93-Tall-Mass-Timber-Buildingsスタディガイドは無料のトライアルサービスを提供するため、スタディの内容、トピック、購入前にソフトウェアを最大限に活用する方法についての情報を入手できます。どのような93-Tall-Mass-Timber-Buildingsテスト準備が適切であるかを選択し、不必要な無駄を避けるために適切な選択をするのにInternational Code Council良い方法です。また、93-Tall-Mass-Timber-Buildings練習用トレントまたはトレイルプロセスの購入で問題が発生した場合は、すぐにご連絡いただければ、専門家がオンラインでお手伝いいたします。
| Section | Objectives |
|---|---|
| Tall Mass Timber Building Code Provisions | - Structural and Connection Requirements
- Special Inspection Requirements
|
>> 93-Tall-Mass-Timber-Buildings勉強の資料 <<
93-Tall-Mass-Timber-Buildingsの学習教材で20〜30時間準備したと主張することができます。93-Tall-Mass-Timber-Buildings試験に簡単に合格して、期待されるスコアを取得できます。 またInternational Code Council、93-Tall-Mass-Timber-Buildings試験問題の無料デモを提供しており、93-Tall-Mass-Timber-Buildingsトレーニング資料の有効性と正確性を確認できます。MogiExam やって来てみてください！ 93-Tall-Mass-Timber-Buildingsトレーニング資料の高い精度に驚かれることでしょう。 そして、93-Tall-Mass-Timber-Buildings練習問題集の高い合格率は99％から100％なので、93-Tall-Mass-Timber-Buildings試験に簡単に合格します。
質問 # 38
Sealants used to resist passage of air in construction Type IV-A, shall be in accordance with which of the following standards?
正解：C
解説：
ASTM C920 is the required standard for sealants used under the IBC mass timber air-sealing provision.
Option C is therefore correct. Section 703.7 applies to Type IV-A construction and requires compliant sealant or adhesive at specified interfaces involving fire-resistance-rated mass timber elements.
The sealing requirement reduces the movement of air, heat, and combustion gases into gaps that could expose additional timber surfaces and undermine the rated performance assumed by the approved design. The sealant must not merely appear to close the opening; it must be the specified product and installed within its approved joint dimensions and substrate conditions.
ASTM A36 is a structural steel material specification. ASTM E119 establishes procedures for fire testing building construction and assemblies but does not qualify elastomeric sealant products. ASTM F1667 covers driven fasteners such as nails, spikes, and staples and has no application to this sealing requirement.
Under Section 1705.20, installation is subject to periodic special inspection where the Section 703.7 sealant is applied. Inspection should occur before concealment and confirm continuity, adhesion, backing, joint depth, surface cleanliness, and compliance with the approved documents.
References/Topics: 2021 IBC Sections 703.7 and 1705.20; Type IV-A construction; ASTM C920.
質問 # 39
Buildings of Types IV-A, IV-B, and IV-C construction designed to be greater than six stories above grade plane shall meet which of the following requirements for fire safety practices during construction?
正解：A
解説：
Option A is an exact requirement of the 2021 International Fire Code Section 3303.5 . For Type IV-A, IV- B, and IV-C buildings designed to exceed six stories above grade plane, standpipes must be provided in accordance with IFC Section 3313, unless otherwise approved by the fire code official.
The IFC also requires a water supply for fire department operations, but that supply must be approved by the fire code official and fire chief; the code does not specifically mandate that it be a "portable" water supply.
Option B is therefore incorrect.
The remaining options alter important numerical requirements. Where noncombustible protection is required and construction exceeds six stories, at least one layer , not two, must be installed on applicable building elements more than four levels below active mass timber construction before additional floor levels are erected. Required exterior wall coverings are likewise required more than four levels below active mass timber construction, rather than two.
These safeguards reduce the amount of exposed combustible construction while ensuring that effective fire department infrastructure progresses with the building.
References/Topics: 2021 IFC Section 3303.5; Sections 3313 and related construction-stage fire protection requirements.
質問 # 40
Refer to the figure by clicking on the EXHIBIT button above.
In Type IV-B construction, unprotected portions of mass timber as shown in the Figure is limited to an area equal to not more than what percentage of the base floor area?
