As the feefbacks from our worthy customers praised that our NSE6_FNC_AD-7.6 exam braindumps are having a good quality that the content of our NSE6_FNC_AD-7.6 learning quiz is easy to be understood. About some esoteric points, our experts illustrate with examples for you. Our NSE6_FNC_AD-7.6 learning quiz is the accumulation of professional knowledge worthy practicing and remembering, so you will not regret choosing our NSE6_FNC_AD-7.6 study guide.
| Section | Objectives |
|---|---|
| Topic 1: Network Visibility and Monitoring | - Explain and configure device profiling - Guests and contractors - Use logging options available on FortiNAC - Troubleshoot network devices and device status |
| Topic 2: Concepts and Initial Configuration | - Explain isolation networks and the configuration wizard - Model and organize infrastructure devices |
| Topic 3: Deployment and Provisioning | - Configure FortiNAC-F security policies - Configure security automation - Configure access control on FortiNAC-F - Configure and monitor high availability (HA) |
| Topic 4: Integration | - Configure and use FortiNAC-F Manager - Integrate with third-party devices using Syslog and SNMP trap input - Explain and configure MDM integration |
>> NSE6_FNC_AD-7.6 Top Exam Dumps <<
There is no reason to waste your time on a test. If you feel it is difficult to prepare for Fortinet NSE6_FNC_AD-7.6 and need spend a lot of time on it, you had better use Prep4away test dumps which will help you save lots of time. What's more, Prep4away exam dumps can guarantee 100% pass your exam. There is no better certification training materials than Prep4away dumps. Instead of wasting your time on preparing for NSE6_FNC_AD-7.6 Exam, you should use the time to do significant thing. Therefore, hurry to visit Prep4away.com to know more details. Miss the opportunity, you will regret it.
NEW QUESTION # 16
Refer to the exhibit. An administrator wants to use FortiNAC-F to automatically provision printers throughout their organization. Each building uses its own local VLAN for printers.
Which FortiNAC-F feature would allow this to be accomplished with a single network access policy?
Answer: C
Explanation:
The FortiNAC-F Logical Network feature is specifically designed to provide an abstraction layer between high-level security policies and the underlying physical network infrastructure. In large- scale deployments where different physical locations (like Building 1, 2, and 3 in the exhibit) use different local VLAN IDs for the same type of device (e.g., VLAN 10, 20, and 30 for printers), managing separate policies for each building would create significant administrative overhead.
By using a Logical Network, an administrator can create a single entity--for example, a logical network named "Printers"--and use it as the "Access Value" in a single Network Access Policy.
The mapping of this logical label to a specific physical VLAN occurs at the Model Configuration level for each network device. When a printer connects to a switch in Building 1, FortiNAC-F evaluates the policy, identifies that the printer should be in the "Printers" logical network, and checks the Model Configuration for that specific switch to see which VLAN ID is mapped to that label (VLAN 10). If the same printer moves to Building 3, the same single policy applies, but FortiNAC-F provisions it to VLAN 30 based on the local mapping for that building's switch.
This architectural approach ensures that policies remain consistent and easy to manage regardless of the complexity or variations in the local network topology.
"Logical Networks provide a way to define a network access requirement once and apply it across many different network devices that may use different VLAN IDs for that access... Each managed device can use different VLAN IDs for the same Logical Network label. You can define the Logical Networks based on requirements and then associate the network to a VLAN ID when the managed device is configured in the Model Configuration."
NEW QUESTION # 17
Refer to the exhibit. An administrator has configured the DHCP scope for a registration isolation network, but the isolation process isn't working.
What is the problem with the configuration?
Answer: A
Explanation:
In a FortiNAC-F deployment, the configuration of the DHCP scope for isolation networks (Registration, Remediation, etc.) must perfectly align with the underlying network infrastructure to ensure that isolated hosts can communicate with the FortiNAC appliance. In the provided exhibits, there is a clear discrepancy between the DHCP configuration and the Network Topology.
