P.S. Free 2026 Juniper JN0-351 dumps are available on Google Drive shared by DumpsActual: https://drive.google.com/open?id=1EwQussZ9894qTU0jvxKdjFteSk3Nxsrk
As long as you follow the steps of our JN0-351 quiz torrent, your mastery of knowledge will be very comprehensive and you will be very familiar with the knowledge points. This will help you pass the exam more smoothly. The JN0-351 learning materials are of high quality, mainly reflected in the adoption rate. As for our JN0-351 exam question, we guaranteed a higher passing rate than that of other agency. More importantly, we will promptly update our JN0-351 Quiz torrent based on the progress of the letter and send it to you. 99% of people who use our JN0-351 quiz torrent has passed the exam and successfully obtained their certificates, which undoubtedly show that the passing rate of our JN0-351 exam question is 99%. So our product is a good choice for you. Choose our JN0-351 learning materials, you will gain a lot and lay a solid foundation for success.
| Section | Objectives |
|---|---|
| Topic 1: Layer 2 Switching and VLANs | - Inter-VLAN routing - Configuration, monitoring and troubleshooting - VLAN concepts, tagging, ports, native VLAN - Layer 2 switching concepts and operation |
| Topic 2: Tunnels | - Configuration, monitoring and troubleshooting - IP-IP, GRE, IPsec tunnels |
| Topic 3: BGP | - Configuration, monitoring and troubleshooting - IBGP, EBGP, route policies - BGP concepts, attributes, path selection |
| Topic 4: Spanning Tree Protocol | - Root bridge, port roles and states - Configuration, monitoring and troubleshooting - STP, RSTP, MSTP concepts and operation |
| Topic 5: Layer 2 Security | - Configuration, monitoring and troubleshooting - Dynamic ARP inspection, DHCP snooping - Layer 2 firewall filters - Port security, storm control, MAC limiting |
| Topic 6: High Availability | - Virtual Chassis, redundant routing engines - Configuration, monitoring and troubleshooting - Graceful restart, nonstop active routing |
| Topic 7: Protocol Independent Routing | - Static routes, aggregate routes - Routing tables, routing preferences - Configuration, monitoring and troubleshooting - Routing policy and firewall filters |
| Topic 8: IS-IS | - IS-IS concepts, levels, routing information - Configuration, monitoring and troubleshooting |
| Topic 9: OSPF | - Configuration, monitoring and troubleshooting - OSPFv2/v3 concepts, areas, LSA types - Neighbor relationships, route calculation |
>> JN0-351 Test Questions Fee <<
DumpsActual is a website that can provide all information about different IT certification exam. DumpsActual can provide you with the best and latest exam resources. To choose DumpsActual you can feel at ease to prepare your Juniper JN0-351 exam. Our training materials can guarantee you 100% to pass Juniper certification JN0-351 exam, if not, we will give you a full refund and exam practice questions and answers will be updated quickly, but this is almost impossible to happen. DumpsActual can help you pass Juniper Certification JN0-351 Exam and can also help you in the future about your work. Although there are many ways to help you achieve your purpose, selecting DumpsActual is your wisest choice. Having DumpsActual can make you spend shorter time less money and with greater confidence to pass the exam, and we also provide you with a free one-year after-sales service.
NEW QUESTION # 46
Referring to the exhibit, which two configuration changes must you apply for packets to reach from R1 to R3 using IS-IS? (Choose two.)
Answer: B,D
Explanation:
A) On R1, enable Level 1 on the ge-0/0/1 interface. In IS-IS, both levels (Level 1 and Level 2) are enabled by default when you enable IS-IS on an interface1. Level 1 systems route within an area.
If the destination is outside an area, Level 1 systems route toward a Level 2 system. Therefore, enabling Level 1 on the ge-0/0/1 interface on R1 would allow packets to reach from R1 to R3.
D) On R3 enable Level 1 on the ge-0/0/4 interface Similarly, enabling Level 1 on the ge-0/0/4 interface on R3 would allow packets to reach from R1 to R3. These explanations are based on the IS-IS configuration documents and learning resources available at Juniper Networks1 and Cisco.
NEW QUESTION # 47
Exhibit
Referring to the exhibit, which statement is correct?
Answer: B
Explanation:
Explanation
In a Rapid Spanning Tree Protocol (RSTP) topology, the root bridge is determined by the switch with the lowest bridge priority value12. If all switches have the same priority, then the root bridge is assigned to the switch whose MAC address's hex value is the lowest2. The default bridge priority value is 3276832. However, without the actual exhibit, it's difficult to definitively determine which device is the root bridge. But based on the options provided, if we assume that the local device has a lower bridge priority or a lower MAC address than other devices in the network, then it could be considered as the root bridge for this RSTP topology45.
NEW QUESTION # 48
You are troubleshooting a BGP routing issue between your network and a customer router and are reviewing the BGP routing policies. Which two statements are correct in this scenario?
(Choose two.)
Answer: C,D
Explanation:
In BGP, routing policies are used to control the flow of routing information between BGP peers.
Option C suggests that import policies are applied after the RIB-In table. This is correct because import policies in BGP are applied to routes that are received from a BGP peer, before they are installed in the local BGP Routing Information Base (RIB-In). The RIB-In is a database that stores all the routes that are received from all peers.
Option D suggests that export policies are applied after the RIB-Local table. This is correct because export policies in BGP are applied to routes that are being advertised to a BGP peer, after they have been selected from the local BGP Routing Information Base (RIB-Local). The RIB-Local is a database that stores all the routes that the local router is using.
NEW QUESTION # 49
You are asked to explore adding BGP route reflectors to allow for increased scale in your core network. Which statement is correct in this scenario?
Answer: B
NEW QUESTION # 50
What is the default keepalive time for BGP?
Answer: B
Explanation:
The default hold-time is 90 seconds, meaning that the default frequency for keepalive messages is 30 seconds.
https://www.juniper.net/documentation/us/en/software/junos/bgp/topics/ref/statement/precision- timers-edit-protocols- bgp.html#:~:text=BGP%20on%20the%20local%20routing,keepalive%20messages%20is%2030
%20seconds
NEW QUESTION # 51
......
We have three versions of JN0-351 practice questions for you to choose: PDF version, Soft version and APP version. PDF version of JN0-351 training materials is legible to read and remember, and support printing request, so you can have a print and practice in papers. Software version of JN0-351 practice materials supports simulation test system, and give times of setup has no restriction. Remember this version support Windows system users only. App online version of JN0-351 Exam Questions is suitable to all kinds of equipment or digital devices and supportive to offline exercise on the condition that you practice it without mobile data.
Practice Test JN0-351 Pdf: https://www.dumpsactual.com/JN0-351-actualtests-dumps.html
P.S. Free 2026 Juniper JN0-351 dumps are available on Google Drive shared by DumpsActual: https://drive.google.com/open?id=1EwQussZ9894qTU0jvxKdjFteSk3Nxsrk