If you are preparing for the Fortinet NSE 7 - FortiSASE 26 Architect (NSE7_SSE_AR-26) exam dumps our NSE7_SSE_AR-26 Questions help you to get high scores in your Fortinet NSE7_SSE_AR-26 exam. Test your knowledge of the Fortinet NSE 7 - FortiSASE 26 Architect exam dumps with Exam4Free Fortinet NSE7_SSE_AR-26 Practice Questions. The software is designed to help with NSE7_SSE_AR-26 exam dumps preparation.
| Section | Objectives |
|---|---|
| Topic 1: FortiSASE Architecture and Design | - SASE architecture concepts
|
| Topic 2: Operations and Administration | - Management
|
| Topic 3: Security and Troubleshooting | - Security operations
|
| Topic 4: Deployment and Configuration | - FortiSASE deployment
|
>> NSE7_SSE_AR-26 Free Study Material <<
The Fortinet Practice Test engine included with NSE7_SSE_AR-26 exam questions simulates the actual NSE7_SSE_AR-26 examinations. This is excellent for familiarizing yourself with the Fortinet NSE 7 - FortiSASE 26 Architect and learning what to expect on test day. You may also use the Fortinet NSE7_SSE_AR-26 online practice test engine to track your progress and examine your answers to determine where you need to improve on the NSE7_SSE_AR-26 exam.
NEW QUESTION # 22
An administrator is enforcing endpoint network lockdown using FortiSASE to ensure that devices access the internet only under defined security conditions. The lockdown state must be released automatically when the endpoint meets specific trust or connectivity criteria.
Which two conditions can trigger the release of the network lockdown on an endpoint? (Choose two answers.)
Answer: C,D
Explanation:
According to the FortiSASE 25 Enterprise Administrator Study Guide, page 88, FortiClient automatically exits network lockdown when the endpoint is detected as on-net or successfully establishes a FortiSASE tunnel.
Option A is correct: FortiSASE uses on-net detection rules to identify whether an endpoint is connected to a trusted corporate network. When the endpoint satisfies the configured on-net rules, FortiClient can release network lockdown because internet traffic can be protected by the organization ' s on-premises security infrastructure, such as FortiGate.
Option B is correct: Network lockdown prevents unrestricted LAN and internet access when an off-net endpoint fails to establish its required FortiSASE tunnel within the configured grace period. Once the tunnel is successfully established, FortiClient releases the lockdown, allowing internet traffic to be secured through FortiSASE.
Option C is incorrect: Rebooting the endpoint does not independently satisfy either release condition.
FortiClient continues enforcing the configured security requirements.
Option D is incorrect: Security posture tags evaluate endpoint compliance and support conditional access policies. However, posture compliance alone is not identified as a network-lockdown release condition.
The two documented release conditions are on-net detection and successful FortiSASE tunnel establishment.
Exact Source References:
* FortiSASE 25 Enterprise Administrator Study Guide, page 86 - On-Net Rule Sets.
* FortiSASE 25 Enterprise Administrator Study Guide, page 88 - On-Net and Off-Net Features- Network Lockdown.
* FortiSASE-Sovereign 26.2.a Administration Guide, page 67 - On/Off-Net Settings.
NEW QUESTION # 23
You want to configure two static routes. One that references a zone and the second one that references an SD- WAN member that belongs to that zone.
Which statement about this scenario is true?
Answer: B
Explanation:
FortiOS supports static routing through both SD-WAN zones and individual SD-WAN member interfaces.
However, a specific routing restriction applies when both types of routes are configured.
Option B is correct because FortiOS does not permit duplicate destination prefixes when one static route references an SD-WAN zone and another references an individual interface belonging to that zone.
Although identical destination prefixes are not permitted in this configuration, overlapping subnets with different prefix lengths are supported.
For example:
SD-WAN zone route: 10.0.0.0/8
Individual member route: 10.2.0.0/16
Both routes can coexist because their destination prefixes are different, despite overlapping address ranges.
FortiGate applies longest-prefix matching when determining the most specific destination route.
Option A is incorrect because FortiOS explicitly supports SD-WAN zones as static-route interfaces.
Option C is incorrect because static routes can reference individual SD-WAN members, providing more granular routing control.
Option D is incorrect because overlapping destinations are permitted but not mandatory. The essential requirement is that the zone route and individual member route must not use identical destination prefixes.
When a static route references an SD-WAN zone, FortiOS installs corresponding routes for the eligible zone members. These routes can participate in equal-cost multipath routing.
