There are so many saving graces to our NSEI_OTS_AR-7.6 exam simulation which inspired exam candidates accelerating their review speed and a majority of them even get the desirable outcomes within a week. Therefore, many exam candidates choose our NSEI_OTS_AR-7.6 Training Materials without scruple. For as you can see that our NSEI_OTS_AR-7.6 study questions have the advandage of high-quality and high-efficiency. You will get the NSEI_OTS_AR-7.6 certification as well if you choose our exam guide.
| Section | Objectives |
|---|---|
| Network access control | - Explain OT Ethernet concepts - Configure network segmentation schemas - Configure network access authentication |
| Monitoring and risk assessment | - Perform risk assessment and management - Create FortiAnalyzer event handlers - Analyze security reports from FortiAnalyzer |
| Network security | - Configure virtual patching - Configure automation - Configure security inspections for industrial protocols |
| Asset management | - Fortinet Security Fabric for an OT network - Explain OT standard and Fortinet compliance - Implement device detection on FortiGate and FortiNAC |
>> Fortinet NSEI_OTS_AR-7.6 Clear Exam <<
Are you satisfied with your present job? Are you satisfied with what you are doing? Do you want to improve yourself? To master some useful skills is helpful to you. Now that you choose to work in the IT industry, you must register IT certification test and get the IT certificate which will help you to upgrade yourself. What's more important, you can prove that you have mastered greater skills. And then, to take Fortinet NSEI_OTS_AR-7.6 Exam can help you to express your desire. Don't worry. Dumps4PDF will help you to find what you need in the exam and our dumps must help you to obtain NSEI_OTS_AR-7.6 certificate.
NEW QUESTION # 15
Refer to the exhibit.
A firewall policy page is shown. To improve the security of your OT network, you have configured a Supervisor profile in the firewall policies, as shown in the exhibit. However, a supervisor is reporting that he cannot ping PLC-1. What are the two reasons? (Choose two answers)
Answer: A,B
Explanation:
The correct answers are A and C .
Option A is correct because the study guide explains that with active authentication , FortiGate prompts the user only when they use "an acceptable login protocol." It states: "When you use only active authentication, if all possible policies that could match the source IP address have authentication enabled, then the user will receive a login prompt (assuming they use an acceptable login protocol)." A direct ping to PLC-1 uses ICMP , which is not the kind of login protocol used to trigger user authentication.
So the supervisor must first authenticate through a protocol such as HTTPS or Telnet , then the ICMP traffic can match the authenticated policy.
Option C is also correct because the exhibit shows policy ID 8 greyed out, meaning it is not enabled. That policy appears above the Supervisor_access (9) policy and allows broader access to PLC-1 , whereas policy 9 is limited to ALL_ICMP . The study guide explains that "Because the user has not yet authenticated, the user group aspect of the traffic does not match" and FortiGate continues searching for another complete match. In this case, with policy 8 disabled, the supervisor is left with only the ICMP rule, which cannot be used to perform the initial login step needed for active authentication.
Option B is not supported by the exhibit. Option D is incorrect because auth-on-demand always would force authentication prompts more aggressively, but the core problem here is that the user is trying to start with ICMP and the broader policy that could permit the initial authenticated access is disabled.
NEW QUESTION # 16
For the installation of your first FortiGate device, you want to minimize the impact in your OT network.
Therefore, you deploy it initially as an offline IDS. Which two statements about this deployment are correct?
(Choose two answers)
Answer: C,D
Explanation:
Deploying a FortiGate in offline IDS (also known as one-arm sniffer mode) is a common strategy in OT environments for several reasons found in the study guide:
* Priority of Availability : In OT, availability and safety are critically important and prioritized higher than in IT. An offline IDS minimizes impact because it does not sit in the direct path of production traffic.
* Network Sensor Role : In this mode, the FortiGate is connected to a mirror/SPAN port on a switch. It acts as a network sensor , receiving a copy of the traffic rather than having the traffic flow through it.
This confirms Statement A is correct and Statement D is incorrect.
* Passive vs. Active : The guide explicitly states that in OT environments, passive methods are preferred over active methods to avoid negatively impacting performance or causing process interruptions.
