TrainingDump provides you with actual Juniper JN0-336 dumps in PDF format, Desktop-Based Practice tests, and Web-based Practice exams. These 3 formats of Security, Specialist (JNCIS-SEC) exam preparation are easy to use. This is a printable Juniper JN0-336 PDF dumps file. The Juniper JN0-336 Pdf Dumps enables you to study without any device, as it is a portable and easily shareable format, thus you can study Juniper JN0-336 dumps on your preferred smart device such as your smartphone or in hard copy format.
| Section | Objectives |
|---|---|
| Topic 1: Security Director (Junos Space) | - Management platform
|
| Topic 2: Identity-Aware Security Policies | - Identity concepts
|
| Topic 3: Intrusion Detection and Prevention (IDP) | - IDP concepts and architecture
|
| Topic 4: High Availability (HA) Clustering | - Chassis cluster operations
|
| Topic 5: Juniper Advanced Threat Prevention (ATP) Cloud | - ATP Cloud concepts
|
| Topic 6: IPsec VPN | - Operations and troubleshooting
|
| Topic 7: SSL Proxy | - SSL inspection concepts
|
>> Valid JN0-336 Test Forum <<
We offer a money-back guarantee if you fail despite proper preparation and using our product (conditions are mentioned on our guarantee page). This feature gives you the peace of mind to confidently prepare for your Security, Specialist (JNCIS-SEC) (JN0-336) certification exam. Our Juniper JN0-336 exam dumps are available for instant download right after purchase, allowing you to start your Security, Specialist (JNCIS-SEC) (JN0-336) preparation immediately.
NEW QUESTION # 58
Which statement regarding Juniper Identity Management Service (JIMS) domain PC probes is true?
Answer: C
Explanation:
Juniper Identity Management Service (JIMS) domain PC probes are used to map usernames to IP addresses in the domain security event log. This allows for the SRX Series device to verify authentication table information, such as group membership. The probes are triggered whenever a username to IP address mapping is not found in the domain security event log. By default, the probes are executed at 60-minute intervals.
NEW QUESTION # 59
A pair of branch SRX Series devices are booted up in cluster mode.
Referring to the exhibit, which statement is correct?
Answer: B
Explanation:
The correct answer is C. fxp0 or fxp1 on either device has an existing configuration. The exhibit shows each node reporting itself in hold state and the peer as lost under redundancy group 0. Juniper's chassis cluster troubleshooting documentation shows this same hold/lost symptom and states that when a node is in hold, it is not ready to operate in a chassis cluster. For branch SRX devices, when cluster mode is enabled, specific physical interfaces are automatically converted into fxp0 for out-of-band management and fxp1 for the HA control link. These interfaces cannot retain normal transit or standalone interface configuration. If the ports that become fxp0 or fxp1 already have configuration, the cluster can enter the hold/lost condition shown in the exhibit.
Option A is wrong because the output does not indicate a Junos version mismatch. Option B is wrong because hardware mismatch is not the symptom being shown. Option D is too specific: a factory-default configuration can cause this problem because it may include configuration on interfaces that become fxp0/fxp1, but the exhibit does not prove specifically that node1 alone is running factory-default configuration. The tested issue is the existing configuration on the interfaces reserved for chassis-cluster management/control. Reference topics: HA Clustering, chassis cluster hold/lost state, fxp0, fxp1, branch SRX cluster initialization.
NEW QUESTION # 60
Which two statements are correct about cluster components? (Choose two.)
Answer: A,B
Explanation:
The correct answers are A and B. In an SRX chassis cluster, the cluster ID identifies the chassis cluster itself, while the node ID identifies the individual SRX device inside that two-node cluster. Juniper states that a cluster is identified by a cluster-id value from 1 through 255, and that setting the cluster ID to 0 is equivalent to disabling clustering. Therefore, option A is correct and option C is wrong.
Option B is also correct because Juniper states that a cluster node is identified by a node ID specified as a number from 0 through 1. A normal SRX chassis cluster has two nodes: node0 and node1. The two devices must use the same nonzero cluster ID so they belong to the same cluster, but each device must use a different node ID so Junos can apply node-specific configuration, interface numbering, redundancy-group ownership, and management settings correctly. Option D is wrong because node IDs do not range from 1 through 255; that range applies to cluster IDs, not node IDs. Reference topics: HA Clustering, cluster ID, node ID, chassis cluster formation, node0/node1 identification.
NEW QUESTION # 61
A client has attempted communication with a known command-and-control server and it has reached the configured threat level threshold.
Which feed will the clients IP address be automatically added to in this situation?
Answer: D
Explanation:
Infected hosts are internal hosts that have been compromised by malware and are communicating with external C&C servers3. Juniper ATP Cloud provides infected host feeds that list internal IP addresses or subnets of infected hosts along with a threat level3. Once the Juniper ATP Cloud global threshold for an infected host is met, that host is added to the infected host feed and assigned a threat level of 10 by the cloud4. You can also configure your SRX Series device to block traffic from these IP addresses using security policies4.
NEW QUESTION # 62
You are troubleshooting unexpected issues on your JIMS server due to out of order event log timestamps.
Which action should you take to solve this issue?
Answer: A
Explanation:
To solve the issue of out of order event log timestamps on your JIMS server, you should enable time synchronization on the domain controllers. JIMS (Juniper Identity Management Service) is a Windows service that collects user, device, and group information from Active Directory domains or syslog sources and provides it to SRX Series devices and CSO for identity-based security policies. JIMS relies on the timestamps of the event logs generated by the domain controllers to track user logins, logouts, and IP address changes. If the domain controllers have different or inaccurate clocks, the event logs may have out of order or incorrect timestamps, which can cause JIMS to miss or misinterpret some events and affect its accuracy and performance. Therefore, you should ensure that all the domain controllers in your network are synchronized with a reliable time source, such as an NTP server or a Windows Time service. Reference: = Juniper Identity Management Service User Guide, Juniper Identity Management Service Feature Guide, Configure JIMS Collector to Get Microsoft Event Logs, Considerations for timestamps in centralized logging platforms
NEW QUESTION # 63
......
Getting the Security, Specialist (JNCIS-SEC) (JN0-336) certification is the way to go if you're planning to get into Juniper or want to start earning money quickly. Success in the Security, Specialist (JNCIS-SEC) (JN0-336) exam of this credential plays an essential role in the validation of your skills so that you can crack an interview or get a promotion in an Juniper company. Many people are attempting the Juniper JN0-336 test nowadays because its importance is growing rapidly.
Dumps JN0-336 Guide: https://www.trainingdump.com/Juniper/JN0-336-practice-exam-dumps.html