Unsere Webseite ZertSoft ist eine Webseite mit langer Geschichte, die Zertifizierungsantworten zur API API-SIEE Prüfung bietet. Nach langjährigen Bemühungen beträgt die Bestehensrate der API API-SIEE Zertifizierungsprüfung bereits 100%. Der Inhalt unserer Lehrbücher aktualisieren sich ständig, damit die Schulungsunterlagen zur API API-SIEE Zertifizierungsprüfung immer korekkt sind. Darüber hinaus können Sie einjährige Aktualisierung genießen, wenn Sie unsere Dumps gekauft haben.
| Section | Objectives |
|---|---|
| Topic 1: Source Inspection Performance | - Report Writing Nonconformance and Deviations - Inspector Conduct and Safety - Review of Project Documents |
| Topic 2: Electrical Induction Motors | - Design and Construction Standards - Materials of Construction - Motor Testing |
| Topic 3: Electrical Inspection Tools and Test Equipment | |
| Topic 4: Switchgear Low and Medium Voltage | - LV AC Switchgear Grounding - Housing Frames and Enclosure Compartment - Wiring - Ratings Interlocks - Bus Compartment - Metering - Switchgear Section Compartments - Design and Construction - Voltage Transformers - Electric Tie Breakers - LV Switchgear Grounding - Circuit Breakers - Control Power Transformers - Switchgear Compartment Doors - Current Transformers |
| Topic 5: Electrical Skid Mounted Equipment | - Equipment Grounding - Industry Codes and Standards - Materials of Construction - Electrical Equipment for Hazardous Classified Locations - Cable Support Systems - Purged and Pressurized Equipment in Classified Locations - AC Control Wiring |
| Topic 6: Liquid-Immersed Transformers | - Industry Codes and Standards - Design and Construction |
| Topic 7: Terms and Definitions | |
| Topic 8: Equipment Risk Assessment | - Development of Inspection and Test Plans - Report Review - Development of a Source Inspection Project Plan |
| Topic 9: Source Inspection Management Program | |
| Topic 10: Motor Control Centers Low to Medium Voltage | - Design and Construction Standards - Materials of Construction - Main Isolating Switch - Amp Capacity - Ground Bus - Circuit Breakers - Enclosures Types - Main Feeder Cable Entry Compartment |
| Topic 11: Examination Methods, Tools and Equipment | - Dimensional Inspections - Surface Preparation and Coatings Inspections - Visual Inspections - Typical Electrical Testing Techniques - Functional Testing |
>> API-SIEE Deutsche Prüfungsfragen <<
Heutzutage, wo IT-Branche schnell entwickelt ist, müssen wir die IT-Fachleuten mit anderen Augen sehen. Sie haben uns viele unglaubliche Bequemlichkeiten nach ihrer spitzen Technik geboten und dem Staat sowie Unternehmen eine Menge Menschenkräfte sowie Ressourcen erspart. Sie beziehen sicher ein hohes Gehalt. Wollen Sie gleich wie sie werden? Dann müssen Sie zuerst die API API-SIEE Zertifizierungsprüfung bestehen.
69. Frage
Machine vibration measurement using non contacting probes are taken:
Antwort: A
Begründung:
The correct answer isD. In rotating electrical equipment,non-contacting probesnormally refer toproximity probesthat are mounted in or at thebearing housingsto monitorshaft relative vibration. These probes do not touch the shaft; instead, they sense shaft motion relative to the bearing housing. In practice, radial vibration is usually monitored in thehorizontal and vertical directions, and where applicable axial movement is also monitored using an axial probe arrangement. That makes option D the only technically correct choice.
The other options are not consistent with standard vibration measurement practice. Measurements taken on thebaseplateorframeare generally made with contact sensors such as accelerometers or velocity pickups, not non-contacting probes. Option B is incorrect because vibration is not defined as being measured "on the shaft at 1.2 times the running speed" as a standard probe location criterion. The API guide includeselectric motors over 500 HPamong its covered equipment categories and emphasizessource inspection and quality surveillance activitiestied to applicable standards, testing, and verification during manufacture.
70. Frage
In addition to maximum rated voltage, manufacturer's name, trademark and AWG, which of the following markings is required for all conductors and cables?
