DOWNLOAD the newest LatestCram 350-101 PDF dumps from Cloud Storage for free: https://drive.google.com/open?id=14vcQrd5vM3hAnhr-lFN8pwXmv5BjVDBa
Choose the right format of Cisco 350-101 actual questions and start 350-101 preparation today. Top Notch Cisco 350-101 Actual Dumps Are Ready for Download. Now is the ideal time to prepare for and crack the Cisco 350-101 Exam. To do this, you just need to enroll in the 350-101 examination and start preparation with top-notch and updated Cisco 350-101 actual exam dumps.
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
You always need actual and updated 350-101 exam questions to prepare the test successfully in less time. If you don't study with real Implementing and Operating Cisco Wireless Core Technologies (350-101) questions, you will ultimately fail and waste your money and time. To save yourself from this loss, you just need to prepare with updated Implementing and Operating Cisco Wireless Core Technologies (350-101) exam questions of LatestCram.
NEW QUESTION # 50
An engineer deploys a centralized wireless architecture using Cisco Catalyst 9800 controllers.
The customer requires APs to continue serving clients locally if WAN connectivity to the controller fails. Which AP mode best satisfies this requirement?
Answer: A
Explanation:
FlexConnect mode allows access points at remote sites to switch traffic locally while maintaining centralized management through the controller. During WAN outages, APs can continue authenticating clients locally and provide uninterrupted wireless access. Monitor and Sniffer modes are for analysis purposes, not client servicing or survivability operations.
NEW QUESTION # 51
Which result is produced using a power ratio of 10:1 in standard decibel calculations?
Answer: C
Explanation:
In decibel calculations, the formula used to convert a power ratio to decibels (dB) is:
Thus, the power ratio of 10:1 corresponds to a 10 dB change in power.
Option A: -20 dB would correspond to a ratio of 0.01:1, not 10:1.
Option B: 5 dB would correspond to a power ratio of approximately 3.16:1, not 10:1.
Option D: 15 dB would correspond to a ratio of 31.62:1, not 10:1.
Therefore, Option C: 10 dB is the correct answer, as it is the result of a power ratio of 10:1.
NEW QUESTION # 52
A network engineer must isolate all guest users connected to the WLAN on a Cisco 9800 WLC so they cannot communicate with each other but can access the internet. The WLAN must meet these requirements:
*SSID named VisitorAccess assigned to VLAN 30
*guests prohibited from sharing files with other guests
*must be scalable to multiple access points in the building
Which action must the network engineer take to meet the requirements?
Answer: B
Explanation:
The requirement is guest client isolation, not merely guest authentication or internet breakout. On a Catalyst
9800 WLC, peer-to-peer blocking is the correct control because it prevents wireless clients associated to the same WLAN from communicating directly with one another. Cisco defines peer-to-peer blocking as a WLAN security feature applied to individual WLANs, where each client inherits the WLAN's P2P blocking behavior, and traffic can be bridged locally, dropped, or forwarded upstream. For this scenario, the appropriate action is thedropbehavior, because guest-to-guest file sharing must be prohibited while upstream internet access remains available.
The dedicated guest VLAN, VLAN 30, provides traffic segmentation from production networks and creates a clean policy boundary for VisitorAccess. Cisco's Catalyst 9800 configuration model maps WLANs to policy profiles, and the policy profile defines client network and switching policy, including VLAN association.
Options B, C, and D do not solve client isolation: local authentication validates users, FlexConnect/local switching changes traffic forwarding behavior, and multicast/RADIUS does not block unicast guest-to-guest traffic. Reference topics:Client Connectivity Configuration - guest WLAN design, P2P blocking, VLAN segmentation, and Catalyst 9800 WLAN-to-policy mapping.
NEW QUESTION # 53
What is a characteristic of gain in wireless antenna design?
Answer: A
Explanation:
In wireless antenna design, gain refers to the measure of an antenna's ability to focus energy in a particular direction compared to a reference antenna, usually an isotropic radiator. Gain does not generate additional power; instead, it redistributes radiated energy to increase signal strength in the intended direction, enhancing the effective range and performance of the wireless link. This directional amplification is crucial in both point-to-point and point-to-multipoint deployments, as higher gain antennas can concentrate RF energy to overcome path loss and improve received signal strength at the target.
NEW QUESTION # 54
A network administrator at a construction company manages a Cisco Catalyst 9800 Series Wireless Controller running Cisco IOS XE 17.x. The WLAN named XYZ-Conference is set up for a large event, but attendees report slow network performance due to misbehaving clients. To improve connectivity, the network administrator decides to change the client exclusion policy on the WLAN to temporarily block the misbehaving clients. The XYZ-Conference WLAN must enable a client exclusion policy with a timeout of
120 seconds for misbehaving clients. Which set of Cisco IOS XE commands must be used?
Answer: A
Explanation:
Client exclusion is a feature in Cisco Catalyst 9800 WLCs that allows the administrator to temporarily block clients exhibiting misbehavior, such as excessive retries, excessive bandwidth usage, or roaming issues. The IOS XE CLI command for enabling client exclusion in a WLAN policy isclient-exclusion < timeout > , where
< timeout > defines the duration (in seconds) the client is prevented from associating with the WLAN. Option D correctly usesclient-exclusion 120to block the misbehaving clients for 120 seconds. Option A (exclude 120) is not valid IOS XE syntax. Option B (exclusionlist timeout 120) is also incorrect as it refers to internal exclusion lists, not the WLAN policy applied to live clients. Option C (security exclusion timeout 120) is invalid and does not configure client exclusion at the WLAN policy level. Cisco Wireless Core Technologies emphasize using client exclusion policies during high-density events or temporary network congestion to ensure network fairness, protect overall WLAN performance, and maintain connectivity for well-behaving clients. Reference topics:Client Connectivity Configuration - Client exclusion, WLAN policy, misbehaving client mitigation, Cisco Catalyst 9800 IOS XE.
NEW QUESTION # 55
......
Cisco 350-101 exam dumps are important because they show you where you stand. After learning everything related to the Implementing and Operating Cisco Wireless Core Technologies (350-101)certification, it is the right time to take a self-test and check whether you can clear the Implementing and Operating Cisco Wireless Core Technologies (350-101) certification exam or not. People who score well on the Implementing and Operating Cisco Wireless Core Technologies (350-101) practice questions are ready to give the final Implementing and Operating Cisco Wireless Core Technologies (350-101) exam.
350-101 Valid Exam Sample: https://www.latestcram.com/350-101-exam-cram-questions.html
P.S. Free 2026 Cisco 350-101 dumps are available on Google Drive shared by LatestCram: https://drive.google.com/open?id=14vcQrd5vM3hAnhr-lFN8pwXmv5BjVDBa