You don't have to worry about passing rates of our NSE6_FNC_AD-7.6 exam questions because of the short learning time. We have always been trying to shorten your study time on the premise of ensuring the passing rate. Perhaps after you have used NSE6_FNC_AD-7.6 real exam once, you will agree with this point. Our NSE6_FNC_AD-7.6 Study Materials are really a time-saving and high-quality product! As long as you buy and try our NSE6_FNC_AD-7.6 practice braindumps, then you will want to buy more exam materials.
| Section | Objectives |
|---|---|
| Network Visibility and Monitoring | - Guests and contractors - Explain and configure device profiling - Troubleshoot network devices and device status - Use logging options available on FortiNAC |
| Concepts and Initial Configuration | - Model and organize infrastructure devices - Explain isolation networks and the configuration wizard |
| Deployment and Provisioning | - Configure security automation - Configure access control on FortiNAC-F - Configure and monitor high availability (HA) - Configure FortiNAC-F security policies |
| Integration | - Configure and use FortiNAC-F Manager - Explain and configure MDM integration - Integrate with third-party devices using Syslog and SNMP trap input |
>> New NSE6_FNC_AD-7.6 Exam Bootcamp <<
If you must complete your goals in the shortest possible time, our NSE6_FNC_AD-7.6 exam materials can give you a lot of help. For our NSE6_FNC_AD-7.6 study guide can help you pass you exam after you study with them for 20 to 30 hours. And our products are global, and you can purchase our NSE6_FNC_AD-7.6 training guide is wherever you are. Believe us, our products will not disappoint you. Our global users can prove our strength.
NEW QUESTION # 25
Refer to the exhibits.
An administrator is troubleshooting visibility issues on a modeled switch The switch is configured to use link traps and to provision hosts based on network access policies. The administrator is seeing hosts on ports with no hosts connected and not seeing hosts on ports where hosts are known to be connected.
What is the most likely cause?
Answer: C
Explanation:
The correct answer is C . In a link-trap-based wired deployment, the switch sends a linkUp or linkDown SNMP trap to FortiNAC-F, but that trap does not contain the endpoint MAC address. After receiving the link trap, FortiNAC-F must contact the switch and perform a Layer 2 poll to read the forwarding table and determine which MAC address was added or removed on the port. The FortiNAC-F study guide states that link traps trigger FortiNAC-F to perform a Layer 2 poll to update its awareness of devices connected to the edge device, and the wired link-trap workflow specifically shows FortiNAC-F performing a Layer 2 poll before locating the host record and provisioning access.
The symptoms in the exhibit are classic stale Layer 2 visibility: FortiNAC-F still shows a rogue host on a port where no host is connected, while also failing to show hosts on ports where endpoints are actually connected.
That means FortiNAC-F is not successfully refreshing the switch MAC table information. Since link traps depend on FortiNAC-F being able to poll the switch after the trap, a contact failure with the modeled switch is the most likely cause.
Option A is wrong because logical network settings affect access enforcement, not whether FortiNAC-F can see current MAC-to-port mappings. Option B is wrong because the FortiNAC-F agent is not required for basic switch-port visibility; Layer 2 visibility comes from switch polling, MAC notification traps, or RADIUS. Option D is tempting, but the broader failure shown here is not merely a policy or endpoint-side issue-it is that FortiNAC-F cannot obtain current Layer 2 data from the switch. In practice, you would still verify SNMP/CLI credentials while troubleshooting, but the best answer to the symptom pattern is that FortiNAC-F cannot contact/query the switch successfully.
NEW QUESTION # 26
When FortiNAC-F is managing VPN clients connecting through FortiGate, why must the clients run a FortiNAC-F agent?
Answer: C
Explanation:
When FortiNAC-F manages VPN clients through a FortiGate, the agent plays a fundamental role in device identification that standard network protocols cannot provide on their own. In a standard VPN connection, the FortiGate establishes a Layer 3 tunnel and assigns a virtual IP address to the client. While the FortiGate sends a syslog message to FortiNAC-F containing the username and this assigned IP address, it typically does not provide the hardware (MAC) address of the remote endpoint's physical or virtual adapter.