References: Fortinet SD-WAN 7.6 Core Administrator Study Guide, pages 192-193, Routing and Sessions; FortiOS 7.6 Administration Guide - SD-WAN Members and Zones .
NEW QUESTION # 24
An administrator configures the performance service-level agreement (SLA) with the probe mode, Prefer Passive.
What are two observable impacts of this configuration? (Choose two.)
Answer: A,C
Explanation:
FortiGate provides three primary SD-WAN health-monitoring modes: Active, Passive, and Prefer Passive.
Prefer Passive combines live-session measurements with active probes when sufficient application traffic is unavailable.
Option B is correct because FortiGate measures performance passively when qualifying TCP sessions traverse an SD-WAN member. It derives latency, jitter, and packet-loss measurements from actual TCP session behavior rather than relying exclusively on synthetic probes.
Option E is correct because passive measurements alone cannot reliably determine whether an otherwise idle interface is completely unreachable. In Prefer Passive mode, FortiGate uses active probing when no suitable TCP traffic has been observed for three continuous minutes. Active probes can then identify dead members.
Option A is incorrect because ordinary ICMP traffic does not provide the TCP session information required for this passive measurement mechanism.
Option C reverses the transition logic. The three-minute timer applies to the absence of TCP traffic before switching from passive to active monitoring. FortiGate returns to passive monitoring when eligible TCP traffic becomes available.
Option D is incorrect because enabling passive-wan-health-measurement disables automatic ASIC offloading for the affected firewall policy, allowing the CPU to observe the session characteristics necessary for passive measurement.
References: FortiOS 7.6 Administration Guide - Passive WAN Health Measurement and Performance SLA Overview; Fortinet Technical Tip - Different Types of Health Checks Used in SD-WAN.
NEW QUESTION # 25
Refer to the exhibit. You update the spokes configuration of an existing auto-discovery VPN (ADVPN) topology by adding the parameters shown in the exhibit. Which is a valid objective of those settings? Choose one answer.
Exhibit 1
Answer: D
Explanation:
The exhibit shows the following IPsec phase1-interface configuration applied on spoke tunnels: In the FCSS SD-WAN 7.6 ADVPN architecture, the network-overlay and network-id parameters are used to logically group IPsec tunnels into separate overlays. When network-overlay is enabled, FortiGate treats the tunnel as part of an overlay network rather than a simple transport tunnel. The network-id parameter is critical in multi- overlay ADVPN designs. Fortinet documentation specifies that ADVPN shortcuts are only allowed between tunnels that share the same network-id. This mechanism explicitly prevents cross-overlay shortcuts, ensuring that shortcuts are formed only within the same logical overlay and not across different overlays that may serve different purposes (for example, different hubs, regions, or transport groups). The use of auto-discovery- shortcuts dependent further enforces correct shortcut behavior by ensuring that shortcut tunnels depend on the state of the parent overlay tunnel, but it does not by itself prevent multiple shortcuts or convert ADVPN versions. Why the other options are incorrect: Therefore, the valid objective of these settings is to prevent cross-overlay shortcuts, which corresponds to Option C.
References: https://docs.fortinet.com/document/fortigate/latest/sd-wan-sd-branch-architecture-for-mssps
/704416/advpn-2-0; https://docs.fortinet.com/document/fortigate/7.6.0/cli-reference/838040159/config- system-sdwan
NEW QUESTION # 26
When designing a dual-hub SD-WAN architecture with FortiSASE, which two factors should be considered to ensure redundancy? (Choose two.)
Answer: C,D
Explanation:
Redundant dual-hub designs typically use BGP attributes such as local preference to influence primary versus backup hub selection, while SD-WAN rules referencing both overlay interfaces allow automatic failover based on link performance and route availability.
NEW QUESTION # 27
......
Our NSE7_SSE_AR-26 practice questions are specialized in providing our customers with the most reliable and accurate exam guide and help them pass their exams by achieve their satisfied scores. With our NSE7_SSE_AR-26 study materials, your exam will be a piece of cake. We have a lasting and sustainable cooperation with customers who are willing to purchase our actual exam. We try our best to renovate and update our NSE7_SSE_AR-26 learning guide in order to help you fill the knowledge gap during your learning process, thus increasing your confidence and success rate.
New NSE7_SSE_AR-26 Exam Notes: https://www.exam4free.com/NSE7_SSE_AR-26-valid-dumps.html