For candidates who are going to buying 93-Tall-Mass-Timber-Buildings exam materials, the pas rate for the exam is quite important, and it will decide whether you can pass your exam successfully or not. Pass rate for is 98.65% for 93-Tall-Mass-Timber-Buildings exam materials, and if you choose us, we can help you pass the exam just one time. In addition 93-Tall-Mass-Timber-Buildings Exam Materials are high quality and accuracy, and they can improve your efficiency. We are pass guarantee and money back guarantee for 93-Tall-Mass-Timber-Buildings exam dumps, if you fail to pass the exam, we will give you full refund.
| Section | Objectives |
|---|---|
| Topic 1: Code Compliance and Related Requirements | - Sound transmission requirements - Documentation and verification of compliance - Energy code requirements applicable to mass timber buildings |
| Topic 2: Structural Inspection | - Structural loads and related code requirements - Connections and fastening systems - Mass timber structural elements |
| Topic 3: Tall Mass Timber Building Code Provisions | - International Building Code requirements for tall mass timber construction - Types IV-A, IV-B and IV-C construction - Mass timber materials and construction requirements |
| Topic 4: Special Inspection Requirements | - Inspector duties and responsibilities - Inspection of connections and protective materials - Special inspection procedures for tall mass timber buildings |
| Topic 5: Fire Protection and Fire-Resistance | - Fire-resistance requirements - Noncombustible protection and protection of mass timber elements - Fire protection systems and related provisions |
| Topic 6: Construction Fire Safety | - International Fire Code requirements - Construction-phase fire safety requirements - Protection of mass timber during construction |
>> Valid 93-Tall-Mass-Timber-Buildings Exam Test <<
Dumpcollection's International Code Council exam practice test content is tested and approved by the best industry experts and is constantly updated to meet the requirements of the actual 93-Tall-Mass-Timber-Buildings exam questions. Dumpcollection reputation is established particularly with an outstanding success rate of 99.1%. This boosts up our popularity graph among the ambitious professionals who want to enrich their profiles with the most prestigious 93-Tall-Mass-Timber-Buildings certifications. Above all, your success is ensured with 100% Dumpcollection money back guarantee. If our 93-Tall-Mass-Timber-Buildings test dumps do not help you pass exam paper, we shall refund your money in full.
NEW QUESTION # 15
Refer to the exhibit by clicking on the EXHIBIT button above.
In the detail shown, which fasteners require fire protection according to AWC Technical Report 10?
Answer: B
Explanation:
The 1/2-inch lag screws attaching the structural steel ledger require fire protection, making option D correct. These fasteners are structural components of the ledger-to-CLT connection and therefore form part of the connection whose fire performance must be maintained for the required duration.
AWC Technical Report 10 states that wood structural connections-including their connectors, fasteners, and participating members-must be protected from fire exposure for the required fire-resistance time
. Protection may be provided by wood cover, fire-rated gypsum board, other approved materials, or a combination.
TR10 distinguishes structural connection fasteners from small fasteners used merely to hold sacrificial protection in place. The report specifically explains that fasteners attaching protective wood strips need not themselves be protected, provided they are sufficiently long to keep the protection in position throughout the required exposure.
In the illustrated ledger connection, the 1/2-inch lag screws transfer structural load between the steel ledger and CLT wall. Their thermal protection is therefore integral to maintaining connection capacity.
References/Topics: AWC Technical Report No. 10 Sections 4.5 and connection examples; thermal protection of structural connectors and fasteners.
NEW QUESTION # 16
The International Building Code requires cross-laminated timber (CLT) to be manufactured and identified in accordance with which standard?
Answer: C
Explanation:
The governing standard is ANSI/APA PRG 320, Standard for Performance-Rated Cross-Laminated Timber.
Therefore, option A is correct. The 2021 IBC requires structural glued cross-laminated timber to be manufactured and identified in accordance with PRG 320, and Type IV provisions require CLT to bear a label demonstrating conformity with that standard.
PRG 320 addresses essential manufacturing and qualification requirements, including panel construction, layup, structural performance, adhesive qualification, dimensional tolerances, product marking and quality assurance. Product identification is particularly important to the special inspector because visual similarity alone does not establish that a panel is code compliant.
DOC PS 2 applies primarily to wood structural panels such as plywood and oriented strand board and is not the manufacturing standard for CLT. ANSI/AITC or ANSI/APA A190.1 applies to structural glued-laminated timber, commonly called glulam. ASTM D5055 covers the establishment and monitoring of structural capacities for prefabricated wood I-joists.
The inspector should verify that CLT panels retain legible identification and that the manufacturer, grade, layup and panel designation correspond to the approved construction documents.
References/Topics: 2021 IBC Sections 602.4 and 2303.1.4; Chapter 35; ANSI/APA PRG 320-2019.
NEW QUESTION # 17
Refer to the figure by clicking on the EXHIBIT button above.
