Juniper JN0-352덤프샘플문제체험 - JN0-352최신시험후기

Juniper인증 JN0-352시험이 너무 어려워 보여서 오르지못할 산처럼 보이시나요? 그건Itcertkr의 Juniper인증 JN0-352시험문제에 대비하여 제작한Juniper인증 JN0-352덤프가 있다는 것을 모르고 있기때문입니다. Juniper인증 JN0-352시험에 도전하고 싶으시다면 최강 시험패스율로 유명한Itcertkr의 Juniper인증 JN0-352덤프로 시험공부를 해보세요.시간절약은 물론이고 가격도 착해서 간단한 시험패스에 딱 좋은 선택입니다.

Juniper JN0-352 Exam Syllabus Topics:

SectionObjectives
Network Services- Basic multicast concepts
- NAT concepts in Junos
High Availability- VRRP configuration and behavior
- Redundancy concepts in enterprise networks
Operations and Troubleshooting- Junos CLI monitoring tools
- Troubleshooting routing and switching issues
Routing Policy and Filtering- Policy statements
- Route filtering and preference control
Routing Protocols- IS-IS overview
- BGP fundamentals and policy control
- OSPF configuration and troubleshooting
Layer 2 Switching Technologies- Ethernet switching concepts
- Spanning Tree Protocol (STP/RSTP/MSTP)
- VLANs and trunking

>> Juniper JN0-352덤프샘플문제 체험 <<

JN0-352최신시험후기 - JN0-352적중율 높은 덤프공부

Juniper JN0-352인증시험패스 하는 동시에 여러분의 인생에는 획기적인 일 발생한것이죠, 사업에서의 상승세는 당연한것입니다. IT업계종사자라면 누구나 이런 자격증을 취득하고싶어하리라고 믿습니다. 많은 분들이 이렇게 좋은 인증시험은 아주 어렵다고 생각합니다. 네 많습니다. 패스할확율은 아주 낮습니다. 노력하지않고야 당연히 불가능하죠.Juniper JN0-352시험은 기초지식 그리고 능숙한 전업지식이 필요요 합니다. 우리Itcertkr는 여러분들한테Juniper JN0-352시험을 쉽게 빨리 패스할 수 있도록 도와주는 사이트입니다. 우리Itcertkr의Juniper JN0-352시험관련자료로 여러분은 짧은시간내에 간단하게 시험을 패스할수 있습니다. 시간도 절약하고 돈도 적게 들이는 이런 제안은 여러분들한테 딱 좋은 해결책이라고 봅니다.

최신 JNCIS-ENT JN0-352 무료샘플문제 (Q190-Q195):

질문 # 190
You need to apply a Layer 2 firewall filter on a Juniper Networks EX Series Switch to block traffic from the source MAC address 00:12:34:56:00:07 entering the switch on ge-0/0/3. After committing the configuration, traffic from the MAC address still passes through. Referring to the exhibit, which statement is correct in this scenario?

정답:A

설명:
The intent of this filter is to match and discard traffic from one single, specific host MAC address, which requires the source-mac-address match condition to reference the complete, exact 48-bit address using an explicit /48 mask (or no mask at all, which Junos treats as an implicit full match) so that only that one precise address is matched. As configured, the term instead specifies a /40 mask on 00:12:34:56:00:07, meaning only the first 40 bits (the first five octets, 00:12:34:56:00) are actually significant to the match, while the sixth octet is effectively wildcarded across its full range; this produces an imprecise, overly broad match criterion rather than the single-host match the administrator intended, and is a common configuration mistake that undermines the predictability and correctness of MAC-based filtering. The lesson tested here is that source and destination MAC address match conditions in Junos firewall filters must be specified with the correct, deliberate, and explicit prefix length appropriate to the intended scope -- typically /48 for a single exact host -- rather than an arbitrary or miscalculated mask value. Firewall filters under family ethernet-switching are fully capable of matching on both source-mac-address and destination-mac-address, which rules out that option entirely. Layer 2 MAC-based filters function correctly on both access and trunk interface modes, so interface type is not a limiting factor here.
There is no indication in the exhibit that the filter's application direction (input versus output) is reversed.


질문 # 191
Which statement is correct about the IS-IS ISO NET address?

정답:D

설명:
An ISO NET address is a type of network address used by the IS-IS routing protocol. It identifies a point of connection to the network, such as a router interface, and is also called a Network Service Access Point (NSAP).
An ISO NET address consists of three parts: an area ID, a system ID, and a selector. The area ID identifies the IS-IS area to which the device belongs. The system ID uniquely identifies the device within the area. The selector identifies a specific service or function on the device, such as routing or management.
An ISO NET address must be unique for each device in the network, because it is used by IS-IS to establish adjacencies, exchange routing information, and compute shortest paths. If two devices have the same ISO NET address, they will not be able to communicate with each other or with other devices in the network. Therefore, it is important to assign different ISO NET addresses to each device in the network.


