誰もが良い仕事とまともな収入を望んでいます。しかし、彼らが優れた能力と優れた主要な知識を持っていない場合、彼らはまともな仕事を見つけるのは難しいです。テスト93-Tall-Mass-Timber-Buildings認定に合格すると、夢を実現し、満足のいく仕事を見つけることができます。 93-Tall-Mass-Timber-Buildings学習教材は、93-Tall-Mass-Timber-Buildings試験に簡単に合格するのに役立つ優れたツールです。時間をかけて学習する必要はありません。 93-Tall-Mass-Timber-Buildings試験ガイドは高品質であり、当社の製品を使用する場合、93-Tall-Mass-Timber-Buildings試験に合格する可能性は99％〜100％と非常に高くなっています。
| Section | Objectives |
|---|---|
| Topic 1: Tall Mass Timber Building Code Provisions | - Mass Timber Products and Definitions - Applicable Codes and References
|
>> 93-Tall-Mass-Timber-Buildings受験対策書 <<
最短時間で93-Tall-Mass-Timber-Buildings試験に合格すると、PassTestすべての受験者の声になります。 しかし、圧倒的な学習教材で最も価値のある情報を選択する方法は、すべての試験官にとって頭痛の種です。 絶え間ない努力の後、93-Tall-Mass-Timber-Buildings学習ガイドは誰もが期待するものです。 当社の専門家は、コンテンツを簡素化し、お客様の重要なポイントを把握するだけでなく、93-Tall-Mass-Timber-Buildings準備資料を簡単な言語に再コンパイルしました。レジャー学習体験と、今後の93-Tall-Mass-Timber-Buildings 試験93-Tall-Mass-Timber-Buildings合格できます。
質問 # 76
Which of the following construction Types permit concealed spaces to be protected by completely filling the concealed space with noncombustible insulation?
正解：B
解説：
Type IV-HT construction permits concealed spaces where those spaces comply with the specific protection alternatives prescribed for traditional heavy-timber construction. One permitted method is to completely fill the concealed space with noncombustible insulation. Therefore, option D is correct.
This provision should not be confused with the concealed-space requirements applicable to the tall mass timber classifications-Types IV-A, IV-B, and IV-C. Those classifications employ dedicated noncombustible protection and assigned-time requirements intended to control the contribution of concealed combustible construction during a fire. Type IV-HT follows a different concealed-space framework and allows protection through approved alternatives, including sprinkler protection, gypsum-board enclosure, or complete filling with noncombustible insulation, as applicable.
The insulation must completely occupy the concealed volume. Merely installing partial batt insulation, leaving unprotected voids, or relying on nominally fire-resistant thermal insulation does not satisfy the provision. The inspector should verify the material's noncombustibility, continuity, placement around obstructions, and conformance with the approved construction documents before the space becomes inaccessible.
References/Topics: 2021 IBC Section 602.4.4; concealed spaces in Type IV-HT construction; noncombustible insulation protection method.
質問 # 77
Refer to the exhibit by clicking on the EXHIBIT button above.
In the detail shown and according to AWC Technical Report 10, what is the time assigned in minutes to 5/8 in. Type X gypsum board for connection fire protection thermal separation requirements?
正解：A
解説：
For the illustrated two-layer protection system, the 5/8-inch Type X gypsum-board layer directly adjacent to the connection is assigned 20 minutes, while the second layer is assigned 40 minutes. Therefore, option C is correct.
The standard assigned protection time for one layer of 5/8-inch Type X gypsum board is 40 minutes.
However, the thermal-separation methodology applies a 0.50 reduction factor to the final or base Type X layer located directly against the protected connection. That layer therefore contributes 20 minutes. The outer layer retains its full 40-minute assigned value, producing a combined assigned protection time of 60 minutes for the two-layer configuration.
The layers are not interchangeable for calculation purposes because the reduced contribution applies specifically to the layer adjacent to the protected connection. Options A and B incorrectly assign the same value to both layers, while option D reverses the required allocation.
During inspection, the special inspector should verify layer sequencing, board thickness and type, fastening, joint staggering, edge support, protection at corners, and continuity around the connection. Missing or incorrectly sequenced layers can invalidate the calculated thermal-separation time.
References/Topics: AWC Technical Report 10; AWC 2021 Fire Design Specification Section 3.5.2.1; assigned protection time for Type X gypsum board.
質問 # 78
Which of the following is true regarding Type IV-B unprotected portions of mass timber ceilings and walls?