Antwort: C
Begründung:
The correct answer isD. Wire type designator. In electrical inspection practice, conductor and cable identification markings are required so the inspector can verify that the installed or supplied cable matches the approved specification, intended service, insulation system, and voltage class. Standard conductor markings commonly include themanufacturer's name or trademark, conductor size such as AWG, voltage rating, and the cable or wire type designation. Thewire type designatoris essential because it identifies the insulation and use category of the conductor, such as whether it is a specific thermoplastic, thermoset, heat-resistant, wet- location, or other recognized type.
The other options are not universal marking requirements for all conductors and cables.NEC classis not a standard marking item in this context.Country of originmay appear for commercial or regulatory reasons but is not the fundamental conductor marking requirement being asked here.Batch or lot numbermay be used by manufacturers for traceability, but it is not the general required marking for all conductors and cables.
Therefore, the required marking that completes the list is thewire type designator.
71. Frage
What tool is designed to measure mechanical oscillations?
Antwort: A
Begründung:
The correct answer isD. Vibration Meter. A vibration meter is specifically intended to measuremechanical oscillations, usually in terms of displacement, velocity, or acceleration. In source inspection of large electrical equipment, especiallyelectric motors over 500 HP, vibration measurement is important because excessive vibration can indicate problems such as rotor imbalance, shaft misalignment, bearing defects, looseness, soft foot, resonance, or installation errors. Since the API source inspection guide covers surveillance and verification activities for major rotating electrical equipment, understanding the purpose of vibration- measuring instruments is directly relevant to factory testing, condition verification, and acceptance evaluation.
The other options are not correct for this function. Atachometermeasures rotational speed, not mechanical oscillation. Aspectroscopeis used for optical spectrum analysis and is unrelated to machinery vibration.
Anoscilloscopedisplays electrical waveforms and can show signals from sensors, but it is not the primary instrument designed specifically to measure machine vibration in routine inspection practice. Therefore, the best answer isVibration Meter, because it directly measures the mechanical oscillatory behavior of equipment.
72. Frage
Each source inspection assignment should have a detailed Inspection and Test Plan ITP which identifies the:
Antwort: B
Begründung:
The correct answer isD. AnInspection and Test Plan ITPis not just a schedule of inspection events. Its essential purpose is to definewhat inspection and test activities will be performedand theacceptance criteriathat will be used to determine whether the equipment, component, or fabrication step complies with the applicable requirements. In API source inspection practice, the ITP serves as the structured control document for surveillance at the vendor shop. It identifies inspection points, witness or hold points, required examinations, tests, record reviews, and the governing criteria from specifications, drawings, codes, standards, and purchase documents.
OptionCis incomplete because simply listing activities does not tell the inspector or purchaser how conformance will be judged. OptionAis only a scheduling detail, and optionBconcerns personnel, which may be documented elsewhere but is not the core function of the ITP.
For effective source inspection, the ITP must clearly link each planned verification activity to a measurable or documentable standard of acceptability. That is why the best answer isactivities to be performed and the acceptance criteria.
73. Frage
According to IEEE C57.12.00, a durable, metal, name plate shall be affixed to each transformer by the:
Antwort: B
Begründung:
The correct answer isA, manufacturer. IEEE C57.12.00 requires that each transformer be provided with adurable metal nameplateattached by themanufacturer. This requirement exists because the nameplate is a permanent identification and rating record for the transformer. It contains critical information such as manufacturer identity, serial number, kVA rating, voltage ratings, frequency, impedance, cooling class, temperature rise, and other essential design and operating data. Since this information originates from the transformer design and production records, responsibility for affixing the plate belongs to the manufacturer, not to the owner, purchaser, or inspector.
From an API source inspection perspective, the nameplate is an important verification point during final inspection. The source inspector checks that the plate is present, permanently attached, legible, and consistent with the approved data sheet, purchase order, drawings, and test records. A missing, incorrect, or improperly marked nameplate can create traceability problems and may result in nonconformance. Therefore, the correct party responsible for affixing the durable metal nameplate is themanufacturer, makingAthe verified answer.
74. Frage
......
Wenn Sie die Ziertifizierungsprüfung für API API-SIEE einmalig bestehen oder Ihre IT-Fähigkeiten erhöhen wollen, ist ZertSoft Ihre beste Wahl. Nach langjährigen Bemühungen beträgt die Bestehensrate derAPI API-SIEE Prüfung bereits 100%. Unsere Schulungsunterlagen zur API API-SIEE Prüfung enthalten vollständige und grenzlose Dumps, mit den Sie ganz einfach die API-SIEE Prüfung bestehen können.
API-SIEE Probesfragen: https://www.zertsoft.com/API-SIEE-pruefungsfragen.html