It is similar to the NSEI_OTS_AR-7.6 desktop-based software, with all the elements of the desktop practice exam. This NSEI_OTS_AR-7.6 exam can be accessed from any browser and does not require installation. The NSEI_OTS_AR-7.6 questions in the mock test are the same as those in the real exam. And candidates will be able to take the web-based NSEI_OTS_AR-7.6 Practice Test immediately through any operating system and browsers.
| Section | Objectives |
|---|---|
| Topic 1: Network Security | - Configure automation - Configure security inspections for industrial protocols - Configure virtual patching |
| Topic 2: Monitoring and Risk Assessment | - Analyze security reports from FortiAnalyzer - Perform risk assessment and management - Create FortiAnalyzer event handlers |
| Topic 3: Network Access Control | - Configure network access authentication - Explain OT Ethernet concepts - Configure network segmentation schemas |
| Topic 4: Asset Management | - Use Fortinet Security Fabric for an OT network - Explain OT standards and Fortinet compliance - Implement device detection on FortiGate and FortiNAC |
>> Fortinet NSEI_OTS_AR-7.6 Free Sample <<
Being anxious for the exam ahead of you? Have a look of our NSEI_OTS_AR-7.6 training engine please. Presiding over the line of our NSEI_OTS_AR-7.6 practice materials over ten years, our experts are proficient as elites who made our NSEI_OTS_AR-7.6 learning questions, and it is their job to officiate the routines of offering help for you. And i can say no people can know the NSEI_OTS_AR-7.6 exam braindumps better than them since they are the most professional.
NEW QUESTION # 35
Refer to the exhibit.
A partial Incident Analysis page is shown. How was the 360-Degree Security Review OT report attached to the incident? (Choose one answer)
Answer: B
Explanation:
The study guide says playbooks are used to automate tasks such as running reports and creating/updating incidents . It also says that after a playbook is triggered, it flows through its configured tasks.
It further shows a sample playbook sequence where an event is detected, an incident is created , a report runs , and details are attached to the incident . That is exactly the kind of workflow shown in the incident analysis view.
By contrast, the study guide says event handlers generate events when logs match configured rules. Event handlers are for detection, not for attaching reports to incidents.
NEW QUESTION # 36
You want to automate some tasks in your OT network. Which three configurations are directly available in a new basic event handler on FortiAnalyzer? (Choose three answers)
Answer: A,D,E
Explanation:
According to the OT Security 7.6 Architect study guide regarding FortiAnalyzer Event Management :
* Notification Options : When configuring a new event handler, FortiAnalyzer provides several built-in notification methods to alert administrators when specific log criteria are met. The most common and direct method is Send alert email (Option A).
* Incident Management : To streamline the SOC workflow, an event handler can be configured to Automatically create an incident (Option D) based on the triggered event. This moves the event into the Incident Manager for further analysis.
* Security Fabric Integration : In the 7.6 architecture, event handlers can directly trigger an Automation stitch (Option E). This allows the FortiAnalyzer to notify the root FortiGate to take action (like running a CLI script or changing a policy) across the Security Fabric.
* Exclusions : Create a report (Option B) is typically a task performed by a Playbook or a scheduled report job, not a direct setting inside the basic event handler configuration. Quarantine an attacker (Option C) is an action that results from an automation stitch or playbook, but it is not a direct configuration toggle within the event handler itself.
NEW QUESTION # 37
Refer to the exhibit.
A partial Application Sensor profile is shown. When you apply this profile in firewall policy, which two statements are correct? (Choose two answers)
Answer: B,C
Explanation:
The correct answers are A and C . The study guide explains that "You can use application control signatures to detect OT protocols" and that application control provides "granular message type identification." In the exhibit, the Operational Technology application category is included in the Application Sensor profile, so OT application signatures are enabled in this profile.
Option C is also correct because the override table shows Modbus_Read.Holding.Registers = Allow and Modbus = Block . The study guide states that you can use specific granular application control signatures to allow a specific Modbus command and block all others , and it also shows that application control can identify read and write commands separately at message level. Therefore, Modbus write commands are blocked by this profile.
Option B is incorrect because the profile is not simply monitoring all OT protocols; it contains a Block action for Modbus. Option D is incorrect because the study guide links OT protocol visibility specifically to the monitor status , while in the exhibit Modbus_Read.Holding.Registers is set to Allow , not Monitor .
NEW QUESTION # 38
Refer to the exhibit.
A Virtual Patching profile is shown. You have recently updated your SCADA system and would like to apply the SCADA virtual patching profile. Which two statements about this profile are correct? (Choose two answers)
Answer: A,B
Explanation:
The correct answers are B and D .
Option B is correct because the profile has Medium , High , and Critical selected, while Low severity is not selected. That means low-severity virtual patching signatures are not enforced by this profile. So for the device with MAC address 12:12:12:12:12 , low-severity signatures are not blocked. The study guide explains virtual patching as device-specific protection where "FortiGate caches the signatures and mitigation rules that apply to each device" and applies them when the related traffic matches the firewall policy.
Option D is correct because the Virtual Patching Exemptions table shows a row with the MAC address 11:
11:11:11:11 and no specific signature listed. The study guide states that in the Virtual Patching profile you can "Exempt a specific device with the MAC address or a specific signature." A MAC-only exemption means that specific device is excluded from virtual patching enforcement, so in practical terms it is treated as having no applicable vulnerabilities in this profile.
Option C is incorrect because the profile does not block critical signatures for all devices. The exemptions list proves that at least one device can be excluded by MAC address, and a specific signature can also be exempted. Therefore, enforcement is not universal across all devices.
Option A is incorrect because the entry Schneider.Electric.ClearSCADA.HTTP.Interface.XSS appears as a specific signature exemption , not as the only remaining vulnerability. The profile display is showing exemptions, not a statement that only one vulnerability is still present.
NEW QUESTION # 39
What are two advantages provided by industrial Ethernet? (Choose two answers)
Answer: B,D
Explanation:
The correct answers are B. Real-time control and D. Determinism . The study guide defines industrial Ethernet as the "use of Ethernet and TCP/IP as transport mechanisms for industrial protocols" and states that it provides "real-time control," "low latency," and "determinism (meaning reliable and predictable data delivery)" in harsh environments. It further explains that industrial Ethernet "provides deterministic communication between machine controllers, actuators, sensors, and other units." These statements directly confirm that the two key advantages are real-time control and determinism.
The other options are not supported by the study guide as core advantages of industrial Ethernet. Encryption is not listed as one of the benefits in this section, and remote access is discussed elsewhere in the OT architecture but not as a defining advantage of industrial Ethernet itself. The guide is explicit that the main benefits here are predictable delivery and real-time communication, which are essential in industrial control environments where timing and reliability matter.
NEW QUESTION # 40
......
Our NSEI_OTS_AR-7.6 study materials will provide you with 100% assurance of passing the professional qualification exam. We are very confident in the quality of NSEI_OTS_AR-7.6 guide torrent. Our pass rate of NSEI_OTS_AR-7.6 training braindump is high as 98% to 100%. You can totally rely on our NSEI_OTS_AR-7.6 Practice Questions. We have free demo of our NSEI_OTS_AR-7.6 learning prep for you to check the excellent quality. As long as you free download the NSEI_OTS_AR-7.6 exam questions, you will satisfied with them and pass the NSEI_OTS_AR-7.6 exam with ease.
NSEI_OTS_AR-7.6 New Real Test: https://www.suretorrent.com/NSEI_OTS_AR-7.6-exam-guide-torrent.html