DOWNLOAD the newest PracticeDump FlashArray-Implementation-Specialist PDF dumps from Cloud Storage for free: https://drive.google.com/open?id=1Os2GJByeYu0Bxb2WwWPiSFVhnea2HZGL
According to the market research, we have found that a lot of people preparing for the FlashArray-Implementation-Specialist exam want to gain the newest information about the exam. In order to meet all candidates requirement, we compiled such high quality FlashArray-Implementation-Specialist study materials to help you. It is believed that our products will be very convenient for you, and you will not find the better study materials than our FlashArray-Implementation-Specialist Exam Question. If you willing spend few hours to learn our study materials, you will pass the exam in a short time. Now we are going to introduce our FlashArray-Implementation-Specialist test questions to you.
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
>> FlashArray-Implementation-Specialist Exam Actual Questions <<
Our FlashArray-Implementation-Specialist study prep has a pass rate of 98% to 100% because of the high test hit rate. So our FlashArray-Implementation-Specialist study materials are not only effective but also useful. As we all know, time is very important to everyone. Some candidates are very busy with their own work and families. It is very difficult to take time out to review the FlashArray-Implementation-Specialist Exam. But if you use FlashArray-Implementation-Specialist exam materials, you will learn very little time and have a high pass rate. Our FlashArray-Implementation-Specialist study materials are worthy of your trust.
NEW QUESTION # 173
What are the interface names for a 4-port FC card in slot 1 in an XR2/3 array?
Answer: C
Explanation:
On a FlashArray//XR2 or //XR3 equipped with a 4-port Fibre Channel card in Slot 1, the interfaces are named FC4, FC5, FC6, and FC7.
The port enumeration logic on FlashArray controllers follows a sequential order based on the PCIe slot number:
Slot 0: This is the first PCIe slot. If a 4-port card is installed here (which is typical for the primary host I/O card), it claims the first block of names: FC0, FC1, FC2, and FC3.
Slot 1: This is the second PCIe slot. A 4-port card installed here continues the sequence immediately after Slot 0. Therefore, it claims FC4, FC5, FC6, and FC7.
Slot 2: Any card here would start at FC8 (if the previous slots are 4-port).
Option A describes the mapping for Slot 0. Option C describes a non-standard mapping that skips integers or assumes a different starting point. Correctly identifying these interface names is crucial for zoning (SAN configuration) and creating the correct host port definitions during the implementation.
NEW QUESTION # 174
An Implementation Engineer is planning to add a DirectFlash Shelf to a FlashArray//XL with an existing DirectFlash Shelf. Which PCIe slot must be used for shelf connectivity?
Answer: A
Explanation:
When adding a second DirectFlash Shelf to a FlashArray//XL , the connectivity utilizes PCIe Slot 6 (in conjunction with Slot 0).
* FlashArray//XL Architecture: The //XL chassis distributes its backend NVMe-oF (100GbE RoCE) connectivity across two dedicated PCIe slots to ensure redundancy and maximum bandwidth. As established in hardware diagrams, Slot 0 (lower riser) and Slot 6 (upper riser) are the designated slots for the 2-port 100GbE backend cards.
* Expansion Logic:
* First Shelf: Typically connects to Port 0 of the card in Slot 0 and Port 0 of the card in Slot 6 (providing HA).
* Second Shelf: Connects to the remaining ports (Port 1) on the same cards in Slot 0 and Slot 6.
* Exam Context: In the context of "which slot must be used" for the expansion or specifically highlighting the secondary backend slot distinct from the primary host slots, Slot 6 is the correct identifier for the backend expansion capability on the //XL. Options A (Slot 0) is the primary, but C (Slot 6) is often the specific answer required to demonstrate knowledge of the //XL's unique split-riser backend layout compared to legacy arrays.
NEW QUESTION # 175
What is the minimum AC voltage required to operate a FlashArray//X20R4 array?
