Right Q&A in Juniper JN0-364 Exam Questions

DOWNLOAD the newest ActualtestPDF JN0-364 PDF dumps from Cloud Storage for free: https://drive.google.com/open?id=1FseAxza-VIPhRnS_Hnx0P_bVlOrWoRwH

Our company was built in 2008 since all our education experts have more than ten years' experience in JN0-364 guide torrent. The most important characters we pay attention on are our quality and pass rate. We devote ourselves to improve passing rate constantly and service satisfaction degree of our JN0-364 training guide. And now you can find the data provided from our loyal customers that our pass rate of JN0-364 learning guide is more than 98%. You will successfully pass your JN0-364 exam for sure.

Juniper JN0-364 Exam Syllabus Topics:

SectionObjectives
Border Gateway Protocol (BGP)- Identify the concepts, operation, or functionality of BGP
  • 1. BGP basic operation
  • 2. IBGP and EBGP functionality and interaction
  • 3. BGP message types
  • 4. BGP route reflection and confederations
  • 5. Route selection process
  • 6. Attributes
- Demonstrate knowledge of how to configure, monitor, or troubleshoot BGP
  • 1. Routing policy application
  • 2. Peers and peer groups
  • 3. Troubleshooting tools
IPv6- Identify the concepts, operation, or functionality of IPv6
  • 1. Static routes
  • 2. IPv6 over IPv4 tunneling
  • 3. Dynamic routing - OSPFv3, IS-IS, BGP
- Demonstrate knowledge of how to configure, monitor, or troubleshoot IPv6
Layer 2 Bridging or VLANs- Identify the concepts, benefits, or functionality of VLANs
  • 1. Integrated Routing and Bridging (IRB)
  • 2. Port modes
  • 3. Tagging
- Demonstrate knowledge of how to configure, monitor, or troubleshoot Layer 2 bridging or VLANs
  • 1. Interfaces and ports
  • 2. Provider bridging
  • 3. IRB
  • 4. VLANs
- Identify the concepts, operation, or functionality of Layer 2 bridging for the Junos OS
  • 1. Provider bridging (Q-in-Q tunneling)
  • 2. Bridging elements and terminology
  • 3. Virtual Switches
  • 4. Frame processing
  • 5. Service provider switching platforms
Protocol-Independent Routing- Identify the concepts, operation, or functionality of various protocol-independent routing components
  • 1. Routing instances, including routing information base (RIB) (also known as routing table) group
  • 2. Martian addresses
  • 3. Load balancing
  • 4. Static, aggregate, and generated routes
  • 5. Filter-based forwarding
- Demonstrate knowledge of how to configure, monitor, or troubleshoot various protocol-independent routing components
  • 1. Load balancing
  • 2. Static, aggregate, and generated routes
  • 3. Filter-based forwarding
Spanning Tree Protocols- Identify the concepts, operation, or functionality of STP
  • 1. VSTP
  • 2. RSTP
  • 3. STP
  • 4. MSTP
- Demonstrate knowledge of how to configure, monitor, or troubleshoot Spanning Tree Protocols
  • 1. VSTP
  • 2. RSTP
  • 3. STP
  • 4. MSTP
Intermediate System to Intermediate System (IS-IS)- Identify the concepts, operation, or functionality of IS-IS
  • 1. IS-IS protocol data units (PDUs)
  • 2. Link-state database
  • 3. Designated intermediate system (DIS)
  • 4. Type, length, values (TLVs)
  • 5. Adjacencies and neighbors
  • 6. Levels and areas
  • 7. Metrics
- Demonstrate knowledge of how to configure, monitor, or troubleshoot IS-IS
  • 1. Routing policy application
  • 2. Interfaces and adjacencies
  • 3. Troubleshooting tools
Open Shortest Path First (OSPF)- Demonstrate knowledge of how to configure, monitor, or troubleshoot OSPF
  • 1. Routing policy application
  • 2. Interfaces and neighbor
  • 3. Troubleshooting tools
- Identify the concepts, operation, or functionality of OSPF
  • 1. Designated router and backup designated router
  • 2. Link-state database
  • 3. Link-state advertisement (LSA) packet type
  • 4. OSPF packet types
  • 5. Adjacencies and neighbors
  • 6. Router ID
  • 7. OSPF area and router types
Multiprotocol Label Switching (MPLS)- Demonstrate knowledge of how to configure, monitor, or troubleshoot MPLS
  • 1. MPLS forwarding
  • 2. Shortest path segment-routing LSPs
  • 3. RSVP-signaled Label-Switched Paths (LSPs)
  • 4. LDP-signaled Label-Switched Paths (LSPs)
- Identify the concepts, operation, or functionality of MPLS CoS processing on Junos devices
  • 1. End-to-end packet flow and forwarding
  • 2. LDP
  • 3. Labels and the label information base
  • 4. MPLS packet header
  • 5. MPLS terminology
  • 6. RSVP
  • 7. Segment routing with MPLS
  • 8. MPLS and routing tables

