Every applicant goal is to find success in the Juniper JN0-364 exam for the very first time. Candidates make an effort to study for the Juniper JN0-364 test and are looking for a platform that ensures they will pass the JN0-364 Exam on the first attempt. Candidates have fear of money and time loss because of using invalid Juniper JN0-364 practice test material.
| Section | Objectives |
|---|---|
| Topic 1: MPLS and Service Provider Technologies | - MPLS fundamentals
|
| Topic 2: Service Provider Architecture & Junos Fundamentals | - Junos OS routing fundamentals
|
| Topic 3: OSPF and IS-IS Routing Protocols | - OSPF configuration and troubleshooting
|
| Topic 4: Troubleshooting and Operations | - Network troubleshooting methodology
|
| Topic 5: BGP and Routing Policy | - BGP fundamentals
|
>> Reasonable JN0-364 Exam Price <<
It is universally acknowledged that JN0-364 certification can help present you as a good master of some knowledge in certain areas, and it also serves as an embodiment in showcasing one’s personal skills. However, it is easier to say so than to actually get the JN0-364 certification. We have to understand that not everyone is good at self-learning and self-discipline, and thus many people need outside help to cultivate good study habits, especially those who have trouble in following a timetable. Buy our JN0-364 Exam Questions, we will help you pass the JN0-364 exam without difficulty.
NEW QUESTION # 61
You are evaluating BGP between two Juniper routers and the BGP session is stuck in the Idle state.
What would cause this behavior?
Answer: B
Explanation:
The Idle state indicates that the BGP process is waiting to initiate a connection but cannot establish a TCP session with the configured peer. If the peer IP address is incorrect, the router attempts to connect to a non-existent or wrong neighbor, preventing the TCP session on port 179 from being established and keeping the BGP session in the Idle state.
NEW QUESTION # 62
Referring to the exhibit. Which two statements are correct about the information shown in the exhibit? (Choose two.)
Answer: A,D
Explanation:
The exhibit shows the output of the command show spanning-tree bridge, which provides information about the spanning tree status of the switch. From the output, we can see that the switch has a bridge ID different from the root ID, which implies that this switch is not the root bridge. The "Topology change initiator" field shows ge-0/0/14, which indicates that the last topology change occurred on this interface, and this is also the interface used to reach the root bridge.
NEW QUESTION # 63
Exhibit:
user@R2> show route 198.51.100.1
inet.0: 19 destinations, 19 routes (19 active, 0 holddown, 0 hidden)
Restart Complete
+ = Active Route, - = Last Active, * = Both
198.51.100.1/32 *[Static/5] 5d 21:02:26
> to 203.0.113.65 via ge-0/0/3.0
user@R2> show route 172.20.110.0/24
inet.0: 19 destinations, 19 routes (19 active, 0 holddown, 0 hidden)
Restart Complete
+ = Active Route, - = Last Active,
* = Both
172.20.110.0/24 *[Static/5] 10:43:01
> via gr-0/0/0.0
Referring to the exhibit, traffic destined to which network will be sent through the tunnel?
Answer: B
Explanation:
To determine which traffic is being sent through a tunnel in a Junos OS environment, an administrator must analyze the routing table output for the exit interface associated with each destination prefix. The provided exhibit shows the results of the show route command on routerR2for two specific destination networks.
In the first output, the destination198.51.100.1/32is an active static route. The next-hop information specifies that traffic for this address is sent to the gateway 203.0.113.65 via the interfacege-0/0/3.0. According to Juniper Networks interface naming conventions, the prefixge-denotes aGigabit Ethernetinterface, which represents a standard physical connection. Therefore, this traffic does not traverse a tunnel.
In the second output, the destination172.20.110.0/24is also an active static route. However, the next-hop for this network is listed asvia gr-0/0/0.0. In the Junos operating system, thegr-prefix explicitly identifies a Generic Routing Encapsulation (GRE) tunnel interface. GRE is a widely used protocol in service provider networks to encapsulate various network layer protocols over an IP backbone, effectively creating a virtual point-to-point link. Because the routing table has installed the route for 172.20.110.0/24 specifically via the gr- interface, all traffic destined for this network will be encapsulated and sent through the tunnel.
The other choices are incorrect for the following reasons:
* 203.0.113.65 (Option B):This is the next-hop IP address for the physical Gigabit Ethernet path; it is not a destination network directed to a tunnel.
* 0.0.0.0/0 (Option C):There is no information in the exhibit regarding a default route.
* 198.51.100.1/32 (Option D):As identified by thege-interface prefix in the exhibit, traffic for this destination is sent via a physical Ethernet link.
NEW QUESTION # 64
You are monitoring OSPF on a router and notice frequent state changes between Full and Down. Which condition would cause this behavior?
Answer: D
Explanation:
When troubleshooting OSPF in a service provider environment, distinguishing between "stuck" adjacencies and "flapping" adjacencies is the first step. A session that transitions frequently betweenFullandDown indicates that the relationship can be established successfully (meaning parameters match), but it cannot be maintained.
According to Juniper Networks documentation, the most common cause for a session to drop from Full to Down is the expiration of theDead Interval. If a router does not receive a Hello packet within the Dead Interval (usually 40 seconds), it tears down the adjacency. Aphysical interface flapping (Option A)is the primary trigger for this. If the physical link or the underlying transport (like a leased line or a microwave link) goes down even momentarily, the OSPF process immediately detects the interface failure, flushes the neighbors, and moves the state to Down. As soon as the interface comes back up, the routers perform the Hello exchange and reach the Full state again, creating the flapping cycle.
Analysis of other options:
* MTU Mismatch (Option D):This typically causes the adjacency to get "stuck" in theExchangeor ExStartstate. The routers can exchange small Hello packets, but when they try to send larger Database Description (DBD) packets that exceed the MTU, the packets are dropped, preventing the session from ever reaching "Full."
* Area ID Mismatch (Option C):This prevents the adjacency from even reaching theInitstate; the routers will never form a neighbor relationship.
* Route Preference (Option B):This affects which route is chosen for the forwarding table but has no impact on the OSPF neighbor state machine itself.
NEW QUESTION # 65
Which two statements ate correct about the community BGP attribute on a Junos device?
(Choose two.)
Answer: A,C
Explanation:
The community attribute in BGP is an optional transitive attribute. It is not mandatory for BGP operations, but when it is present, it should be passed unchanged to other BGP peers unless explicitly modified by a routing policy. The community attribute is used to group destinations in a certain way, often to apply routing policies to those destinations collectively.
NEW QUESTION # 66
......
With our Juniper JN0-364 study material, you'll be able to make the most of your time to ace the test. Despite what other courses might tell you, let us prove that studying with us is the best choice for passing your Juniper JN0-364 Certification Exam! If you want to increase your chances of success and pass your JN0-364 exam, start learning with us right away!
JN0-364 Valid Test Question: https://www.torrentvce.com/JN0-364-valid-vce-collection.html