International Code Council M2日本語版テキスト内容 & M2科目対策

「今の生活と仕事は我慢できない。他の仕事をやってみたい。」このような考えがありますか。しかし、どのようにより良い仕事を行うことができますか。ITが好きですか。ITを通して自分の実力を証明したいのですか。IT業界に従事したいなら、IT認定試験を受験して認証資格を取得することは必要になります。あなたが今しなければならないのは、広く認識された価値があるIT認定試験を受けることです。そうすれば、新たなキャリアへの扉を開くことができます。International Code CouncilのM2認定試験というと、きっとわかっているでしょう。この資格を取得したら、新しい仕事を探す時、あなたが大きなヘルプを得ることができます。何ですか。自信を持っていないからM2試験を受けるのは無理ですか。それは問題ではないですよ。あなたはJPTestKingのM2問題集を利用することができますから。

International Code Council M2 Exam Syllabus Topics:

Section	Objectives
Heating and Cooling Systems	- Heating Appliances 1. Boilers 2. Water Heaters 3. Furnaces - Cooling Systems 1. Refrigeration Equipment 2. Cooling Appliances
Hydronic Piping and Refrigeration	- Hydronic Systems 1. Piping Installation 2. Pressure Testing - Refrigeration 1. Safety Controls 2. Refrigerant Piping
Materials and Specifications	- Approved Materials 1. Installation Standards 2. Equipment Labeling
Duct Systems	- Air Distribution 1. Duct Insulation 2. Plenums - Duct Construction 1. Materials and Installation 2. Dampers and Protection
General Administration	- Code Scope and Administration 1. Definitions 2. Permits and Inspections 3. Referenced Standards
Chimneys and Vents	- Vent Systems 1. Vent Sizing 2. Chimney Clearances - Connectors and Terminations 1. Termination Requirements 2. Vent Connectors
Ventilation and Exhaust Systems	- Ventilation 1. Mechanical Ventilation 2. Exhaust Air Systems - Commercial Kitchens 1. Grease Ducts 2. Kitchen Exhaust Hoods
Combustion Air and Fuel Supply	- Combustion Air 1. Indoor and Outdoor Air Requirements 2. Combustion Air Openings - Fuel Supply Systems 1. Fuel Oil Systems 2. Fuel Gas Piping

>> International Code Council M2日本語版テキスト内容 <<

M2科目対策、M2試験

被験者は定期的に計画を立て、自分の状況に応じて目標を設定し、研究を監視および評価することにより、学習者のプロフィールを充実させる必要があります。 M2試験の準備に役立つからです。試験に合格して関連する試験を受けるには、適切な学習プログラムを設定する必要があります。当社からM2テストガイドを購入し、それを真剣に検討すると、最短時間でM2試験に合格するのに役立つ適切な学習プランが得られると考えています。

International Code Council Commercial Mechanical Inspector 認定 M2 試験問題 (Q12-Q17):

質問 # 12
Indoor combustion air shall be provided within:

A. 1 foot of the ceiling and 1 foot of the floor.
B. 1 foot of the ceiling and 2 feet of the floor.
C. 2 feet of the ceiling and 1 foot of the floor.
D. 2 feet of the ceiling and 2 feet of the floor.

正解：A

質問 # 13
For the installation of listed fuel-burning appliances, the required clearances should be found:

A. on the approved plans and specifications for the building.
B. by using a calculation based on the Btu/h output rating of the appliance.
C. on the nameplate of the appliance.
D. in the mechanical code.

正解：C

解説：
The IMC requires fuel-burning units to be marked with the hourly rating, approved fuel type, and required clearances . That means the appliance marking/nameplate is the direct source for the required clearance information for listed fuel-burning appliances. This is why B is the correct answer.

質問 # 14
Exposed solar thermal equipment protected by motor vehicle impact may be installed at what height?

A. 18 inches above finished floor
B. Directly on finished floor
C. 6 feet above finished floor
D. 48 inches above finished floor

正解：B

解説：
The IMC states that solar thermal equipment exposed to vehicular traffic must be installed not less than 6 feet above the finished floor . It then gives an exception stating that this requirement does not apply where the equipment is protected from motor vehicle impact . Because the height requirement is removed by that exception, the best answer from the choices given is A, directly on finished floor . This is an inference from the exception language.

質問 # 15
Air mechanically exhausted from a room must be:

A. discharged into the attic.
B. discharged to the outdoors.
C. filtered.
D. recirculated.

正解：B

解説：
The IMC requires air removed by a mechanical exhaust system to be discharged outdoors to an approved location and not be readily drawn back into the building. That makes D correct. The code does not permit general exhaust air to terminate in an attic, and it does not make filtering or recirculation the default rule for mechanically exhausted air.

質問 # 16
A cooling system with a condensate disposal system:

A. shall be made of approved corrosion-resistant material and shall not decrease in size from the drain pan connection to the place of condensate disposal.
B. shall not be less than 3/4-inch PVC pipe or equivalent approved material.
C. shall have all horizontal sections of drain piping installed with a minimum of 1/4 inch per foot slope.
D. shall be made of an approved pipe and be at least 1/2-inch in diameter.

正解：A

解説：
The ICC mechanical code requires condensate disposal components to be of approved corrosion-resistant material , and the drain line shall not decrease in size from the drain pan connection to the place of disposal.
The code minimum size is 3/4 inch , so the 1/2-inch statement is incorrect, and the code is not limited to PVC only. Also, the slope requirement for horizontal drain piping is not less than 1/8 inch per foot , not 1/4 inch per foot. That makes Option A the only fully correct statement.

質問 # 17
......

試験の知識が豊富な専門家によってコンパイルされたM2試験トレントをすべての受験者に提供し、M2学習教材のコンパイルの経験が豊富です。最新バージョンを入手したら、できるだけ早くメールボックスに送信します。 M2試験問題では、学生が練習に20〜30時間を費やすだけでM2試験に合格する自信が持てるので、一部の労働者にとっては非常に便利です。 M2試験に合格して目標を達成するための最良のツールでなければなりません。

M2科目対策: https://www.jptestking.com/M2-exam.html