>> Pdf JN0-364 Free <<

Juniper JN0-364 Practice Test - The Key To Fast Exam

You may previously think preparing for the JN0-364 practice exam will be full of agony; actually, you can abandon the time-consuming thought from now on. Our JN0-364 exam question can be obtained within 5 minutes after your purchase and full of high quality points for your references, and also remedy your previous faults and wrong thinking of knowledge needed in this exam. As a result, many customers get manifest improvement and lighten their load by using our JN0-364 latest dumps. You won’t regret your decision of choosing us. In contrast, they will inspire your potential. Besides, when conceive and design our JN0-364 Exam Questions at the first beginning, we target the aim customers like you, a group of exam candidates preparing for the exam. Up to now, more than 98 percent of buyers of our JN0-364 latest dumps have passed it successfully. Up to now they can be classified into three versions: the PDF, the software and the app version. So we give emphasis on your goals, and higher quality of our JN0-364 test guide.

Juniper Service Provider Routing and Switching, Specialist (JNCIS-SP) Sample Questions (Q174-Q179):

NEW QUESTION # 174
Click the Exhibit button.

Referring to the exhibit, which protocol would automatically create a full mesh of label-switched paths between MPLS-enabled routers?

Answer: B

Explanation:
LDP automatically establishes label-switched paths between all MPLS-enabled routers that share IGP reachability. It distributes labels for IGP prefixes and uses the existing IGP topology to build LSPs dynamically, effectively creating a full mesh of LSPs across the MPLS network without requiring explicit configuration.


NEW QUESTION # 175
Referring to the exhibit, internal BGP between R1 and R2 is not establishing.
What is the problem In this scenario?

Answer: A

Explanation:
The exhibit shows that the BGP session state is "Active," which generally indicates that the router is trying to establish a BGP session but has not received a response. One common cause for this issue is that there is no route to the BGP neighbor's address. Since the routers are using internal BGP (iBGP) and they are in the same AS, the AS number does not need to be unique, and a next-hop self policy is not strictly required for iBGP. The router-id is usually automatically determined and does not need to be explicitly set.


NEW QUESTION # 176
Which new field is added to an IPv6 header as compared to IPv4?

Answer: D

Explanation:
The flow label is a new field added to IPv6 headers that was not present in IPv4 headers. It is used to identify packets that require special handling by routers, particularly for quality-of-service (QoS) purposes.


NEW QUESTION # 177
Referring to the exhibit. You are advertising a summary route that represents your local network (172.20.0.0716) to both ISP A and ISPB. You want to influence all traffic sent to you from ISP C to go through R2.
How would you accomplish this task?

Answer: D

Explanation:
To influence ISP C to prefer the path through R2 for the 172.20.0.0/16 network, R2 should make its path less preferable to ISP B by prepending its AS number multiple times. This makes the path through R2 appear longer and less desirable to ISP C, which would receive these updates from ISP B. AS path length is a well-known attribute in BGP and is used to determine the best path; paths with a longer AS path are considered less preferable.


NEW QUESTION # 178
You are asked to configure the OSPF environment to prevent the DRother routers from participating in DR/BDR election.
Referring to the exhibit, which command will accomplish this task?

Answer: A

Explanation:
To prevent a router from participating in the OSPF designated router (DR) and backup designated router (BDR) election process, you set the OSPF priority to 0 on the interfaces of that router. This tells OSPF that the router on those interfaces is not to be considered for election as either DR or BDR, effectively making them DRother routers. The exhibit indicates that this is the desired configuration, and therefore the correct command to issue on the Juniper device would be to set the priority to 0 on the relevant interfaces.


NEW QUESTION # 179
......

After using our JN0-364 learning materials, you will find that things that have been difficult before have become simple. Of course, that's because you are better. Opportunities are for those who are prepared. And our JN0-364 exam questions are the right tool to help you get prepared. With the most up-to-date knowledage and information of the JN0-364 Practice Braindumps, you can be capable to deal with all of the conditions in your job. Believe it, good people will be better!

JN0-364 Test Questions Pdf: https://www.actualtestpdf.com/Juniper/JN0-364-practice-exam-dumps.html

BTW, DOWNLOAD part of ActualtestPDF JN0-364 dumps from Cloud Storage: https://drive.google.com/open?id=1FseAxza-VIPhRnS_Hnx0P_bVlOrWoRwH