TheVCEPrep is one of the leading and reliable platforms that has been helping Designing Cisco Wireless Networks 300-110 exam candidates in their preparation. With high pass rate and Designing Cisco Wireless Networks 300-110 at a preferential price.To enhance your competitiveness in your field.
| Section | Weight | Objectives |
|---|---|---|
| Topic 1: Mobility | 25% | - Validate mobility tunneling - Design mobility groups - Optimize client roaming - Site Tags |
| Topic 2: WLAN High Availability | 20% | - Design controller high availability - Design AP high availability |
| Topic 3: Wired and Wireless Infrastructure | 30% | - Design wireless bridging (mesh) - Design for data, voice, video, location - Design high-density wireless networks - Design radio management - Logical infrastructure requirements - Physical infrastructure requirements |
| Topic 4: Wireless Site Survey | 25% | - Planning tools and network metrics evaluation - Layer 1 site survey analysis - Collect design requirements and evaluate constraints - Predictive site survey - Pre-deployment site survey - Material attenuation and its design effects - Post-deployment site survey |
>> 300-110 Test Preparation <<
VCEPrep is a website which always provide you the latest and most accurate information about Cisco certification 300-110 exam. In order to allow you to safely choose us, you can free download part of the exam practice questions and answers on VCEPrep website as a free try. VCEPrep can ensure you 100% pass Cisco Certification 300-110 Exam.
NEW QUESTION # 77
An engineer must design AP placements for a new branch office that contains two floors. The engineer uses Ekahau to complete the predictive survey. To calculate the signal bleed through between floors, the engineer creates a building, adds the floors, and attenuation areas. After the scale is set, what else must be added on the floors to accurately measure the signal bleed at a specific location?
Answer: A
Explanation:
In Ekahau Site Survey's multi-floor predictive modeling workflow, alignment points are the critical mechanism that allows the software to understand the precise vertical spatial relationship between floors in a multi-story building. Once floor plans are imported with their scale correctly defined, alignment points must be placed on each floor at the same real-world physical location -- such as a stairwell corner, elevator shaft, or structural column -- so that Ekahau can accurately calculate vertical signal propagation and inter-floor RF bleed. Without alignment points, the software has no spatial reference to determine which area on Floor 2 is directly above a given point on Floor 1, making floor-to-floor signal bleed calculations geometrically impossible.
NEW QUESTION # 78
A customer has two Cisco Catalyst 9800 Series WLCs named WLC-A and WLC-B in an N+1 configuration with the same WLANs but different Layer 3 interfaces for each WLC, and APs in local mode. WLC-A manages Building A APs and WLC-B manages Building B APs. The customer wants users to remain connected and retain their session state including the IP address when moving between buildings. How must this requirement be incorporated into the design?
Answer: D
Explanation:
The requirement for users to retain their session state and IP address when roaming between buildings managed by different WLCs is a Layer 3 roaming scenario. In Cisco's wireless architecture, IP address preservation across controller boundaries is achieved through inter- controller mobility -- specifically the foreign-anchor mobility tunnel mechanism. When a client roams from Building A (WLC-A) to Building B (WLC-B), WLC-B becomes the foreign controller and WLC-A becomes the anchor controller. WLC-B tunnels the client's traffic back to WLC-A, allowing the client to retain its original IP address even while physically associated to an AP managed by WLC-B. This requires a mobility tunnel between WLC-A and WLC-B with both controllers configured in the same mobility group name -- the group name is the trust identifier that permits the mobility tunnel and anchor- foreign relationship to form. Without the same group name, the controllers will not form a trusted mobility peer relationship.
NEW QUESTION # 79
A wireless consultant must design a Cisco WLAN. The consultant recommends a solution that requires 12 Cisco 9100 Series APs connected to a Cisco 3800 Series PoE+ switch. Each AP requires PoE+ for full functionality. What is the total PoE requirement in watts?
Answer: C
Explanation:
This question requires a straightforward PoE power budget calculation. The IEEE 802.3at standard (PoE+) delivers a maximum of 30W at the Power Sourcing Equipment (PSE/switch port). Cisco 9100 Series access points such as the C9120, C9130, and C9136 are designed to operate with full functionality using PoE+ at
30W per AP. The total PoE power requirement for 12 APs is calculated as: 12 APs Γ 30W per AP = 360W.
This figure represents the total power draw that the Cisco 3800 Series PoE+ switch must be capable of supplying across the connected AP ports simultaneously. The Cisco Catalyst 3800 Series switches offer a total PoE power budget that must be validated against this 360W requirement during the design phase. Note that some Cisco 9100 APs support higher power modes through IEEE 802.3bt (PoE++), which can provide up to
90W - but the question specifies PoE+ (802.3at) for the switch infrastructure, making 30W Γ 12 = 360W the correct answer. Option D (720W) would correspond to 24 APs at 30W each. Option B (1080W) would represent 36 APs. Option C (184.8W) corresponds to a non-standard per-AP power value. Reference: WLSD Study Guide - PoE Power Budget Planning, Cisco 9100 Series AP Power Requirements, Wired Infrastructure Design for Wireless Deployments.
NEW QUESTION # 80
An engineer is designing a point-to-point outdoor bridge link spanning 4 km between two buildings. Which two factors must be calculated during the design? (Choose two.)
Answer: A,E
Explanation:
An outdoor bridge link is fundamentally an RF engineering problem, and two calculations determine whether the link will work. Fresnel zone clearance (Option A) accounts for the ellipsoidal volume around the direct line of sight through which most of the RF energy travels; obstructions intruding into this zone cause diffraction loss even when visual line of sight appears clear. Cisco's design guidance is to maintain at least 60% of the first Fresnel zone free of obstruction, which at 4 km requires meaningful antenna height above terrain, buildings, and tree lines. The link budget (Option C) sums transmit power, antenna gain at both ends, cable and connector losses, and free-space path loss, then compares the result against receiver sensitivity for the desired data rate - with adequate fade margin, typically 10 to 20 dB, to survive rain and multipath. Mobility group names, DHCP scoping, and MTU are network configuration details that do not determine whether the RF link closes.
NEW QUESTION # 81
An engineer is conducting a Layer 2 site survey. Which type of client must the engineer match to the survey?
Answer: C
Explanation:
When conducting a Layer 2 site survey, it is recommended to match the survey to the worst client available. This ensures that the wireless network is designed to provide adequate coverage and performance even for clients with the poorest RF capabilities, thereby providing a consistent user experience for all devices. The worst client typically has fewer antennas, lower receiver sensitivity, and less sophisticated chipsets. By designing to its limitations, the engineer guarantees that every device in the environment meets the minimum performance threshold.
NEW QUESTION # 82
......
To ensure that you have a more comfortable experience before you choose to purchase our 300-110 exam quiz, we provide you with a trial experience service. Once you decide to purchase our 300-110 learning materials, we will also provide you with all-day service. If you have any questions, you can contact our specialists. We will provide you with thoughtful service. And you are boung to pass the 300-110 Exam with our 300-110 training guide. With our trusted service, our 300-110 learning materials will never make you disappointed.
300-110 New Braindumps Ebook: https://www.vceprep.com/300-110-latest-vce-prep.html