approved design. The sealant must not merely appear to close the opening; it must be the specified product and installed within its approved joint dimensions and substrate conditions.
ASTM A36 is a structural steel material specification. ASTM E119 establishes procedures for fire testing building construction and assemblies but does not qualify elastomeric sealant products. ASTM F1667 covers driven fasteners such as nails, spikes, and staples and has no application to this sealing requirement.
Under Section 1705.20, installation is subject to periodic special inspection where the Section 703.7 sealant is applied. Inspection should occur before concealment and confirm continuity, adhesion, backing, joint depth, surface cleanliness, and compliance with the approved documents.
References/Topics: 2021 IBC Sections 703.7 and 1705.20; Type IV-A construction; ASTM C920.
NEW QUESTION # 35
......
If you want to pass your 93-Tall-Mass-Timber-Buildings exam, we believe that our learning engine will be your indispensable choices. More and more people have bought our 93-Tall-Mass-Timber-Buildings guide questions in the past years. These people who used our products have thought highly of our 93-Tall-Mass-Timber-Buildings Study Materials. If you decide to buy our products and tale it seriously consideration, we can make sure that it will be very easy for you to simply pass your exam and get the 93-Tall-Mass-Timber-Buildings certification in a short time.
93-Tall-Mass-Timber-Buildings Dumps Torrent: https://www.validbraindumps.com/93-Tall-Mass-Timber-Buildings-exam-prep.html