BONUS!!! Download part of Lead1Pass NS0-185 dumps for free: https://drive.google.com/open?id=1JYPcgSg_KZefZAs6a3TbjH4pQSxaTmzM
If you are having the same challenging problem, don't worry; Network Appliance is here to help. Our direct and dependable Network Appliance Treasury with NetApp Storage Installation Engineer, ONTAP Professional Exam Exam Questions in three formats will surely help you pass the Network Appliance Treasury with NS0-185 certification exam. Because this is a defining moment in your career, do not undervalue the importance of our Treasury with NetApp Storage Installation Engineer, ONTAP Professional Exam (NS0-185) exam dumps. Profit from the opportunity to get these top-notch exam questions for the NS0-185 certification test.
| Section | Objectives |
|---|---|
| ONTAP Networking | - Cluster networking configuration - Network types in ONTAP clusters |
| Basic Installation Topics and Tools | - Installation preparation tools and documentation - Physical cabling of ONTAP nodes |
| ONTAP Switches | - Switched cluster cabling - Switch configuration software requirements |
| ONTAP Configuration | - Add or remove cluster nodes - Installation troubleshooting support tools - Cluster peering setup - Security hardening |
| ONTAP Concepts | - Aggregate creation - Cluster installation and expansion - Cluster controller components - ONTAP updates and version management |
| Customer Handoff | - Customer delivery and handoff - Installation validation tools - Documentation creation |
One of the most effective strategies to prepare for the NetApp Storage Installation Engineer, ONTAP Professional Exam (NS0-185) exam successfully is to prepare with actual Network Appliance NS0-185 exam questions. It would be difficult for the candidates to pass the NS0-185 exam on the first try if the NS0-185 study materials they use are not updated. Studying with invalid NS0-185 practice material results in a waste of time and money. Therefore, updated NS0-185 practice questions are essential for the preparation of the NetApp Storage Installation Engineer, ONTAP Professional Exam (NS0-185) exam.
NEW QUESTION # 34
A customer has a 2-node FAS8200 cluster with four DS212C shelves with 10 TB SATA drives.
Referring to the exhibit, an aggregate will be created with which default RAID type?
Answer: A
Explanation:
ONTAP 9.x defaults toRAID-DPfor SATA, NL-SAS, SAS, and SSD aggregates unless specific conditions require RAID-TEC. RAID-DP provides double-parity protection, allowing the system to withstand two simultaneous disk failures, which is essential for large-capacity SATA drives such as 10 TB disks.
RAID-TEC is reserved for very large aggregates with higher disk counts and is not the default. RAID4 and RAID1 are not used as default aggregate RAID types in ONTAP 9.
Therefore, the aggregate will be created withRAID-DP.
NEW QUESTION # 35
You are installing a new six-node ONTAP 9.8 cluster. You have completed the initial configuration of the cluster interconnect switches and the ONTAP cluster.
In this scenario, which feature should you enable?
Answer: D
Explanation:
After completing the initial configuration of a multi-node ONTAP cluster and its cluster interconnect switches, NetApp installation best practices require enabling proactive monitoring of the cluster network. The Cluster Switch Health Monitor (CSHM)is the ONTAP feature designed specifically for this purpose.
CSHM continuously monitors the health of supported cluster switches by collecting information such as switch configuration, port status, firmware versions, cabling, and error conditions. It validates this information against NetApp-supported configurations and best practices. When deviations or risks are detected, CSHM generates alerts and EMS messages that allow administrators to take corrective action before cluster communication is affected.
Cluster switch logging alone does not provide health analysis or proactive validation; it only records switch events. IPv6 is not required or recommended for cluster interconnect networks in standard ONTAP installations. Data Center Bridging (DCB) is used for specific Ethernet storage protocols and is not applicable to ONTAP cluster interconnect networks.
Therefore, enabling thecluster switch health monitoris the correct and required post-installation step.
NEW QUESTION # 36
After the installation of a new ONTAP 9.8 cluster, you have to verify if AutoSupport works. In this scenario, which two commands would you use to accomplish this task? (Choose two.)
Answer: B,D
Explanation:
https://docs.netapp.com/us-en/ontap-cli-93/system-node-autosupport-history- show.html#description
NEW QUESTION # 37
You are preparing to install a new clustered Data ONTAP system.
Which tool prepares all the relevant customer and configuration information?
Answer: D
NEW QUESTION # 38
When planning disk layout, which two RAID configurations are commonly used in ONTAP to provide fault tolerance and ensure data availability?
Answer: C,D
Explanation:
RAID-DP and RAID-TEC provide dual and triple parity protection. RAID-0 lacks redundancy, and RAID-1 is not commonly used in ONTAP for aggregates.
NEW QUESTION # 39
......
You may be given the Network Appliance NS0-185 practice exam results as soon as they have been saved in the software. Lead1Pass modified Network Appliance NS0-185 exam dumps allow students to learn effectively about the real Network Appliance NS0-185 Certification Exam. Network Appliance NS0-185 practice exam software allows students to review and refine skills in a preceding test setting.
NS0-185 Certificate Exam: https://www.lead1pass.com/NetworkAppliance/NS0-185-practice-exam-dumps.html
P.S. Free 2026 Network Appliance NS0-185 dumps are available on Google Drive shared by Lead1Pass: https://drive.google.com/open?id=1JYPcgSg_KZefZAs6a3TbjH4pQSxaTmzM