P.S. Free & New NSE6_OTS_AR-7.6 dumps are available on Google Drive shared by Real4dumps: https://drive.google.com/open?id=1aNSR4GvBPb0YBDbqpmBxEmK6QkPSaLqx
New latest Fortinet NSE6_OTS_AR-7.6 valid exam study guide can help you exam in short time. Candidates can save a lot time and energy on preparation. It is a shortcut for puzzled examinees to purchase NSE6_OTS_AR-7.6 valid exam study guide. If you choose our products, you only need to practice questions several times repeatedly before the real test. Our products are high-quality and high passing rate, and then you will obtain many better opportunities.
| Section | Objectives |
|---|---|
| Deployment and Operational Best Practices | - Securing industrial communication protocols
|
| OT Security Fundamentals | - Industrial Control Systems (ICS) and SCADA concepts
|
| Network Segmentation and Access Control | - Segmentation strategies for industrial networks
|
| Monitoring, Detection, and Incident Response | - Threat detection in OT environments
|
| Fortinet OT Security Architecture | - Fortinet Security Fabric in OT environments
|
>> Guaranteed NSE6_OTS_AR-7.6 Success <<
If you face any problem while using the offline or online software Fortinet NSE 6 - OT Security 7.6 Architect (NSE6_OTS_AR-7.6) practice exam of Real4dumps, contact our customer service team. Our team of experts is available 24/7 for your assistance while using updated NSE6_OTS_AR-7.6 Exam Prep material. Many takers of the Fortinet NSE 6 - OT Security 7.6 Architect (NSE6_OTS_AR-7.6) practice test suffer from money loss because it introduces new changes in the content of the test.
NEW QUESTION # 42
For the installation of your first FortiGate device, you want to minimize the impact in your OT network.
Therefore, you deploy it initially as an offline IDS. Which two statements about this deployment are correct?
(Choose two answers)
Answer: A,B
Explanation:
Deploying a FortiGate in offline IDS (also known as one-arm sniffer mode) is a common strategy in OT environments for several reasons found in the study guide:
* Priority of Availability : In OT, availability and safety are critically important and prioritized higher than in IT. An offline IDS minimizes impact because it does not sit in the direct path of production traffic.
* Network Sensor Role : In this mode, the FortiGate is connected to a mirror/SPAN port on a switch. It acts as a network sensor , receiving a copy of the traffic rather than having the traffic flow through it.
This confirms Statement A is correct and Statement D is incorrect.
* Passive vs. Active : The guide explicitly states that in OT environments, passive methods are preferred over active methods to avoid negatively impacting performance or causing process interruptions.
* Depth of Visibility : Even though the device is offline, you apply security profiles (such as IPS, Application Control, and Antivirus) to the sniffer interface. This allows the FortiGate to analyze the copied traffic and provide deep visibility into the OT assets and their behaviors. This confirms Statement B is correct.
* Detection vs. Prevention : An IDS (Intrusion Detection System) is passive ; it can detect threats but cannot reset connections or drop packets to block attacks. Therefore, it cannot block zero-day attacks, making Statement C incorrect.
NEW QUESTION # 43
Refer to the exhibit. From your analysis of the output, which statement about the output is true?
Answer: C
Explanation:
ph_dev_mon is a PAM event. Hostname is WIN2K8DC (a win server) not Fortigate.
NEW QUESTION # 44
Refer to the exhibits.
A partial Incident Analysis page and the log details related to the event are shown. An attack is reported on your OT network. You analyze the corresponding incident. Based on the information provided on the Incident Analysis page and the log details, which two statements are correct? (Choose two answers)
Answer: D,E
Explanation:
Based on the technical data provided in the exhibits and the OT Security 7.6 Architect curriculum:
* Industrial Protocol Identification (Statement A) : The log details exhibit clearly shows that the Destination Port used in the attack is 502 . According to the study guide ' s section on Industrial Protocol Protection , the standard port used by the Modbus TCP protocol is 502 . Furthermore, the attack name identifies a " Triangle.Research.Nano-10.PLC, " which are industrial controllers commonly utilizing Modbus for communications.
* Attack Mitigation (Statement B) : The log details specify that the Action taken by the FortiGate (Edge-FortiGate) was dropped . In cybersecurity and Fortinet fabric operations, dropping a packet associated with an IPS signature means the traffic was blocked from reaching its target, thereby mitigating the attack.
* Target IP Address (Statement E) : The log detail explicitly lists the Destination IP as 192.168.2.3 .
The Incident Analysis page also titles the incident with dstip:192.168.2.3. While the " Affected Endpoint " is shown as 10.1.5.20 , in an " outgoing " attack direction (as shown in the log), this likely refers to the internal source/attacker IP, whereas the target is the destination IP (192.168.2.3). Thus, Statement E is incorrect.
* Protocol Conflict (Statement C) : The IEC 104 protocol typically utilizes port 2404 . Since the log specifies port 502, Statement C is incorrect.
* Severity Distinction (Statement D) : While the Incident severity is marked as High , the question specifically asks about event severity. The " Events " table at the bottom of the Incident Analysis page shows a " User login/logout failed " event with a medium severity. Because there is a distinction in the management console between the severity of individual events and the aggregated incident, and Statement A and B are technically definitive based on port and action, A and B are the correct architectural choices.
NEW QUESTION # 45
Refer to the exhibit. A Run_report task is shown.
You want to automate the generation of a newly created report on FortiAnalyzer.
When you configure the Run_report task in Playbook, why is the report not shown in the Report field? (Choose two answers)
Answer: D,E
NEW QUESTION # 46
The operational technology (OT) network analyst runs different levels of reports to investigate threats that exploit the network. The analyst can run these reports on all routers, switches, and firewalls.
Which FortiSIEM reporting method can analysts use to identify threats that exploit image firmware files?
Answer: C
Explanation:
Threat hunting reports let analysts query events and indicators (like anomalous firmware image access/use) across routers, switches, and firewalls, revealing exploits targeting firmware files.
NEW QUESTION # 47
......
Our company is widely acclaimed in the industry, and our NSE6_OTS_AR-7.6 study materials have won the favor of many customers by virtue of their high quality. Started when the user needs to pass the qualification test, choose the NSE6_OTS_AR-7.6 study materials, they will not have any second or even third backup options, because they will be the first choice of our practice exam materials. Our NSE6_OTS_AR-7.6 Study Materials are devoted to research on which methods are used to enable users to pass the test faster.
Prep NSE6_OTS_AR-7.6 Guide: https://www.real4dumps.com/NSE6_OTS_AR-7.6_examcollection.html
BTW, DOWNLOAD part of Real4dumps NSE6_OTS_AR-7.6 dumps from Cloud Storage: https://drive.google.com/open?id=1aNSR4GvBPb0YBDbqpmBxEmK6QkPSaLqx