Users do not need to spend too much time on 93-Tall-Mass-Timber-Buildings questions torrent, only need to use their time pieces for efficient learning, the cost is about 20 to 30 hours, users can easily master the test key and difficulties of questions and answers of 93-Tall-Mass-Timber-Buildings Prep Guide, and in such a short time acquisition of accurate examination skills, better answer out of step, so as to realize high pass the qualification test, has obtained the corresponding qualification certificate.
| Section | Objectives |
|---|---|
| Special Inspection Requirements | - Inspector duties and responsibilities - Special inspection procedures for tall mass timber buildings - Inspection of connections and protective materials |
| Tall Mass Timber Building Code Provisions | - Types IV-A, IV-B and IV-C construction - Mass timber materials and construction requirements - International Building Code requirements for tall mass timber construction |
| Structural Inspection | - Connections and fastening systems - Structural loads and related code requirements - Mass timber structural elements |
| Code Compliance and Related Requirements | - Documentation and verification of compliance - Energy code requirements applicable to mass timber buildings - Sound transmission requirements |
| Construction Fire Safety | - Construction-phase fire safety requirements - Protection of mass timber during construction - International Fire Code requirements |
| Fire Protection and Fire-Resistance | - Fire-resistance requirements - Noncombustible protection and protection of mass timber elements - Fire protection systems and related provisions |
>> 93-Tall-Mass-Timber-Buildings Best Study Material <<
In order to make every customer to get the most suitable method to review 93-Tall-Mass-Timber-Buildings exam, we provide three versions of the 93-Tall-Mass-Timber-Buildings exam materials: PDF, online version, and test software. We believe that there is always a kind of method to best help your exam preparation. Each version has a free demo for you to try, and each version has the latest and most comprehensive 93-Tall-Mass-Timber-Buildings Exam Materials.
NEW QUESTION # 39
Periodic special inspection of sealants or adhesives as specified by the International Building Code Section
703.7 shall be conducted at which of the following locations?
Answer: D
Explanation:
IBC Section 703.7 requires sealant or adhesive to resist air passage at the abutting edges and intersections of mass timber building elements where those elements are required to be fire-resistance rated. Section 1705.20 then requires periodic special inspection where those prescribed sealants or adhesives are installed. Option C repeats that first required location accurately.
Option D is defective because the code requires sealing at an intersection between mass timber and another material only where both intersecting building elements are required to be fire-resistance rated. The phrase
"one or the other" materially weakens the condition. Option A is also too broad. A code-defined joint is not automatically subject to Section 703.7; fire-resistant joint systems are separately regulated by Section 715 and, where applicable, Section 1705.18.
Option B describes the exception in reverse. Sealant or adhesive need not be added under Section 703.7 where it is not a required component of the tested fire-resistance-rated assembly. When it is part of the listed or tested assembly, it must be installed accordingly, but that statement does not identify the primary location requested.
References/Topics: 2021 IBC Sections 703.7 and 1705.20; sealing of adjacent rated mass timber elements; periodic inspection.
NEW QUESTION # 40
Which of the following provisions for mass timber used for interior exit and elevator hoistway enclosures is true?
Answer: A
Explanation:
Option A correctly reflects the required noncombustible protection for protected Type IV-A mass timber.
Under IBC Section 602.4.1.2.1, the noncombustible protection applied to interior faces of Type IV-A mass timber must contribute the protection time determined by the applicable provisions of Section 722.7, but not less than 80 minutes .
The broader Type IV provisions are particularly important for interior exit and elevator hoistway enclosures.
In qualifying tall mass timber buildings with an occupied floor more than 75 feet above the lowest level of fire department access, mass timber interior exit and elevator hoistway enclosures are permitted up to the specified height limits only where protected in accordance with Section 602.4.1.2. For a two-hour, 120- minute-rated enclosure, at least 80 minutes must therefore come from the prescribed noncombustible protection.
Type IV-B likewise uses an 80-minute minimum for protected interior mass timber, so option B ' s 40-minute value is incorrect. Type IV-C has different exposure allowances and shaft-protection provisions, but option C does not state the controlling tall-building enclosure requirement tested here. Type IV-HT is not governed by the Type IV-A tall mass timber enclosure protection rule.
References/Topics: 2021 IBC Sections 602.4 and 602.4.1.2 through 602.4.1.2.1; Section 722.7.
NEW QUESTION # 41
When Type X gypsum board is used as noncombustible protection over mass timber on the building ' s exterior walls, which of the following fasteners are permitted?
