With TestkingPDF, you can trust that you're accessing authentic and error-free 300-110 exam practice questions. These questions are available in three different formats: PDF questions files, desktop practice test software, and web-based practice test software. All three formats contain genuine 300-110 Practice Questions that will effectively prepare you for the final exam.
| Section | Weight | Objectives |
|---|---|---|
| WLAN High Availability | 20% | - Design controller high availability - Design AP high availability |
| Wireless Site Survey | 25% | - Layer 1 site survey analysis - Predictive site survey - Planning tools and network metrics evaluation - Post-deployment site survey - Material attenuation and its design effects - Pre-deployment site survey - Collect design requirements and evaluate constraints |
| Wired and Wireless Infrastructure | 30% | - Design radio management - Design high-density wireless networks - Design wireless bridging (mesh) - Logical infrastructure requirements - Physical infrastructure requirements - Design for data, voice, video, location |
| Mobility | 25% | - Design mobility groups - Optimize client roaming - Site Tags - Validate mobility tunneling |
>> 300-110 Reliable Dumps Sheet <<
We believe that the greatest value of 300-110 study materials lies in whether it can help candidates pass the examination, other problems are secondary. And at this point, our 300-110 study materials do very well. We can proudly tell you that the passing rate of our 300-110 Study Materials is close to 100 %. That is to say, almost all the students who choose our products can finally pass the exam. We are not exaggerating because this conclusion comes from previous statistics.
NEW QUESTION # 85
A customer has 10 access point licenses available on their backup Cisco WLC and their primary Cisco WLC is at full capacity. 5 access points are set to high failover priority and 7 access points are set to critical failover priority. During a failure, not all critical access points failed over to the backup Cisco WLC. Which configuration is the cause of this issue?
Answer: B
Explanation:
The issue described indicates that there are more critical priority access points than the backup Cisco WLC can accommodate with its available AP licenses. The backup WLC has only 10 licenses available, but 7 APs are set to critical failover priority and 5 to high failover priority - a total of 12 APs attempting to join. Even though critical priority APs are processed before high priority APs, the backup WLC can only accept 10 APs total (its license limit). Since there are 7 critical priority APs and only 10 total licenses, all 7 critical APs will fail over successfully - but if the scenario involves additional critical APs beyond the license limit, the excess will not be able to join. The oversubscription of the critical priority AP count relative to available backup WLC capacity is the root cause. AP failover priority being disabled (Option D) would mean all APs have equal priority, not that critical APs fail to join. ' network ap-priority set to enable ' (Option B) enables the priority processing globally, which would be required for the feature to work at all. Reference: WLSD Study Guide - AP Failover Priority, N+1 Redundancy License Planning, WLC License Capacity Management.
NEW QUESTION # 86
An engineer is estimating the loss between two floors of an office building. Using Ekahau, they have measured -45 dBm at the ground level of the floor with the access point and -50 dBm at the ceiling level of the floor below it. Which value is the loss of the floor?
Answer: A
Explanation:
Floor loss calculation is a fundamental skill in multi-floor wireless site survey methodology. The floor attenuation value represents the signal power reduction caused by penetrating through a single floor structure including the floor decking, subfloor, ceiling material, plenum space, and any structural elements. In this measurement scenario, the engineer has two data points: -45 dBm measured at the ground level of the floor containing the access point (the signal level just below the AP ' s floor) and -50 dBm measured at the ceiling level of the floor below (the signal level just after passing through the floor structure). The floor loss is simply the difference between these two measurements: (-45 dBm) - (-50 dBm) = -45 + 50 = 5 dB. The result is expressed as a positive value (5 dB) representing attenuation - signal power decreases by 5 dB when passing through the floor. Expressing it as -5 dB (Option B) would incorrectly imply a signal gain. The 95 dB values (Options A and D) result from incorrectly adding rather than subtracting the dBm values - a common error when working with negative dBm figures. This floor attenuation value (5 dB) would then be entered into Ekahau ' s floor material properties to improve predictive model accuracy. Reference: WLSD Study Guide - Multi-Floor Signal Propagation, Floor Attenuation Factor (FAF), Ekahau Floor Loss Measurement Methodology.