FortiNAC-F relies on the MAC address as the primary unique identifier for all host records in its database. Without the MAC address, FortiNAC-F cannot correlate the incoming VPN session with an existing host record to apply specific policies or track the device's history. By running either a Persistent or Dissolvable Agent, the endpoint retrieves its own MAC address and communicates it directly to the FortiNAC-F service interface. This allows the "IP to MAC" mapping to occur.
Once FortiNAC-F has both the IP and the MAC, it can successfully identify the device, verify its status, and send the appropriate FSSO tags or group information back to the FortiGate to lift network restrictions.
NEW QUESTION # 27
Which two things must be done to allow FortiNAC to process incoming syslog messages from an unknown vendor? (Choose two.)
Answer: C,D
NEW QUESTION # 28
When configuring FortiNAC-F to manage FortiGate VPN users, an endpoint compliance policy must be created for the integration.
Why is the endpoint compliance policy necessary for this type of integration?
Answer: B
Explanation:
The integration of FortiNAC-F with FortiGate VPN requires a specific policy workflow to bridge the gap between initial user authentication and full network access. When a user connects to the VPN, the FortiGate typically provides the User ID and IP address, but FortiNAC-F requires a MAC address to uniquely identify and manage the endpoint's record.
According to the FortiGate VPN Integration Guide, the Endpoint Compliance Policy is a mandatory component of this setup because it is used to designate the required agent type.
Because a VPN connection is Layer 3, FortiNAC cannot "see" the MAC address through traditional SNMP or L2 polling. The compliance policy instructs the system to present a Captive Portal to the remote user, requiring them to download and run either the Persistent or Dissolvable Agent. The agent then reports the device's MAC address back to FortiNAC, allowing the system to correlate the VPN session with a host record.
Once the agent is running and the MAC is known, FortiNAC-F can evaluate the device's security posture (if scanning is configured) and send the necessary FSSO tags back to the FortiGate to lift the initial network restrictions. Without the compliance policy to enforce the agent requirement, the connection would remain in an isolated "IP-only" state with no unique hardware identity.
"The Endpoint Compliance Policy is necessary to control the agent requirement for VPN users.
Create a default VPN Endpoint Compliance Policy to distribute an agent via captive portal for isolated machines. This policy allows the administrator to designate the required agent type (Persistent or Dissolvable) that will be used to collect the hardware (MAC) address and perform health scans on the remote endpoint."
NEW QUESTION # 29
Refer to the exhibit.
Given this topology, and a layer 3 registration network configuration, which IP address would be designated in the DHCP relay configuration for the registration network?
Answer: C
Explanation:
The correct answer is D . In a Layer 3 registration or isolation network design, DHCP requests from the isolated registration VLAN are not served locally on that VLAN by a normal production DHCP server.
Instead, the registration VLAN's DHCP relay must forward DHCP traffic to FortiNAC-F port2 , because port2 is the captive network service interface. The study guide states that in Layer 3 captive networks, DHCP traffic is relayed to port2 from the captive networks, and that the FortiNAC-F port2 interface provides DHCP, DNS, and captive portal services for hosts assigned to those captive networks.
In the exhibit, the registration VLAN is 192.168.10.x/24 , with gateway 192.168.10.254 . That gateway is where the DHCP relay would be configured, but it is not the relay destination. The relay destination must be the FortiNAC-F port2 address, shown as 192.168.200.10 . The corporate DHCP server 192.168.100.75 is for production network addressing, not registration isolation. The FortiNAC-F port1 address 192.168.100.20 is the administrative or production-facing interface, not the captive network service interface. Therefore, the DHCP relay should point to 192.168.200.10 .
NEW QUESTION # 30
......
With the intense competition in labor market, it has become a trend that a lot of people, including many students, workers and so on, are trying their best to get a NSE6_FNC_AD-7.6 certification in a short time. The NSE6_FNC_AD-7.6 exam prep is produced by our expert, is very useful to help customers pass their exams and get the certificates in a short time. We are going to show our NSE6_FNC_AD-7.6 Guide braindumps to you. We can sure that our product will help you get the certificate easily. If you are wailing to believe us and try to learn our NSE6_FNC_AD-7.6 exam torrent, you will get an unexpected result.
NSE6_FNC_AD-7.6 Exam Tips: https://www.itexamdownload.com/NSE6_FNC_AD-7.6-valid-questions.html