For your information, the passing rate of our SRAN-Radio-Network-Performance-Optimization study questions is over 98% up to now. Up to now our SRAN-Radio-Network-Performance-Optimization practice materials consist of three versions, all those three basic types are favorites for supporters according to their preference and inclinations. On your way moving towards success, our SRAN-Radio-Network-Performance-Optimization Preparation materials will always serves great support. And you can contact us at any time since we are serving online 24/7.
| Section | Weight | Objectives |
|---|---|---|
| Coverage and Capacity Optimization | 30% | - Coverage analysis, tuning and optimization - Capacity planning, load balancing and optimization - Interference analysis and mitigation techniques |
| Mobility and Handover Optimization | 20% | - Inter-RAT mobility and optimization - Mobility robustness and optimization - Handover parameters and algorithms |
| SRAN Performance Optimization Fundamentals | 25% | - Performance optimization principles and methodology - Key performance indicators (KPIs) definition and measurement - Network performance monitoring and analysis tools |
| Advanced Optimization and SON Features | 10% | - Self-Organizing Networks (SON) use cases and optimization - Energy saving and advanced features |
| Quality of Service and Resource Management | 15% | - QoS parameters, scheduling and admission control - Radio resource management and optimization |
>> SRAN-Radio-Network-Performance-Optimization Exam Dumps Free <<
ITExamSimulator has made the Nokia SRAN-Radio-Network-Performance-Optimization exam dumps after consulting with professionals and getting positive feedback from customers. The team of ITExamSimulator has worked hard in making this product a successful SRAN-Radio-Network-Performance-Optimization study material. So we guarantee that you will not face issues anymore in passing the SRAN-Radio-Network-Performance-Optimization Certification test with good grades. ITExamSimulator has built customizable SRAN-Radio-Network-Performance-Optimization practice exams (desktop software & web-based) for our customers.
NEW QUESTION # 16
What is the role of admission control in 5G networks ?
Answer: A
Explanation:
The correct answer is D .
Admission control is responsible for deciding whether a new UE connection, bearer, service, or session can be accepted by the cell without negatively affecting existing users and services.
In 5G RAN, admission control checks available radio resources such as:
* PRB availability
* PDCCH/PUCCH capacity
* UE context capacity
* QoS requirements
* GBR or non-GBR bearer requirements
* Cell load and congestion status
It does not directly manage modulation schemes; that is handled by link adaptation. It also does not directly increase spectral efficiency or optimize downlink throughput, although good admission control indirectly protects user experience and avoids overload.
So the main role of admission control is:
To check whether there are enough resources for new connections.
NEW QUESTION # 17
What is the mandatory prerequisite to implement DSS , or Dynamic Spectrum Sharing ?
Answer: C
Explanation:
The correct answer is D .
DSS allows LTE and 5G NR to share the same spectrum dynamically , instead of requiring a separate dedicated NR carrier. Therefore, dedicated NR spectrum is not mandatory. DSS is also not limited to TDD only; it is commonly used in FDD spectrum refarming scenarios as well. Public RAN references describe DSS as a mechanism where LTE and NR coexist in the same frequency band and share spectrum dynamically.
From an SRAN architecture point of view, the mandatory deployment condition is that the radio platform must support LTE and NR coexistence on the same radio resources. That requires RF module sharing or a DSS-capable shared radio configuration.
So the correct prerequisite is:
RF module sharing.
NEW QUESTION # 18
At which mark are all conditions fulfilled for energy saving , so the cell will be switched off? Refer to the image below.
Answer: B
Explanation:
The correct answer is B , which corresponds to mark C in the diagram.
In the diagram, the energy-saving process follows these stages:
Before mark B , the cell is entering the power-saving period, but the required load condition has not yet been satisfied for the required duration.
At mark B , the measured load has gone below the configured threshold, but the cell is not switched off immediately. The system must confirm that the load remains below the required threshold for the configured time.
At mark C , the load has stayed below the required threshold for the required duration, shown as 5 minutes in the diagram. At this point, all conditions are fulfilled, and the cell can be switched off. The diagram also shows the state becoming:
energySavingState = energySaving
Marks D and E are already inside or near the later part of the power-saving period. Mark E is associated with operator suspension/exit behavior, not the initial moment when all switch-off conditions are first fulfilled.
NEW QUESTION # 19
A slice supporting sensors and smart meters would be categorized as:
Answer: A
Explanation:
The correct answer is A .
Sensors and smart meters are typical massive IoT use cases. They usually involve a very large number of devices sending small amounts of data, often with low mobility and low power requirements.
This type of traffic fits mMTC , or massive Machine Type Communications .
Why the other options are not correct:
URLLC is used for very low-latency and highly reliable services, such as industrial automation, remote control, or mission-critical applications.
eMBB is used for high-throughput broadband services, such as video, fixed wireless access, or enhanced mobile internet.
DNN is not a slice category. It means Data Network Name and identifies the data network the UE connects to, similar to APN in LTE.
Therefore, a slice supporting sensors and smart meters is categorized as:
mMTC.
NEW QUESTION # 20
In a 5G NSA Option 3x deployment, why should we not define 5G neighbors in LTE sectors where there is no 5G coverage ?
Answer: B
Explanation:
The correct answer is A .
In 5G NSA Option 3x , LTE acts as the Master Cell Group , and NR acts as the Secondary Cell Group , usually added through EN-DC . If 5G NR neighbors are configured in an LTE sector where there is actually no 5G coverage , the LTE eNB may still configure the UE to perform NR measurements.
To perform NR inter-RAT or inter-frequency measurements, the UE may require measurement gaps .
During these gaps, the UE stops normal LTE reception/transmission activities to measure NR frequencies. If there is no real 5G coverage, those gaps become wasted measurement time and can reduce LTE user throughput.
Option B is not the best answer because if there is no 5G coverage, the main issue is not successful SCG addition or handover degradation, but unnecessary measurement activity. Option C is also not correct because redirection from 5G to 4G normally occurs when the UE is already on or connected to 5G coverage, which is not the case here.
Therefore, the main reason is:
LTE throughput degradation due to unnecessary measurement gap configuration.
NEW QUESTION # 21
......
We know how expensive it is to take SRAN-Radio-Network-Performance-Optimization exam. It costs both time and money. However, with the most reliable exam dumps material from ITExamSimulator, we guarantee that you will pass the SRAN-Radio-Network-Performance-Optimization exam on your first try! You’ve heard it right. We are so confident about our SRAN-Radio-Network-Performance-Optimization Exam Dumps for Nokia SRAN-Radio-Network-Performance-Optimization exam that we are offering a money back guarantee, if you fail. Yes you read it right, if our SRAN-Radio-Network-Performance-Optimization exam braindumps didn’t help you pass, we will issue a refund - no other questions asked.
SRAN-Radio-Network-Performance-Optimization Online Version: https://www.itexamsimulator.com/SRAN-Radio-Network-Performance-Optimization-brain-dumps.html