In Type IV-B construction, unprotected portions of mass timber as shown in the Figure is limited to an area equal to not more than what percentage of the base floor area?
Answer: C
Explanation:
The highlighted exposed surfaces in this figure are mass timber wall surfaces . Under 2021 IBC Section
602.4.2.2.2, Exception 1.2, unprotected portions of Type IV-B mass timber walls, including attached columns, are permitted up to an area equal to 40 percent of the floor area in the applicable dwelling unit or fire area.
Option D is therefore correct.
This should be distinguished from the corresponding ceiling limitation. Unprotected mass timber ceilings, including attached beams, are limited to 20 percent of floor area. The larger 40-percent allowance applies specifically to wall exposure.
Where only wall surfaces are exposed, the allowable wall area is calculated directly from the base floor area.
For example, a 1,000-square-foot fire area would permit up to 400 square feet of exposed wall surface under this exception. However, Section 602.4.2.2.4 additionally requires unprotected wall portions to maintain the prescribed 15-foot separation from other applicable exposed wall or ceiling portions.
Where exposed walls and exposed ceilings occur together, the individual 40- and 20-percent limits cannot simply be maximized simultaneously; the mixed-exposure equation in Section 602.4.2.2.3 governs.
References/Topics: 2021 IBC Sections 602.4.2.2.2 through 602.4.2.2.4; Type IV-B wall exposure.
NEW QUESTION # 18
Combustible construction forming concealed spaces shall be protected with noncombustible protection with an assigned time of 40 minutes in which construction type?
Answer: B
Explanation:
The requirement applies to Type IV-C construction. Under the 2021 IBC provisions governing Type IV-C, combustible construction forming concealed spaces must be protected with noncombustible protection having an assigned protection time of not less than 40 minutes. Therefore, option C is correct.
The assigned protection time is determined using the protection-time values prescribed by the code, including the applicable values for gypsum board and other approved noncombustible materials. The provision is intended to delay ignition and involvement of combustible mass timber surfaces located within concealed spaces, where fire growth might otherwise remain undetected and become difficult for fire-suppression personnel to access.
Type IV-A and Type IV-B are subject to more extensive noncombustible protection requirements because those construction types support taller buildings and require greater protection of mass timber elements. Type IV-HT uses the traditional heavy-timber concealed-space provisions and may employ alternative methods, such as complete filling with noncombustible insulation.
During inspection, the special inspector must confirm that the installed layers, thicknesses, fastening patterns, joints, penetrations, and transitions collectively provide the required 40-minute assigned protection time.
References/Topics: 2021 IBC Section 602.4.3.5; Table 722.7.1(1); Type IV-C concealed-space protection.
NEW QUESTION # 19
Given: A special inspector notices on a mass timber building set of drawings a 8 in. x 8 in. solid sawn nominal dimension lumber element.
The design team has recommended the solid sawn member be replaced with an SCL element.
What minimum SCL size would be correct per the International Building Code?
Answer: A
Explanation:
The IBC does not require structural composite lumber to retain the same nominal dimensions as the solid- sawn member it replaces. Instead, the minimum finished dimensions are determined from the heavy-timber dimensional equivalency provisions in Section 2304.11.
For a solid-sawn member having nominal dimensions of 8 inches by 8 inches, the corresponding minimum structural composite lumber net dimensions are 7 inches in width by 7-1/2 inches in depth. Therefore, option B is correct. The dimensional conversion recognizes that nominal solid-sawn dimensions differ from actual manufactured dimensions and that SCL products are produced to controlled net dimensions.
The 6-3/4-inch by 8-1/4-inch dimensions in option C correspond to the minimum glued-laminated timber equivalency for an 8-inch-by-8-inch nominal solid-sawn member, not the SCL equivalency. Option D incorrectly assumes that the SCL member must retain the original nominal dimensions, while option A does not match the required equivalency for either SCL or glued-laminated timber.
The substitution must also be approved by the registered design professional because dimensional compliance alone does not establish equivalent structural capacity, connection behavior, fire resistance, or load-path performance.
References/Topics: 2021 IBC Section 2304.11; heavy-timber minimum dimensions; minimum structural composite lumber net-size table.
NEW QUESTION # 20
......
Sometimes, you may worry about too much on the 93-Tall-Mass-Timber-Buildings exam and doubt a lot on the 93-Tall-Mass-Timber-Buildings exam questions. But if your friends or other familiar people passed the exam, you may be more confident in his evaluation. In any case, our common goal is to let you pass the exam in the shortest possible time! And we can proudly claim that if you study with our 93-Tall-Mass-Timber-Buildings Training Materials for 20 to 30 hours, then you can pass the exam with ease. And it is the data provided and tested by our worthy customers!
93-Tall-Mass-Timber-Buildings Free Test Questions: https://www.dumpcollection.com/93-Tall-Mass-Timber-Buildings_braindumps.html