질문 # 192
You are creating an aggregated Ethernet bundle using LACP on your Juniper Networks EX Series device. In this scenario, which statement is correct?

정답:D

설명:
IEEE 802.3ad LACP defines two distinct negotiation modes, active and passive, and the standard's fundamental requirement for successful negotiation is that at least one end of the point-to-point link must be configured in active mode; an actively configured device initiates LACPDU transmission on its own, while a passively configured device waits and only responds once it receives an LACPDU from its peer. If both ends of the bundle were left in passive mode simultaneously, neither side would ever initiate the exchange, and no negotiation -- and therefore no functioning aggregated bundle -- would ever occur; at least one active participant is therefore mandatory, though having both sides active (active-active) is also fully valid and is in fact the most common production deployment. Junos does not enable LACP automatically on aggregated Ethernet interfaces; unlike some competing platforms, LACP must be explicitly configured under the aggregated-ether-options lacp hierarchy, and specifying no LACP configuration at all results in a 'static' LAG that relies purely on physical link-state rather than any protocol negotiation -- there is no implicit default active mode. There is likewise no requirement to configure differing LACP system priority values between the two peer switches; system priority is used only to determine which side of the link controls port selection during negotiation and has no bearing on whether the bundle can form. Both sides being mandatorily active is a stricter requirement than the actual standard specifies.


질문 # 193

Click the Exhibit button.
You have two routers on your network that are not able to establish BGP sessions.
Which two statements are correct in this scenario? (Choose two.)

정답:A,C

설명:
The diagnostic output explicitly states the root cause: the local router has only the inet6-unicast address family configured for this peer, while the remote router advertised inet-unicast and inet-vpn-unicast in its OPEN message, and BGP requires at least one common negotiated address family (NLRI type) between two peers for a session to remain established; with zero overlap between the two sides' configured families, the session is torn down immediately after the OPEN exchange, which is precisely why the peer state shows Active rather than Established. This confirms the mismatched-address-family statement directly and unambiguously from the exhibit's own Down reason and Detail reason fields. The diagnostic tool's own embedded Suggestion text goes further, explicitly advising the administrator to additionally verify that the local-address configured for the peer matches the remote router's configured neighbor address and vice versa - a secondary, commonly encountered condition in which mismatched or effectively duplicated/incorrect address bindings between the two sides' neighbor statements can independently prevent a session from completing correctly, even once the family mismatch is resolved. This is why address-configuration consistency between the peers is flagged as a second concern worth checking in this scenario. Nothing in the exhibit references NTP or time synchronization at all, nor does anything in the output reference authentication, an MD5 mismatch, or any related failure signature; both of those conditions would present through entirely different diagnostic messages than the one shown here. Reference topics: Junos Enterprise Routing - BGP, Address Family Negotiation and the show bgp diagnostics neighbor Command.


질문 # 194
Refer to Exhibit:

You have applied a firewall filter as an ingress filter on the ge-0/0/0 interface of your Juniper Networks EX Series Switch as shown in the exhibit. An external host sends an ICMP ping packet to the router.
Which statement is correct about how this packet is processed?

정답:C

설명:
Junos firewall filters evaluate terms sequentially from top to bottom, and a term is only terminal for a packet if its then clause contains an explicit terminating action such as accept, discard, reject, or next term without a match. The count and log actions used in track-icmp are non- terminating; they update statistics and generate a log entry but do not stop evaluation, so a matching ICMP packet falls through to the next term after being counted. The second term, allow- tcp-established, matches only TCP packets carrying the ACK or RST flags as defined by the tcp- established keyword; an ICMP echo request does not satisfy protocol tcp, so this term is skipped entirely and does not accept the packet. Evaluation therefore reaches the implicit catch-all term block-rest, which has no from conditions and matches every remaining packet, incrementing blocked-counter and discarding it. The net effect for the described ICMP ping is that icmp-counter is incremented by the first term, the packet is neither accepted nor rejected by the second term, and blocked-counter is incremented immediately before the packet is silently discarded by the final term. This layered-term behavior, where counting is independent of the accept/discard decision, is a frequently tested nuance of Junos firewall filter processing logic.


질문 # 195
......

취직을 원하시나요? 승진을 원하시나요? 연봉인상을 원하시나요? 무엇을 원하시든 국제적으로 인정받은 IT인증자격증을 취득하는것이 길입니다. Juniper인증 JN0-352시험은 널리 인정받는 인기자격증의 시험과목입니다. Juniper인증 JN0-352시험을 패스하여 자격증을 취득하면 소원이 이루어집니다. Itcertkr의Juniper인증 JN0-352덤프는 시험패스율이 높아Juniper인증 JN0-352시험준비에 딱 좋은 공부자료입니다. Itcertkr에서 덤프를 마련하여 자격증취득에 도전하여 인생을 바꿔보세요.

JN0-352최신시험후기: https://www.itcertkr.com/JN0-352_exam.html