Answer: A
Explanation:
Option A reproduces one of the two permitted exterior gypsum-board fastening methods in 2021 IBC Section
722.7.2.2. Type X gypsum board used as noncombustible protection on the exterior side of mass timber walls may be attached using galvanized nails of minimum 12 gage with a 7/16-inch head and sufficient length to penetrate the mass timber at least 1 inch .
The code also permits ASTM C1002 Type S, W, or G screws, but those screws must likewise penetrate the mass timber a minimum of 1 inch . Options C and D are therefore incorrect because they specify only 3/4- inch and 7/8-inch penetration, respectively. Option B is incorrect because it substitutes 16-gage nails for the minimum 12-gage requirement.
Section 722.7.2.2 additionally requires exterior Type X gypsum-board layers to be fastened 12 inches on center each way and 6 inches on center at joints or ends. Panel-edge fasteners must be located at least 1 inch and not more than 2 inches from the edge.
These fastening details are part of the conditions necessary to claim the protection contribution in Table
722.7.1(2).
References/Topics: 2021 IBC Sections 722.7.1 and 722.7.2.2; exterior Type X gypsum-board protection.
NEW QUESTION # 42
Refer to the exhibit by clicking on the EXHIBIT button above.
In the detail shown, if the connections between the glulam beam and CLT panels all require a fire-resistance rating of one (1) hour and the wood cover is designed per AWC Technical Report 10 to provide the entire 1 hour of protection, what is the minimum thickness and number of layers required for the locations shown in red?
Answer: D
Explanation:
Two layers of 5/8-inch Type X gypsum wallboard are required for the condition shown, so option D is correct. The relevant AWC TR10 connection-protection methodology distinguishes between outer gypsum layers and the base layer immediately adjacent to the connection .
For 5/8-inch Type X gypsum board, an outer layer contributes 40 minutes. However, when gypsum board is being relied upon as the complete thermal-separation protection for a connection, TR10 reduces the contribution of the final/base layer to 50 percent. Therefore, the base layer contributes 20 minutes , while the second, exterior layer contributes 40 minutes . The total is:
20 minutes + 40 minutes = 60 minutes .
That satisfies the one-hour required protection period.
This is why simply looking at the normal 40-minute contribution of one 5/8-inch Type X layer would be incorrect for this connection condition. TR10 expressly uses the reduced base-layer contribution when gypsum constitutes the connection protection. The same methodology shows that four 5/8-inch Type X layers are needed for 120 minutes: 20 + 40 + 40 + 40 = 140 minutes, satisfying two hours.
References/Topics: AWC Technical Report No. 10, Sections 4.4.2 and connection-protection examples. TR10 states that outer 5/8-inch Type X layers provide 40 minutes each while the base layer provides 20 minutes.
NEW QUESTION # 43
Which of the following is true regarding Type IV-B unprotected portions of mass timber ceilings and walls?
Answer: C
Explanation:
Type IV-B construction is fundamentally protected mass timber construction, but the 2021 IBC permits specifically limited areas of interior mass timber to remain exposed. Section 602.4.2.2.2 establishes two independent exposure limits. Unprotected portions of mass timber ceilings, including attached beams, are limited to 20 percent of the floor area of the dwelling unit or fire area. Unprotected portions of mass timber walls, including attached columns, are limited to 40 percent of that floor area . Accordingly, option C correctly states the permitted percentages.
These percentages do not operate in isolation. Exposed areas must also comply with Section 602.4.2.2.4, which establishes separation requirements between unprotected mass timber surfaces. Where both walls and ceilings are exposed within the same dwelling unit or fire area, Section 602.4.2.2.3 requires use of the mixed- unprotected-area equation rather than independently maximizing both percentages.
Option A describes neither Type IV-B nor its controlled-exposure concept. Option B incorrectly characterizes Type IV-B as requiring complete encapsulation. Option D reverses the ceiling and wall percentages.
References/Topics: 2021 IBC Sections 602.4.2.2.2, 602.4.2.2.3 and 602.4.2.2.4; Type IV-B permitted exposed mass timber.
NEW QUESTION # 44
......
These mock tests are specially built for you to assess what you have studied. These 93-Tall-Mass-Timber-Buildings Practice Tests are customizable, which means you can change the time and questions according to your needs. You can even access your previously given tests from the history, which helps you to overcome mistakes while giving the actual test next time.
93-Tall-Mass-Timber-Buildings Valid Test Vce Free: https://www.testsdumps.com/93-Tall-Mass-Timber-Buildings_real-exam-dumps.html