効率的なM2合格対策 &合格スムーズM2日本語参考 |ユニークなM2復習教材

M2認定の取得を支援するために、多くの専門家が数年間、International Code Councilすべての試験官向けのM2試験トレントを策定するために懸命に取り組んできました。Japancert このようにして、当社のM2学習資料は、対象となるだけでなく、すべての知識ポイントを網羅しています。 M2練習教材には、M2練習教材の学習プロセスの欠陥を見つけるのに役立つ統計分析機能もあるため、弱いリンクのCommercial Mechanical Inspectorトレーニングを強化できます。 このようにして、能力が向上したため、成功に自信を持つことができます。

International Code Council M2 Exam Syllabus Topics:

SectionObjectives
General Administration- Code Scope and Administration
  • 1. Referenced Standards
  • 2. Permits and Inspections
  • 3. Definitions
Hydronic Piping and Refrigeration- Hydronic Systems
  • 1. Piping Installation
  • 2. Pressure Testing
- Refrigeration
  • 1. Safety Controls
  • 2. Refrigerant Piping
Combustion Air and Fuel Supply- Fuel Supply Systems
  • 1. Fuel Oil Systems
  • 2. Fuel Gas Piping
- Combustion Air
  • 1. Combustion Air Openings
  • 2. Indoor and Outdoor Air Requirements
Chimneys and Vents- Connectors and Terminations
  • 1. Termination Requirements
  • 2. Vent Connectors
- Vent Systems
  • 1. Chimney Clearances
  • 2. Vent Sizing
Ventilation and Exhaust Systems- Commercial Kitchens
  • 1. Kitchen Exhaust Hoods
  • 2. Grease Ducts
- Ventilation
  • 1. Exhaust Air Systems
  • 2. Mechanical Ventilation
Heating and Cooling Systems- Cooling Systems
  • 1. Cooling Appliances
  • 2. Refrigeration Equipment
- Heating Appliances
  • 1. Water Heaters
  • 2. Boilers
  • 3. Furnaces
Materials and Specifications- Approved Materials
  • 1. Installation Standards
  • 2. Equipment Labeling
Duct Systems- Duct Construction
  • 1. Materials and Installation
  • 2. Dampers and Protection
- Air Distribution
  • 1. Plenums
  • 2. Duct Insulation

>> M2合格対策 <<

International Code Council M2日本語参考 & M2復習教材

Japancertの International Code CouncilのM2試験トレーニング資料を手に入れるなら、あなたは最も新しいInternational Code CouncilのM2学習教材を手に入れられます。Japancertの 学習教材の高い正確性は君がInternational Code CouncilのM2認定試験に合格するのを保証します。もしうちの学習教材を購入した後、商品は問題があれば、或いは試験に不合格になる場合は、私たちが全額返金することを保証いたします。

International Code Council Commercial Mechanical Inspector 認定 M2 試験問題 (Q28-Q33):

質問 # 28
Unless listed for a greater or smaller dimension, mechanical draft venting systems shall terminate a minimum of _____ feet below an openable window.

正解：A

解説：
For mechanical draft venting systems, unless the appliance is listed for a different clearance, the vent terminal must be located not less than 4 feet below , 4 feet horizontally from , or 1 foot above any door, operable window, or gravity air inlet into a building. Therefore, the required minimum distance below an openable window is 4 feet , so Option B is correct.


質問 # 29
Pipe and duct insulation can be used within plenums except:

正解：A

解説：
For materials such as pipe and duct insulation within plenums, the IMC references ASTM E84 or UL 723 for surface-burning characteristics, along with the flame-spread and smoke-developed limits applicable to plenums. ASTM B84 is not the referenced plenum test standard here, so it is the incorrect condition and therefore the correct exam answer to the "except" question. This makes Option C correct.


質問 # 30
Exhaust outlets that terminate at a temperature exceeding 600°F shall be designed as a:

正解：D

解説：
The IMC special exhaust provisions require exhaust outlets terminating at temperatures exceeding 600°F to be designed as a chimney , and the table language identifies this as a single-wall metal chimney . Therefore, Option D is correct.


質問 # 31
Where located on a roof with a 5:12 slope, a level platform shall be provided along the access panel of the furnace at least _____ inches wide.

正解：C

解説：
For appliances on roofs, ICC access provisions require a level platform at the appliance. The platform must be not less than 30 inches in any dimension . For the choices provided, that makes 30 inches the correct answer, which is Option C .


質問 # 32
When a furnace is installed in a 66-inch-high attic, the maximum distance from the passageway access to the furnace shall be _____ ft., measured along the centerline of the passageway.

正解：C

解説：
ICC mechanical access provisions for appliances in attics require the passageway to be not more than 20 feet in length , measured along the centerline of the passageway from the opening to the appliance, where the attic passageway is the standard reduced-height access condition. Since the attic height given is 66 inches, the standard maximum length applies, so Option C is correct. The 50-foot allowance applies only under a different exception where the passageway is unobstructed and at least 6 feet high for its entire length.


質問 # 33
......

我々のM2問題集に興味がありますか？ありましたら、Japancertのサイトで探しましょう。我々は弊社の商品の品質を保証しています。お客様は信じられないなら、我々の無料のM2サンプルをダウンロードして体験することができます。あなたの要求を満たすなら、我々のサイトでM2問題集を購入してください。

M2日本語参考: https://www.japancert.com/M2.html