M2無料過去問 & M2トレーニング資料

M2試験は優秀なあなたにとって難しくないかもしれませんが、試験の合格を保証するために、参照できる資料を購入することができます。我々のM2問題集は通過率が高いので、あなたの要求を満たすことができます。資料を購入するなら、弊社のM2問題集を選んでください。

International Code Council M2 Exam Syllabus Topics:

SectionObjectives
General Administration and Mechanical Inspection Practice- Code enforcement procedures and inspector responsibilities
  • 1. Permit requirements and inspections
    • 2. Documentation and reporting
      Mechanical Appliances and Equipment- Boilers, furnaces, and water heaters
      • 1. Installation and inspection requirements
        • 2. Safety controls and venting
          Ventilation and Indoor Air Quality- Ventilation requirements
          • 1. Exhaust systems
            • 2. Outdoor air intake requirements
              Mechanical Code (IMC) Fundamentals- International Mechanical Code application
              • 1. Scope and definitions
                • 2. General regulations
                  HVAC Systems and Equipment- Heating and cooling systems
                  • 1. Duct systems design and installation
                    • 2. Air handling units and system components
                      Fuel Gas Systems- Gas piping and appliance installation
                      • 1. Combustion air requirements
                        • 2. Gas safety and testing

                          >> M2無料過去問 <<

                          便利なM2無料過去問 & 合格スムーズM2トレーニング資料 | 実際的なM2模擬対策 Commercial Mechanical Inspector

                          あなたは今やはりM2試験に悩まされていますか？長い時間M2試験を取り組んいる弊社はあなたにM2練習問題を提供できます。あなたはM2試験に興味を持たれば、今から行動し、M2練習問題を買いましょう。M2試験に合格するために、M2練習問題をよく勉強すれば、いい成績を取ることが難しいことではありません。つまりM2練習問題はあなたの最も正しい選択です。

                          International Code Council Commercial Mechanical Inspector 認定 M2 試験問題 (Q45-Q50):

                          質問 # 45
                          The optional integral clearance reduction system is designed to meet which NFPA standard?

                          正解：D

                          解説：
                          Based on the specification sheet shown in the exhibit, the design features state that the optional integral clearance reduction system meets the requirements of NFPA 96 . Therefore, the correct answer is D .


                          質問 # 46
                          The minimum size for access openings for fire dampers shall be:

                          正解：A

                          解説：
                          The IMC requires access openings for fire dampers to be of a size that allows maintenance and resetting of the damper . The code does not set the answer as same-as-duct, half-diagonal, or a universal 12-inch by 12- inch opening. So Option C is correct.


                          質問 # 47
                          When a furnace is installed in a 66-inch-high attic, the maximum distance from the passageway access to the furnace shall be _____ ft., measured along the centerline of the passageway.

                          正解：D

                          解説：
                          ICC mechanical access provisions for appliances in attics require the passageway to be not more than 20 feet in length , measured along the centerline of the passageway from the opening to the appliance, where the attic passageway is the standard reduced-height access condition. Since the attic height given is 66 inches, the standard maximum length applies, so Option C is correct. The 50-foot allowance applies only under a different exception where the passageway is unobstructed and at least 6 feet high for its entire length.


                          質問 # 48
                          Given: A recirculating industrial direct-fired makeup air heater has a rated input of 200,000 Btu/h .
                          Ventilation air is supplied by separate mechanical means.
                          Outside ventilation air shall be provided to supply at least _____ CFM.

                          正解：C

                          解説：
                          The applicable provision requires direct-fired industrial air heaters to supply outside ventilation air at a rate of not less than 4 cfm per 1,000 Btu/h of rated input where ventilation air is provided by separate mechanical means. For 200,000 Btu/h , the required outside air is:
                          200,000 ÷ 1,000 = 200
                          200 × 4 = 800 cfm
                          So the correct answer is C


                          質問 # 49
                          Indoor combustion air shall be provided within:

                          正解：A

                          解説：
                          For indoor combustion air openings, one opening must commence within 12 inches of the top of the enclosure and one within 12 inches of the bottom . That corresponds to 1 foot of the ceiling and 1 foot of the floor , so Option A is correct.


                          質問 # 50
                          ......

                          Pass4Testはこの分野のリーダーであり、M2学習ガイドの高い合格率で有名です。認定試験に頭痛の種がある場合は、M2学習ガイドの資料が優れた救世主になります。 100％合格率の最も有効でプロフェッショナルなM2学習ガイド資料を提供するのは今がチャンスです。一度試験をクリアして成功を収めたい場合は、私たちを選ぶことが賢明です。あなたが私たちについてするならば、私たちの満足のいくサービスと高品質のM2ガイド急流について以下に注意を払ってください。

                          M2トレーニング資料: https://www.pass4test.jp/M2.html