그리고 Fast2test NSE4_FGT_AD-7.6 시험 문제집의 전체 버전을 클라우드 저장소에서 다운로드할 수 있습니다: https://drive.google.com/open?id=19gOwqxV7-YN1nVKwilIGAgTb4wPke349
Fast2test의 Fortinet인증 NSE4_FGT_AD-7.6덤프를 구매하여 공부한지 일주일만에 바로 시험을 보았는데 고득점으로 시험을 패스했습니다.이는Fast2test의 Fortinet인증 NSE4_FGT_AD-7.6덤프를 구매한 분이 전해온 희소식입니다. 다른 자료 필요없이 단지 저희Fortinet인증 NSE4_FGT_AD-7.6덤프로 이렇게 어려운 시험을 일주일만에 패스하고 자격증을 취득할수 있습니다.덤프가격도 다른 사이트보다 만만하여 부담없이 덤프마련이 가능합니다.구매전 무료샘플을 다운받아 보시면 믿음을 느낄것입니다.
| Section | Objectives |
|---|---|
| Topic 1: Routing and SD-WAN | - Static and dynamic routing
|
| Topic 2: Firewall Policies and Authentication | - User authentication
|
| Topic 3: FortiGate Deployment and System Configuration | - Initial setup and configuration
|
| Topic 4: Security Profiles and Content Inspection | - Antivirus and intrusion prevention
|
| Topic 5: Monitoring and Troubleshooting | - Logging and reporting
|
| Topic 6: Network Security Concepts and Architecture | - Fortinet Security Fabric Overview
|
| Topic 7: VPN and Secure Connectivity | - IPsec VPN
|
멋진 IT전문가로 거듭나는 것이 꿈이라구요? 국제적으로 승인받는 IT인증시험에 도전하여 자격증을 취득해보세요. IT전문가로 되는 꿈에 더 가까이 갈수 있습니다. Fortinet인증 NSE4_FGT_AD-7.6시험이 어렵다고 알려져있는건 사실입니다. 하지만Fast2test의Fortinet인증 NSE4_FGT_AD-7.6덤프로 시험준비공부를 하시면 어려운 시험도 간단하게 패스할수 있는것도 부정할수 없는 사실입니다. Fast2test의Fortinet인증 NSE4_FGT_AD-7.6덤프는 실제시험문제의 출제방형을 철저하게 연구해낸 말 그대로 시험대비공부자료입니다. 덤프에 있는 내용만 마스터하시면 시험패스는 물론 멋진 IT전문가로 거듭날수 있습니다.
질문 # 68
Refer to the exhibit.
A routing table is shown
An administrator wants to create a new static route so the traffic to the subnet 172.20.1.0/24 is routed through port2 only. What are the two criteria that the administrator can use to achieve this objective? (Choose two.)
정답：A,C
설명：
From the routing table in the exhibit, there is already a static route for 172.20.1.0/24 pointing out port3 with:
Distance = 9
Priority = 2
Type = Static
In FortiOS, route selection prefers (in order) the route with the lowest administrative distance to a destination. Therefore, to make traffic to 172.20.1.0/24 go through port2 only, the administrator must ensure the port2 static route is more preferred than the existing port3 route.
Why C is correct
C . The existing static route through port3 must have the distance set to 11.
If the existing port3 route distance is increased to 11, then a new port2 route with distance 9 will be preferred (9 < 11). This makes the port3 route a backup route instead of the active one.
Why D is correct
D . The new static route must have the distance set to 9
Setting the new port2 route distance to 9 (and increasing the port3 route to 11 as in option C) ensures FortiGate selects the port2 route as the best route for 172.20.1.0/24.
Why A and B are not correct
A (priority 3): By itself it does not guarantee selection over the existing route, and FortiOS route choice is driven primarily by distance.
B (metric 1): Metric is not the primary selector for static route preference compared to administrative distance in this scenario.
So the two criteria that achieve the objective are:
Make the existing port3 route less preferred by increasing its distance (C) Ensure the new port2 route uses the preferred distance (D)
질문 # 69
Refer to the exhibit.
Why did the FortiGate device drop the packet?
정답：B
설명：
"FortiGate looks for the matching firewall policy from top-to-bottom and, if a match is found, the traffic is processed based on the firewall policy. If no match is found, the traffic is dropped by the default implicit deny firewall policy. " Technical Deep Dive:
The debug flow output clearly points to the implicit deny :
* ret-no-match
* policy-0 is matched, act-drop
* Denied by forward policy check (policy 0)
On FortiGate, policy 0 is the internal representation of the default implicit deny firewall policy . That means the packet did not match any user-defined forward firewall policy, so FortiGate dropped it automatically.
Why the other options are wrong:
* B is wrong because an RPF failure would show a reverse-path-related drop reason, not Denied by forward policy check (policy 0).
* C is wrong because the trace does not show a matched explicit policy ID with deny action; it shows policy 0 , which is the implicit rule.