NEW QUESTION # 87
A wireless engineer must design a WLAN for a university that requires outdoor Wi-Fi access. Which obstruction has the greatest effect on wireless signal propagation?
Answer: B
Explanation:
In outdoor wireless deployments, foliage - particularly dense trees - represents the most significant and variable RF obstruction that engineers must account for during site survey and design. Trees are problematic for multiple compounding reasons: the high water content of living tissue causes signal absorption consistent with the principle that water is an effective absorber of 2.4 GHz and 5 GHz RF energy; the irregular branching structure causes multi-path scattering; and foliage density changes seasonally, meaning signal propagation characteristics measured during winter may differ substantially from summer readings when leaves are fully developed. A fully leafed deciduous tree can attenuate a 5 GHz signal by 6-15 dB depending on density and depth. Wind (Option A) causes only momentary mechanical movement of foliage and is not an obstruction itself. Rain (Option B) causes some absorption at higher frequencies but its effect at 2.4 GHz and
5 GHz in typical conditions is marginal compared to foliage. Poles (Option D) are thin structures with minimal RF impact. Outdoor surveys for university campuses must specifically account for tree locations, canopy density, and seasonal variation. Reference: WLSD Study Guide - Outdoor Wireless Design, Environmental RF Attenuation Factors, Outdoor Site Survey Considerations.
NEW QUESTION # 88
An engineer is designing a high-density WLAN that must support 100 concurrent users with 100 Mbps throughput consistently. The design allows for 20 Mbps per cell and per channel on the 5 GHz band. How many channels must the design use to provide 1 Mbps per user prior to RF overhead?
Answer: C
Explanation:
This question requires straightforward wireless capacity engineering calculation. The total throughput requirement is 100 users ?1 Mbps per user = 100 Mbps aggregate. Each channel in the design can support 20 Mbps of usable throughput -- this is the per-cell, per-channel allocation defined in the design parameters, representing usable throughput prior to RF overhead as stated in the question. The number of channels required is therefore: total required throughput divided by throughput per channel = 100 Mbps ?20 Mbps per channel = 5 channels. In practice, each channel corresponds to a non-overlapping frequency assignment in the 5 GHz band. With 5 channels and 20 Mbps per channel, the design provides exactly 100 Mbps of aggregate capacity for 100 concurrent users at 1 Mbps each. This calculation methodology is foundational to Cisco's high-density WLAN design approach, where the number of spatial streams, channel allocations, and AP placement are all derived from the per-user throughput requirement multiplied by the concurrent user population.
NEW QUESTION # 89
An engineer must design AP placements for a new branch office that contains two floors. The engineer uses Ekahau to complete the predictive survey. To calculate the signal bleed through between floors, the engineer creates a building, adds the floors, and attenuation areas. After the scale is set, what else must be added on the floors to accurately measure the signal bleed at a specific location?
Answer: C
Explanation:
In Ekahau Site Survey's multi-floor predictive modeling workflow, alignment points are the critical mechanism that allows the software to understand the precise vertical spatial relationship between floors in a multi-story building. Once floor plans are imported with their scale correctly defined, alignment points must be placed on each floor at the same real-world physical location -- such as a stairwell corner, elevator shaft, or structural column -- so that Ekahau can accurately calculate vertical signal propagation and inter-floor RF bleed. Without alignment points, the software has no spatial reference to determine which area on Floor 2 is directly above a given point on Floor 1, making floor-to-floor signal bleed calculations geometrically impossible.
NEW QUESTION # 90
......
It can be said that all the content of the 300-110 prepare questions are from the experts in the field of masterpieces, and these are understandable and easy to remember, so users do not have to spend a lot of time to remember and learn. It takes only a little practice on a daily basis to get the desired results. Especially in the face of some difficult problems, the user does not need to worry too much, just learn the 300-110 Practice Guide provide questions and answers, you can simply pass the exam. This is a wise choice, and in the near future, after using our 300-110 exam braindumps, you will realize your dream of a promotion and a raise, because your pay is worth the rewards.
300-110 New Dumps Free: https://www.testkingpdf.com/300-110-testking-pdf-torrent.html