* Depth of Visibility : Even though the device is offline, you apply security profiles (such as IPS, Application Control, and Antivirus) to the sniffer interface. This allows the FortiGate to analyze the copied traffic and provide deep visibility into the OT assets and their behaviors. This confirms Statement B is correct.
* Detection vs. Prevention : An IDS (Intrusion Detection System) is passive ; it can detect threats but cannot reset connections or drop packets to block attacks. Therefore, it cannot block zero-day attacks, making Statement C incorrect.
NEW QUESTION # 17
Refer to the exhibit.
A partial Application Sensor profile is shown. When you apply this profile in firewall policy, which two statements are correct? (Choose two answers)
Answer: A,D
Explanation:
The correct answers are A and C . The study guide explains that "You can use application control signatures to detect OT protocols" and that application control provides "granular message type identification." In the exhibit, the Operational Technology application category is included in the Application Sensor profile, so OT application signatures are enabled in this profile.
Option C is also correct because the override table shows Modbus_Read.Holding.Registers = Allow and Modbus = Block . The study guide states that you can use specific granular application control signatures to allow a specific Modbus command and block all others , and it also shows that application control can identify read and write commands separately at message level. Therefore, Modbus write commands are blocked by this profile.
Option B is incorrect because the profile is not simply monitoring all OT protocols; it contains a Block action for Modbus. Option D is incorrect because the study guide links OT protocol visibility specifically to the monitor status , while in the exhibit Modbus_Read.Holding.Registers is set to Allow , not Monitor .
NEW QUESTION # 18
Refer to the exhibit.
A partial OT network is shown. You have configured the FortiGate device with VLANs to segment the OT network. The supervisor now wants to connect to the PLC from the Engineering Workstation. How can you allow access from the Engineering Workstation to the PLC? (Choose one answer)
Answer: D
Explanation:
The correct answer is D. You must configure a layer 3 switch .
The study guide explains that "Layer 2 devices can add or remove tags" but "cannot modify them." It then states that "A layer 3 device, such as a router or FortiGate, can modify the VLAN tag before routing the packet. This allows them to route traffic between VLANs." It also explicitly describes
"Router on a Stick" as "a way to allow routing between VLANs." Since the exhibit shows a layer-2 switch and the Engineering Workstation and PLC are placed in different VLANs, inter-VLAN communication requires layer-3 routing.
The other options do not solve this requirement. intra-switch-policy explicit/implicit applies to a software switch , where member interfaces are in the same broadcast domain and same subnet, not to routing between separate VLANs. forward domain IDs are used in transparent mode to confine broadcasts to specific broadcast domains; they do not provide inter-VLAN access. Therefore, to let the Engineering Workstation in one VLAN reach the PLC in another VLAN, you need a layer 3 routing function , which matches option D .
NEW QUESTION # 19
Refer to the exhibit.
You have configured event handlers on FortiAnalyzer to monitor your OT network.
Based on the partial Event Monitor page shown in the exhibit, which statement is correct?
Answer: A
Explanation:
The correct answer is D . The exhibit shows the IPS event with the status Mitigated . Fortinet defines a Mitigated event as one where the security risk has been blocked or dropped ; an IPS log whose action is block or drop is the explicit example given in the OT Security 7.6 study guide. A Contained status instead indicates that the risk source has been isolated, such as an antivirus quarantine action. An Unhandled status indicates that the risk remains open-for example, an IPS event where the action is pass. The Web.Client application-control entry in the exhibit has a blank status, so it cannot correctly be described as either Unhandled or Contained based solely on the displayed information. Therefore, the definitive conclusion from the Event Monitor is that the corresponding IPS action was block or drop .
NEW QUESTION # 20
......
We provide 1 year of free updates. In conclusion, Dumps4PDF guarantees that if you use the product, you will pass the NSEI_OTS_AR-7.6 exam on your first try. Its primary goal is to save students time and money, not just conduct a business transaction. Candidates can take advantage of the free trials to evaluate the quality and standard of the NSEI_OTS_AR-7.6 Dumps before making a purchase. With the right NSEI_OTS_AR-7.6 study material and support team passing the examination at first attempt is an achievable goal.
NSEI_OTS_AR-7.6 New Test Camp: https://www.dumps4pdf.com/NSEI_OTS_AR-7.6-valid-braindumps.html