* D is wrong because the trace actually shows a route lookup result: find a route: ... gw-0.0.0.0 via port2.
So this is not a next-hop reachability failure.
In packet-flow troubleshooting, this pattern is one of the most important to recognize. If you see policy 0 in FortiGate debug flow, the first things to verify are:
diagnose debug flow filter addr < src_or_dst_ip >
diagnose debug flow show function-name enable
diagnose debug enable
Then review whether a firewall policy exists with the correct incoming interface, outgoing interface, source, destination, schedule, and service . If any one of those does not match, FortiGate falls through to policy 0 and drops the session.
질문 # 70
Refer to the exhibits. An administrator has observed the performance status outputs on an HA cluster for 55 seconds.
Which FortiGate is the primary?
정답：D
설명：
The HA configuration shows that override is disabled (set override disable), but despite this, HQ- NGFW-1 has the higher priority (200) and is acting as the primary, as indicated by its higher resource usage and uptime. Override allows the device with higher priority to take over as primary, so HQ- NGFW-1 is the primary device.
질문 # 71
Refer to the exhibits.
You have implemented the application sensor and the corresponding firewall policy as shown in the exhibits.
Which two factors can you observe from these configurations? (Choose two.)
정답：A,B
설명：
From the exhibits:
The Application Control sensor has these key settings:
Application and Filter Overrides
Priority 1: Excessive-Bandwidth (Type: Filter) with Action Block
Priority 2: Google (Type: Filter) with Action Monitor
Category actions shown include Social Media set to Block (this category includes Facebook).
The firewall policy is using:
Flow-based inspection
Application control enabled (profile: default)
Deep inspection enabled (helps identify applications inside HTTPS)
Logging enabled
FortiOS applies Application Control as follows (top-down within the Application Control profile):
Overrides are evaluated by priority (highest priority first).
The first matching override determines the action (block/monitor/allow) for that traffic.
Category-based actions apply to applications that fall into those categories unless an override matches first.
Why A is correct
A . YouTube access is blocked based on Excessive-Bandwidth Application and Filter override settings.
The profile explicitly blocks the Excessive-Bandwidth behavior filter at the highest override priority.
When YouTube traffic is detected as matching the Excessive-Bandwidth behavior, FortiGate will apply the Block action due to the override.
Because this is a priority override, it is enforced before lower-priority entries.
Why B is correct
B . Facebook access is blocked based on the category filter settings.
The Application Sensor shows Social Media configured with a Block action.
Facebook is categorized under Social Media, so it will be blocked when matched by Application Control.
Why C is not correct
C . Facebook access is allowed but you cannot play Facebook videos...
Since the Social Media category is set to Block, Facebook would be blocked at the category level (not merely video playback).
Why D is not correct
D . YouTube search is allowed based on the Google override...
The Google override action is Monitor, not Allow.
"Monitor" logs/detects but does not override a block condition to "allow" traffic.
Also, YouTube traffic is not guaranteed to be treated as "Google" in a way that would permit it, and any matching block condition (such as Excessive-Bandwidth) would still take precedence.
질문 # 72
Which three pieces of information does FortiGate use to identify the hostname of the SSL server when SSL certificate inspection is enabled? (Choose three.)
정답：A,B,C
설명：
When SSL certificate inspection is enabled on a FortiGate device, the system uses the following three pieces of information to identify the hostname of the SSL server:
Server Name Indication (SNI) extension in the client hello message (B): The SNI is an extension in the client hello message of the SSL/TLS protocol. It indicates the hostname the client is attempting to connect to. This allows FortiGate to identify the server's hostname during the SSL handshake.
Subject Alternative Name (SAN) field in the server certificate (C): The SAN field in the server certificate lists additional hostnames or IP addresses that the certificate is valid for. FortiGate inspects this field to confirm the identity of the server.
Subject field in the server certificate (D): The Subject field contains the primary hostname or domain name for which the certificate was issued. FortiGate uses this information to match and validate the server's identity during SSL certificate inspection.
질문 # 73
......
Fortinet인증 NSE4_FGT_AD-7.6시험을 패스하여 자격증을 취득하는게 꿈이라구요? Fast2test에서 고객님의Fortinet인증 NSE4_FGT_AD-7.6시험패스꿈을 이루어지게 지켜드립니다. Fast2test의 Fortinet인증 NSE4_FGT_AD-7.6덤프는 가장 최신시험에 대비하여 만들어진 공부자료로서 시험패스는 한방에 끝내줍니다.
NSE4_FGT_AD-7.6최신 업데이트버전 인증시험자료: https://kr.fast2test.com/NSE4_FGT_AD-7.6-premium-file.html
참고: Fast2test에서 Google Drive로 공유하는 무료 2026 Fortinet NSE4_FGT_AD-7.6 시험 문제집이 있습니다: https://drive.google.com/open?id=19gOwqxV7-YN1nVKwilIGAgTb4wPke349