正解：B
解説：
The figure depicts an unprotected portion of the mass timber ceiling . For Type IV-B construction, Section
602.4.2.2.2, Exception 1.1, limits unprotected ceiling areas-including attached mass timber beams-to 20 percent of the floor area of the applicable dwelling unit or fire area. Option B is therefore correct.
The percentage is based on floor area rather than total ceiling surface area. For example, where the associated fire area contains 1,000 square feet of floor area, the maximum ceiling exposure permitted under this particular exception would be 200 square feet, subject to the additional separation and mixed-exposure provisions.
The 40-percent value in option D applies to mass timber walls, including attached columns , rather than ceilings. The 15-percent and 30-percent values are not the prescribed Type IV-B ceiling exposure limitations in the 2021 IBC.
The inspector must additionally determine whether another exposed wall or ceiling region exists nearby.
Section 602.4.2.2.4 imposes a 15-foot separation requirement, and Section 602.4.2.2.3 controls situations where both wall and ceiling surfaces are intentionally exposed.
References/Topics: 2021 IBC Sections 602.4.2.2.2 through 602.4.2.2.4; Type IV-B ceiling exposure limitations.
質問 # 41
Refer to the figure by clicking on the EXHIBIT button above.
The exterior wall section shown in the Figure provides the prescribed noncombustible protection required by which Construction Type?
正解：A
解説：
The illustrated wall corresponds to Type IV-A construction , making option A correct. The key indicator is the extensive Type X gypsum protection provided on the interior face of the CLT wall. Figure 63 shows multiple layers of 5/8-inch Type X gypsum board protecting the interior mass timber, together with the required exterior-side protection.
Type IV-A is the most comprehensively protected of the three tall mass timber construction classifications.
IBC Section 602.4.1.2 requires the interior faces of all mass timber elements , including the inside face of exterior mass timber walls, to be protected with qualifying noncombustible material. Section 602.4.1.2.1 requires the protection contribution to satisfy Table 722.7.1(1) and never be less than 80 minutes. Type IV-A exterior walls also require at least 40 minutes of noncombustible protection on the outside face.
The three interior layers shown are consistent with a heavily protected Type IV-A rated wall. By contrast, Type IV-B permits limited exposed interior mass timber, while Type IV-C expressly permits mass timber interior elements to remain unprotected. Type IV-HT operates under fundamentally different heavy-timber provisions.
References/Topics: 2021 IBC Sections 602.4.1.1, 602.4.1.2 and 602.4.1.2.1; Tables 601 and 722.7.1(1)-(2).
質問 # 42
Both surfaces of a two-hour-rated mass timber wall that serves as a required separation between a Group R and Group I-2 occupancy in a Type IV-C building must be protected by at least which of the following?
正解：A
解説：
The minimum additional protection is 1/2-inch gypsum board or an approved equivalent thermal barrier
, making option C correct.
The wall in the question functions as an occupancy separation. Under IBC Section 508.4.4.1, mass timber elements serving as fire barriers or horizontal assemblies separating occupancies in Type IV-B or IV-C construction must be separated from the building interior by an approved thermal barrier consisting of gypsum board at least 1/2 inch thick , or a material satisfying both applicable NFPA 275 thermal-barrier tests.
Because the wall separates two interior occupancies, each face is exposed to interior space; consequently, the thermal-barrier requirement applies to both surfaces .
This requirement must not be confused with the wall ' s two-hour fire-resistance rating. The underlying mass timber wall must independently satisfy the required two-hour assembly performance. The 1/2-inch gypsum protection is an additional thermal-barrier condition imposed because the rated separation is constructed of mass timber in Type IV-C.
Option D would provide substantially more gypsum protection than the specific occupancy-separation provision requires.
References/Topics: 2021 IBC Sections 508.4.4 and 508.4.4.1; Type IV-B/IV-C mass timber occupancy separations; approved thermal barriers; NFPA 275.
質問 # 43
......
弊社はお客様の皆様の利益を保証するために、あなたに高いクオリティのサービスを提供できて努力しています。今まで、弊社のMogiExamの93-Tall-Mass-Timber-Buildings問題集はそのスローガンに沿って協力します。弊社の信頼できる93-Tall-Mass-Timber-Buildings問題集を使用したお客様はほとんど試験に合格しました。
93-Tall-Mass-Timber-Buildings模擬対策問題: https://www.mogiexam.com/93-Tall-Mass-Timber-Buildings-exam.html