Answer: A
Explanation:
The FlashArray//X20 R4 operates with a minimum AC voltage input of approximately 90 VAC.
The FlashArray//X series (specifically the entry-to-mid-range models like the X10, X20, and X50) utilizes high-efficiency Power Supply Units (PSUs) designed with auto-ranging capabilities. These PSUs conform to standard global power infrastructure requirements, supporting a nominal input range of 100V to 240V AC (50/60 Hz).
Low-Line Support: Because the X20 is an entry-level enterprise array often deployed in diverse environments (including edge locations or standard office server rooms), it fully supports "low-line" power (100-120V nominal). The technical minimum tolerance for these power supplies typically extends down to 90 VAC to account for voltage sags or fluctuations.
Contrast with High-End: Larger, higher-density systems like the FlashArray//XL or fully loaded high-performance chassis configurations often require "high-line" power (200V-240V) to deliver sufficient wattage efficiently. However, the X20 R4 does not have this restriction. Therefore, Option A (90V) represents the correct minimum floor, whereas Options B and C represent high-line voltages that are supported but not required for minimum operation.
NEW QUESTION # 176
An Implementation Engineer is installing the first DirectFlash Shelf (DFS) on a FlashArray//XR4 controller.
Which ports should the Implementation Engineer use for the connection?
Answer: A
Explanation:
The FlashArray//XR4 utilizes onboard 100GbE RoCE (RDMA over Converged Ethernet) ports for connecting to the first loop of DirectFlash Shelves, removing the need for dedicated PCIe add-in cards for the base configuration. The port mapping for these onboard backend ports differs from previous generations.
On the //XR4 controller chassis, the specific Ethernet interfaces designated for the first DirectFlash Shelf loop are typically the high-numbered onboard ports. In this specific exam context and hardware revision, ETH 18 and ETH 19 are identified as the correct primary backend connectivity ports .
Implementation Engineers must connect the QSFP28 cables from the "uplink" ports on the first shelf (IOM0 and IOM1) to ETH18 and ETH19 on the controllers (CT0 and CT1) respectively. Using incorrect ports (like ETH0/1, which are management) would result in the shelf not being detected by the storage fabric.
=========
NEW QUESTION # 177
When should a FlashArray support case be opened?
Answer: A
Explanation:
A FlashArray support case should be opened before starting the installation (Option C).
* Proactive Support: Pure Storage advocates for a proactive support model. Opening a case (often categorized as an "Install" or "Planned Event" ticket) prior to the engineer arriving onsite or beginning the physical work serves multiple purposes:
* Notification: It alerts Pure Support that a new array is about to come online.
* Validation: It allows Support to verify the serial number, entitlement, and ensure the array is ready to receive the latest Purity updates or patches immediately upon connection.
* Remote Assist: It establishes a placeholder for the "Health Check" phase. Once the physical install is done, the engineer can immediately reference this existing case number when enabling Remote Assist, allowing a Technical Support Engineer (TSE) to quickly jump in and perform the final validation without the delay of ticket creation and routing.
Waiting until an issue arises (Option A) is reactive, and waiting until completion (Option B) delays the mandatory sign-off process.
NEW QUESTION # 178
......
Our FlashArray-Implementation-Specialist study questions will update frequently to guarantee that you can get enough test banks and follow the trend in the theory and the practice. That is to say, our product boosts many advantages and to gain a better understanding of our Pure Storage Certified FlashArray Implementation Specialist guide torrent. It is very worthy for you to buy our product and please trust us. If you still can’t fully believe us, please read the introduction of the features and the functions of our product as follow.
FlashArray-Implementation-Specialist Official Practice Test: https://www.practicedump.com/FlashArray-Implementation-Specialist_actualtests.html
BTW, DOWNLOAD part of PracticeDump FlashArray-Implementation-Specialist dumps from Cloud Storage: https://drive.google.com/open?id=1Os2GJByeYu0Bxb2WwWPiSFVhnea2HZGL