ValidExam is professional platform to establish for compiling 300-110 exam materials for candidates, and we aim to help you to pass the 300-110 examination as well as getting the related certification in a more efficient and easier way. Owing to the superior quality and reasonable price of our 300-110 Exam Materials, our 300-110 exam torrents are not only superior in price than other makers in the international field, but also are distinctly superior in many respects. Our pass rate of 300-110 exam braindump is as high as 99% to 100%, which is unique in the market.
| Section | Weight | Objectives |
|---|---|---|
| WLAN High Availability and Security Design | 20% | - High availability design
- Security architecture design
|
| Wireless Site Survey | 25% | - Layer 1 site survey execution and analysis - RF propagation and attenuation analysis - Pre-deployment survey and validation - Design requirements collection and constraint evaluation
|
| Mobility Design | 25% | - Roaming optimization
- Mobility architecture models
|
| Wireless Infrastructure Design | 30% | - Wired-wireless integration design
|
>> Cisco 300-110 Study Test <<
If you prepare 300-110 real exam with our training materials, we guarantee your success in the first attempt. Our test engine enables you practice 300-110 exam questions in the mode of the formal test and enjoy the atmosphere of the actual test. Our 300-110 Practice Test is a way of exam simulation that will mark your mistakes and remind you when you practice dump next time.
NEW QUESTION # 32
How are mobility groups created, excluding mobility anchors?
Answer: A
Explanation:
Mobility groups are created by configuring each Wireless LAN Controller (WLC) to use the same mobility domain name (mobility group name) and defining each WLC as a peer in the static mobility members list of every other WLC in the group. This bidirectional configuration establishes the trusted peer relationship and enables WLCs to exchange client information, security credentials, and state data for seamless roaming. The same mobility group name on all WLCs creates a shared identity; the static peer list defines which controllers are trusted mobility partners and provides their management IP addresses and MAC addresses for tunnel establishment. Option A is incorrect because members should run compatible (ideally the same) software versions, not different ones. Option B is incorrect - all WLCs in a mobility group must use the same virtual IP address for proper roaming. Option D is incorrect - in an HA SSO pair, the pair presents as a single logical mobility entity, not as two separate peers. Reference: WLSD Study Guide - Mobility Group Configuration, Peer Configuration Requirements, Mobility Domain Architecture.
NEW QUESTION # 33
An engineer is designing a wireless network for a small airport and completes the initial walkthrough phase of the facility. Which step of the WLAN site survey should the engineer perform next?
Answer: B
Explanation:
The Cisco WLAN site survey methodology follows a structured, sequential process. The initial walkthrough -- sometimes called the discovery or orientation phase -- is the first step, during which the engineer physically tours the facility to understand its physical characteristics: building materials, structural layout, potential AP mounting locations, wiring closet positions, and environmental factors. After completing the initial walkthrough, the next logical phase is the predeployment survey (also referred to as a pre-deployment or predictive survey). The predeployment survey uses the information gathered during the walkthrough to create a detailed design plan -- either through a manual AP placement plan or a predictive survey tool such as Ekahau, where floor plans are annotated with materials and attenuation values and APs are virtually placed to model coverage. The predeployment survey output is the design document that drives the actual physical installation.
NEW QUESTION # 34
A customer wants to provide wireless coverage in a parking lot outside of a building. An engineer determines that three APs are required. The APs can be mounted on the light poles in the parking lot because there are cable routes already in place for these locations. The closest wiring closet is approximately 200 meters away. Which setup powers and connects the APs back to the customer network?
Answer: B
Explanation:
This question hinges on a fundamental network engineering constraint: the maximum transmission distance of copper Ethernet cabling. IEEE 802.3 standards specify a maximum segment length of 100 meters for all standard PoE and Ethernet over Category 5e, 6, or 6A UTP copper cabling. The parking lot light poles are approximately 200 meters from the closest wiring closet -- more than double the maximum copper distance. This immediately eliminates Options A and D (Category 6 UTP): at 200 meters, UTP copper cannot reliably carry Ethernet at any supported speed. The correct solution is fiber optic connectivity between the wiring closet and the parking lot poles, combined with a local AC/DC power module at each pole location. Fiber optic cabling supports runs of hundreds of meters to kilometers -- easily spanning 200 meters. At the AP mounting location on the light pole, an AC/DC power module (powered from the pole's existing electrical supply) converts AC power to the DC power the AP requires. Option B (fiber with 802.3af) is incorrect because PoE cannot be delivered over fiber -- 802.3af requires copper cabling for simultaneous power and data delivery. The AC/DC power module at the remote end is the correct power solution when fiber is required.
NEW QUESTION # 35
A wireless engineer is designing a wireless network for a warehouse using access points with internal antennas. Which two elements have a negative effect on the wireless users? (Choose two.)
Answer: A,C
Explanation:
In a warehouse setting, two elements with a significant negative effect on wireless performance are AP height and absorption. AP height (Option B) is critical because warehouses often have very high ceilings (25-45 feet). When APs with internal (omnidirectional) antennas are mounted too high, the signal propagates primarily in the horizontal plane and the path loss to floor-level worker devices becomes excessive.
Additionally, metal shelving between the AP and users further attenuates the already weak signal at high mounting heights. Absorption (Option E) is a major challenge in warehouses because the inventory stored on metal racks, particularly liquid goods, dry goods in cardboard, and dense materials, absorbs RF energy significantly. Metal racking causes both absorption and reflection, creating RF shadows and multipath environments that degrade connection quality. Wireless channels (Option A) are a design parameter, not an environmental impediment. Client authentication (Option C) and authorization (Option D) are network security processes unrelated to RF propagation quality. Reference: WLSD Study Guide - Warehouse Wireless Design, AP Height Considerations, RF Absorption in Industrial Environments.
NEW QUESTION # 36
A conference center is designing a Wi-Fi 6 deployment for a room holding 2000 attendees, most of whom will use low-bandwidth applications. Which Wi-Fi 6 capability most directly improves efficiency in this scenario?
Answer: B
Explanation:
The defining problem in a high-density room with many low-bandwidth clients is not raw per-client throughput but the overhead of medium contention - under 802.11ac, each small packet requires a full channel access cycle, so the channel spends most of its airtime on contention and preamble rather than payload. OFDMA divides the channel into resource units so the AP can serve multiple clients within a single transmit opportunity, dramatically reducing per-frame overhead when the traffic mix is many small transmissions. This is precisely the profile of a conference audience running chat, email, and browsing. 1024-QAM raises peak modulation but only benefits clients already at very high signal levels and does nothing for contention. 160 MHz channel bonding is counterproductive in high density because it collapses the number of reusable channels. Target Wake Time improves client battery life by scheduling wake intervals, which is valuable for IoT but does not address the airtime efficiency problem in this design.
NEW QUESTION # 37
......
There are many other advantages. To gain a full understanding of our product please firstly look at the introduction of the features and the functions of our 300-110 exam torrent. The page of our product provide the demo and the aim to provide the demo is to let the you understand part of our titles before their purchase and see what form the software is after the you open it. The client can visit the page of our product on the website. So the client can understand our 300-110 Quiz torrent well and decide whether to buy our product or not at their wishes. The client can see the forms of the answers and the titles.
300-110 Accurate Study Material: https://www.validexam.com/300-110-latest-dumps.html