P.S. Free 2026 Versa Networks VNX301 dumps are available on Google Drive shared by Actual4Labs: https://drive.google.com/open?id=1zw7W6DZp0L8INWZ-fjD1OHrPWHk3rGuO
We have free update for 365 days after purchasing the VNX301 exam materials, and the updated version will be sent to your email automatically. With this, you can change your scheme according to the requirement of the exam center. In addition, VNX301 exam materials are high-quality and accurate. We have the professional experts to verify the VNX301 Exam Dumps at times, therefore the correctness can be guaranteed. We also have the online and offline service, and if you have any questions, just consult us.
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
| Topic 6 |
|
Questions of Versa Certified SD-WAN Specialist (VNX300) desktop practice exam software are similar to the actual VNX301 exam questions. This gives you a genuine feeling of being in an VNX301 exam atmosphere. This feature helps you become familiar with the VNX301 real test format and improves your ability to do well on the actual VNX301 exam.
NEW QUESTION # 35
A branch device is powered on with factory-default staging configuration. The device establishes an IKE session to the staging server and receives an IP address, but it does not proceed to establish an IKE session with the Versa Controller. Which staging phase is failing?
Answer: A
Explanation:
The correct answer is B . In Versa SD-WAN onboarding, the branch progresses through three staging phases.
In Stage 1 , the branch uses its factory-default configuration to start an IKE session with the staging server.
After the IKE session comes up, the staging server assigns an IP address to the branch and notifies the branch of the Versa Director IP address. Versa Director is also notified that the branch has come up.
In Stage 2 , Versa Director pushes the stage-two configuration to the branch through the staging server. This stage changes the IPsec profile so that the Controller IP address becomes the remote IP. The branch reboots and then attempts to establish the IKE session with the Controller. If the device successfully completed Stage
1 but never forms the Controller IKE session, the failure point is Stage 2.
Stage 3 is later, when the device receives stage-three configuration, becomes operational, and creates Controller IPsec plus branch-to-branch VXLAN/ESP sessions. Therefore, the described issue is a Stage
2 staging failure.
NEW QUESTION # 36
Examine the exhibit below.
As an administrator of a Versa Secure SD-WAN, you are asked to find the current bandwidth of each WAN circuit used for SD-WAN connectivity in a branch, but the Director is not displaying any information for the WAN circuits.
In this scenario, what should be done to get the graph populated for all WAN circuits?
Answer: D
Explanation:
The correct answer is B . The exhibit shows the branch interface summary in Versa Director with a Live Data column. To populate real-time bandwidth graphs for WAN circuits, the administrator must select Live Data for the WAN interfaces that need to be monitored. Versa monitoring documentation states that, from a Director node, you can monitor VOS devices and organizations, and that Director, together with Versa Analytics, can poll VOS devices in real time to understand what is happening on the devices. This real-time information can be displayed to assist with troubleshooting.
Because the question asks for the current bandwidth of each WAN circuit, historical analytics alone is not sufficient. The dashboard must poll live statistics from the selected WAN circuits. In the exhibit, not all WAN interfaces appear to have Live Data selected; therefore, the graph is not populated for all circuits. Refreshing the page does not enable polling and will not solve the missing data condition.
Selecting only MPLS would populate only the MPLS circuit, not all WAN circuits. Unselecting and reselecting only the INET circuit would affect only that one interface. Therefore, Live Data must be selected for all WAN circuits whose current bandwidth should be displayed.
NEW QUESTION # 37
A branch user reports poor throughput over an SD-WAN tunnel. The command show interfaces detail vni-0/0 shows the interface is operating at half-duplex / 100 Mbps , although the circuit is expected to run at 1 Gbps full duplex. What is the most likely cause?
Answer: A
Explanation:
The correct answer is C . Versa's bandwidth and throughput troubleshooting documentation specifically instructs administrators to check link speed and half-duplex conditions with the command show interfaces detail interface-name. The example output shows an interface operating at half-duplex / 100 Mbps , and the documentation states that the interface should not be in half-duplex mode and that 100 Mbps was incorrect in that scenario.
