P.S. Free & New Civil-Engineering-Technology dumps are available on Google Drive shared by PassSureExam: https://drive.google.com/open?id=1rckjn1tvsqUUikK3QDCbTfAwwyOqK08F
Up to now we classify our Civil-Engineering-Technology exam questions as three different versions. They are pdf, software and the most convenient one APP online. Though the content of these three versions is the same, but their displays are different. Each of them has their respective feature and advantage including new information that you need to know to pass the Civil-Engineering-Technology test. So you can choose the version of Civil-Engineering-Technology training quiz according to your personal preference.
| Section | Weight | Objectives |
|---|---|---|
| Transportation Engineering | 20% | - Traffic engineering
|
| Municipal Engineering | 20% | - Wastewater and stormwater management
|
| Surveying | 20% | - Measurement and calculation techniques
|
| Materials Testing | 20% | - Concrete and asphalt testing
|
| Structural Design Fundamentals | 20% | - Structural analysis
|
>> Civil-Engineering-Technology Valid Exam Camp <<
Our company will promptly update our Civil-Engineering-Technology exam materials based on the changes of the times and then send it to you timely. 99% of people who use our learning materials have passed the exam and successfully passed their certificates, which undoubtedly show that the passing rate of our Civil-Engineering-Technology Test Torrent is 99%. If you fail the exam, we promise to give you a full refund in the shortest possible time. So our product is a good choice for you. Choosing our Civil-Engineering-Technology study tool can help you learn better. You will gain a lot and lay a solid foundation for success.
NEW QUESTION # 45
A contractor is checking final grade elevation in advance of paving operations. What elevation needs to be confirmed before any asphalt is placed?
Answer: D
Explanation:
Before asphalt paving, the immediate supporting layer must be at the correct line and grade because asphalt thickness is builton top of the prepared base. Thetop of baseelevation controls final pavement structure thickness and the finished riding surface elevation when combined with asphalt lift thicknesses. If base grade is too high or low, the asphalt thickness will vary outside tolerance, which can affect performance (rutting, cracking), drainage crossfall, and tie-ins at structures and curbs. Standard field inspection practice therefore verifies base course elevations (and crossfall) immediately before paving so corrections (regrading
/recompaction) can be made while accessible. This fits typical roadway QA/QC sequencing: shape and compact subgrade/base to the specified elevations, confirm, then place asphalt lifts to achieve final grade.
Hence, the elevation that must be confirmed prior to placing asphalt istop of base.
NEW QUESTION # 46
A civil engineering technologist is taking a sample of concrete cylinders from a truck. When should the sample be taken?
Answer: B
Explanation:
Concrete cylinder samples must represent thedelivered batch, so sampling must avoid the non-representative portions at the beginning and end of discharge where segregation and water/aggregate distribution can differ.
ASTM C172/C172M sampling practice requires collecting acomposite samplefrom themiddle portionof the load: specifically, not before about10%and not after about90%of the batch has been discharged, using two or more portions taken at regularly spaced intervals. A paper hosted by ASTM discussing sampling from truck mixers references ASTM C172/C172M and its requirement for collecting multiple portions from the discharged batch. Training/field guidance consistent with ASTM C172 also states sampling should occur after
~10% and before ~90% of discharge (i.e., the middle of the load). Therefore, the correct answer isin the middle of the load (Option C).
NEW QUESTION # 47
What type of survey stake is shown in the image below?
Answer: C
Explanation:
Acentreline stakeis used to mark the roadway/control alignment in the field, typically at stations, and is identified by centreline-related notation rather than cut/fill or slope-to-daylight information. In the image, the stake is marked in a way consistent withcentreline stationing/control(as opposed to slope stakes, which typically include slope ratio, offset, and cut/fill to finished grade, or benchmark stakes, which serve as elevation control points). Standard construction staking guidance notes that stake markings communicate what line is being staked (e.g.,CL) and its relationship to stationing and control.
Because the stake is presented as a control point for alignment (centreline) rather than a grade/slope instruction, it is best classified as acentreline stake.
NEW QUESTION # 48
Based on the diagram below, what is the percentage slope between D1 and C2 if the grid is 10 m × 10 m?
Answer: B
Explanation:
Percent slope is computed as:
This is the standard civil engineering definition of grade/slope used in surveying, drainage, and roadway work. With a 10 m × 10 m grid, the plan distance between two grid points is determined from the grid spacing (10 m increments). Using the elevations/contours shown at pointsD1andC2, the elevation difference divided by the plan distance yields a slope that matches6.79%. This corresponds to a rise/fall of roughly0.679 m per
10 mof horizontal distance (or an equivalent ratio based on the exact D1-C2 spacing in the grid), which is consistent with the computed percent. Therefore, the correct selection is6.79% (Option C).
NEW QUESTION # 49
A subcontractor is completing surface rehabilitation in a mature community. What are the minimum requirements for quality that must be met?
Answer: D
Explanation:
In municipal surface rehabilitation, the governing minimum quality requirements are set by themunicipality's standards/specifications, because the work interfaces with, affects, and is often handed over to municipal infrastructure (roads, sidewalks, utilities, drainage). Municipal specifications define accepted materials, compaction/density requirements, asphalt/concrete placement tolerances, testing frequency, restoration details, and acceptance criteria. Contractor or subcontractor internal specs may exceed municipal requirements, and warranties/insurance address risk allocation, but they do not replace theowner/authority's technical acceptance standards. In civil engineering practice, "specifications" are the formal technical requirements that the delivered system must meet (minimum/maximum/range), including items like minimum density of roadbed, tolerances, and material performance-these are typically established by the owning agency (here, the municipality) for public infrastructure assets. Thus, the minimum quality threshold is defined by themunicipality specifications.
NEW QUESTION # 50
......
Civil-Engineering-Technology test questions have so many advantages that basically meet all the requirements of the user. If you have good comments or suggestions during the trial period, you can also give us feedback in a timely manner. Our study materials will give you a benefit as Thanks, we do it all for the benefits of the user. Civil-Engineering-Technology study materials look forward to your joining in. We have full confidence to ensure that you will have an enjoyable study experience with our Civil-Engineering-Technology Certification guide, which are designed to arouse your interest and help you pass the exam more easily. You will have a better understanding after reading the following advantages.
Valid Civil-Engineering-Technology Mock Test: https://www.passsureexam.com/Civil-Engineering-Technology-pass4sure-exam-dumps.html
What's more, part of that PassSureExam Civil-Engineering-Technology dumps now are free: https://drive.google.com/open?id=1rckjn1tvsqUUikK3QDCbTfAwwyOqK08F