As shown in the "Network Topology" exhibit, the Registration Network resides on a router interface (or sub-interface) with the IP address 192.168.180.1. This address represents the default gateway for any host placed into the Registration VLAN. However, the "DHCP configuration" exhibit shows the scope "REG-ScopeOne" configured with a Gateway of
10.0.1.254. This 10.0.1.254 address belongs to the management/service network (port2 of FortiNAC), not the registration subnet. If a host in the Registration VLAN receives this incorrect gateway via DHCP, it will attempt to send all off-link traffic to an unreachable IP, preventing it from loading the Captive Portal or communicating with the FortiNAC server.
According to the FortiNAC-F Configuration Wizard Reference, when defining a Layer 3 network scope, the "Gateway" field must contain the IP address of the router interface that acts as the gateway for that specific isolation VLAN. The FortiNAC appliance itself usually sits on a different subnet, and traffic is directed to it via the router's DHCP Relay (IP Helper) and DNS redirection.
"When configuring scopes for a Layer 3 network, the Gateway value must be the IP address of the router interface for that subnet. This allows the host to reach its local gateway to route traffic.
If the gateway is misconfigured, the host will be unable to reach the FortiNAC eth1/port2 interface for registration... Ensure the Gateway matches the network topology for the isolation VLAN."
NEW QUESTION # 18
An administrator wants each department to create and manage its own contractor accounts but not be able to manage contractor accounts for other departments.
What must the administrator configure to limit the sponsor's capabilities?
Answer: B
Explanation:
The sponsor's administrative profile defines the scope of management permissions, including which accounts they can create, view, and modify. By restricting the administrative profile to a specific department, each sponsor can manage only their own department's contractor accounts and not those of other departments.
NEW QUESTION # 19
Which group type can have members added directly from the FortiNAC Control Manager?
Answer: C
NEW QUESTION # 20
While discovering network infrastructure devices, a switch appears in the inventory topology with a question mark (?) on the icon. What would cause this?
Answer: B
Explanation:
In FortiNAC-F, theInventory topologyuses specific icons to represent the status and model of discovered network infrastructure. When a switch or other network device is discovered via SNMP, FortiNAC-F retrieves itsSystem ObjectID (sysObjectID)to identify the specific make and model. This OID is then compared against the internal database of supported device mappings.
Aquestion mark (?)icon appearing on a discovered switch indicates that while the discovery process successfully communicated with the device (meaning SNMP credentials were correct), theSNMP ObjectID is not recognizedor mapped in the current version of FortiNAC-F. This essentially means the device is " unsupported " by the current software out-of-the-box. Because the OID is unknown, FortiNAC-F does not know which CLI or SNMP command set to use for critical functions like L2 polling (host visibility) or VLAN switching (enforcement). To resolve this, an administrator can manually " Set Device Mapping " to a similar existing model or a " Generic SNMP Device " if only basic L3 visibility is required.
" Discovered devices displaying a ' ? ' iconindicate the currently running version does not have a mapping for that device ' sSystem OID(device is not supported). Device mappings are used to manage the device by performing functions such as L2/L3 Polling, Reading, and Switching VLANs. " -Fortinet Technical Tip:
Options for devices unable to be modeled in Inventory.
NEW QUESTION # 21
......
Before you purchase our product you can have a free download and tryout of our NSE6_FNC_AD-7.6 study tool. We provide the demo on our pages of our product on the websites and thus you have an understanding of part of our titles and the form of our NSE6_FNC_AD-7.6 test torrent. After you visit the pages of our product on the websites, you will know the update time, 3 versions for you to choose. You can dick and see the forms of the answers and the titles and the contents of our NSE6_FNC_AD-7.6 Guide Torrent. If you feel that it is worthy for you to buy our NSE6_FNC_AD-7.6 test torrent you can choose a version which you favor.
NSE6_FNC_AD-7.6 Examcollection Free Dumps: https://www.prep4away.com/Fortinet-certification/braindumps.NSE6_FNC_AD-7.6.ete.file.html