A duplex mismatch or incorrect negotiated speed can severely reduce effective throughput, cause collisions or retransmissions, and make SD-WAN overlay performance appear poor even when the overlay itself is functioning. Versa recommends fixing half-duplex and link-speed issues by correcting the configuration on the device to which the VOS device is connected and checking the ISP-side transmission mode, such as auto
/auto.
SLA probing, Controller route advertisement, and VXLAN encapsulation may affect SD-WAN path selection or tunnel formation, but the evidence in the question directly points to a physical or underlay Ethernet negotiation problem.
NEW QUESTION # 38
Examine the CLI output in the exhibit.
You are reviewing the OSPF adjacency on a VOS CPE, and the output is shown in the exhibit. In this scenario, what is the probable cause of the OSPF adjacency issue?
Answer: D
Explanation:
The correct answer is B . The exhibit shows the OSPF neighbor in the exst state, which means Exchange Start . Versa documentation lists the OSPF neighbor state codes and identifies exst as "exchange start," followed by exchange, loading, and full. In normal OSPF adjacency formation, neighbors progress through initialization and two-way communication before they negotiate database exchange. If the neighbor becomes stuck in ExStart or Exchange, a common and highly probable cause is an MTU mismatch between the two OSPF peers. During database description packet negotiation, the peers must agree on parameters that allow LSDB exchange; an MTU mismatch can prevent the adjacency from advancing to Full.
Option A is less likely because an area mismatch usually prevents the neighbor relationship from forming correctly rather than leaving it stuck in ExStart. Option C is also incorrect because the neighbor has already progressed beyond early states, which indicates that bidirectional communication has occurred. Option D is not the best answer because dropping OSPF multicast 224.0.0.5 would typically prevent discovery or keep the adjacency in an earlier state, not specifically in ExStart.
Therefore, the probable cause is an interface MTU mismatch.
NEW QUESTION # 39
What are three roles that VOS performs? (Choose three.)
Answer: C,D,E
Explanation:
The correct answers are A, B, and E . Versa Operating System, or VOS , is the software platform used for Versa SD-WAN branch and headend functions. Versa troubleshooting documentation explicitly refers to common runtime state across SD-WAN Controller, branch, and hub devices , confirming that VOS is used for Controller and branch-style SD-WAN roles. Versa monitoring documentation also lists SD-WAN branches, SD-WAN Controller nodes, SD-WAN hubs, vCPEs, and uCPEs as assets that are monitored and managed in Versa Director, which aligns with VOS being used as a branch/edge and controller platform.
VOS can also act as a uCPE platform . Versa documentation includes procedures to configure uCPE on a VOS device, showing that VOS can host or support uCPE deployment use cases.
The originally provided answer A, C, D is not correct. A Log Collector or log forwarder function belongs to the Versa Analytics architecture, not the VOS branch role; Versa's design guide states that the log forwarder is part of the Versa Analytics node or can run as a standalone log-forwarder server.
A Zookeeper arbiter is also not a standard VOS SD-WAN device role in this context.
NEW QUESTION # 40
......
Test your knowledge of the Versa Certified SD-WAN Specialist (VNX300) (VNX301) exam dumps with Actual4Labs Versa Certified SD-WAN Specialist (VNX300) (VNX301) practice questions. The software is designed to help with Versa Certified SD-WAN Specialist (VNX300) (VNX301) exam dumps preparation. Versa Networks VNX301 practice test software can be used on devices that range from mobile devices to desktop computers.
Related VNX301 Certifications: https://www.actual4labs.com/Versa-Networks/VNX301-actual-exam-dumps.html
What's more, part of that Actual4Labs VNX301 dumps now are free: https://drive.google.com/open?id=1zw7W6DZp0L8INWZ-fjD1OHrPWHk3rGuO