正解：B
解説：
Type IV-B construction is fundamentally protected mass timber construction, but the 2021 IBC permits specifically limited areas of interior mass timber to remain exposed. Section 602.4.2.2.2 establishes two independent exposure limits. Unprotected portions of mass timber ceilings, including attached beams, are limited to 20 percent of the floor area of the dwelling unit or fire area. Unprotected portions of mass timber walls, including attached columns, are limited to 40 percent of that floor area . Accordingly, option C correctly states the permitted percentages.
These percentages do not operate in isolation. Exposed areas must also comply with Section 602.4.2.2.4, which establishes separation requirements between unprotected mass timber surfaces. Where both walls and ceilings are exposed within the same dwelling unit or fire area, Section 602.4.2.2.3 requires use of the mixed- unprotected-area equation rather than independently maximizing both percentages.
Option A describes neither Type IV-B nor its controlled-exposure concept. Option B incorrectly characterizes Type IV-B as requiring complete encapsulation. Option D reverses the ceiling and wall percentages.
References/Topics: 2021 IBC Sections 602.4.2.2.2, 602.4.2.2.3 and 602.4.2.2.4; Type IV-B permitted exposed mass timber.
質問 # 79
Which of the following best describes the required protection for mass timber hoistway enclosure walls in Type IV-C construction?
正解：D
解説：
Type IV-C generally permits interior mass timber surfaces to remain exposed, but shaft and elevator hoistway enclosures are a specific exception to that broad exposure allowance. Section 602.4.3.6 requires shafts, elevator hoistways, and interior exit stairway enclosures constructed with mass timber to receive noncombustible protection having a minimum assigned protection time of 40 minutes . Option A is therefore correct.
Critically, protection is required on both the inside and outside of the shaft enclosure . The 40-minute value is an assigned contribution from the noncombustible protection; the complete enclosure must still satisfy whatever overall fire-resistance rating is required by Sections 713, 713.4, Table 601, or other applicable provisions.
Option B incorrectly applies the general Type IV-C exposed-interior allowance to a specifically regulated shaft condition. Option C is incomplete because 1/2-inch Type X gypsum board provides only 25 minutes under Table 722.7.1(2), not the required 40 minutes. A 5/8-inch Type X board provides a recognized 40- minute contribution when installed in accordance with Section 722.7.2. Option D does not state the prescribed Type IV-C shaft requirement.
References/Topics: 2021 IBC Sections 602.4.3.2 and 602.4.3.6; Tables 722.7.1(1) and 722.7.1(2).
質問 # 80
The building owner shall be responsible for each of the following for fire safety during construction except:
正解：B
解説：
Option C is not an IFC requirement. The 2021 IFC requires inspection records to be maintained on-site, but it does not require those records to be secured in a fire- and water-resistant safe.
Section 3303.2 requires the owner to designate a site safety director. Section 3303.3 then makes that director responsible for completing a daily fire safety inspection of the project site. Every day, building and outdoor construction areas must be evaluated against the prescribed fire-safety inspection items.
The results of each inspection must be documented and retained on-site until a certificate of occupancy has been issued . The records must also be immediately available at the site for presentation to the fire code official upon request. Options A, B, and D therefore accurately reflect the code requirements.
The daily inspection program covers practical hazards such as hot work, temporary heating, combustible debris, temporary electrical wiring, hazardous-material storage, fire apparatus access, hydrants, fire department connections, standpipe availability, and portable extinguishers.
For tall mass timber projects, this documentation is particularly important because substantial combustible construction may be present before permanent fire protection systems are complete.
References/Topics: 2021 IFC Sections 3303.2 and 3303.3; site safety director; daily fire-safety inspection and documentation.
質問 # 81
......
最近、International Code Council 93-Tall-Mass-Timber-Buildings試験に合格するのは重要な課題になっています。同時に、93-Tall-Mass-Timber-Buildings資格認証を受け入れるのは傾向になります。93-Tall-Mass-Timber-Buildings試験に参加したい、我々PassTestの93-Tall-Mass-Timber-Buildings練習問題を参考しましょう。弊社は1年間の無料更新サービスを提供いたします。あなたがご使用になっているとき、何か質問がありましたらご遠慮なく弊社とご連絡ください。
93-Tall-Mass-Timber-Buildings日本語版トレーリング: https://www.passtest.jp/International-Code-Council/93-Tall-Mass-Timber-Buildings-shiken.html