ValidBraindumps NSEI_OTS_AR-7.6 practice material can be accessed instantly after purchase, so you won't have to face any excessive issues for preparation of your desired Fortinet NSEI_OTS_AR-7.6 certification exam. The Fortinet NSEI_OTS_AR-7.6 Exam Dumps of ValidBraindumps has been made after seeking advice from many professionals. Our objective is to provide you with the best learning material to clear the Fortinet NSE I - OT Security 7.6 Architect (NSEI_OTS_AR-7.6) exam.
| Section | Objectives |
|---|---|
| Asset Management | - Use Fortinet Security Fabric for an OT network - Implement device detection on FortiGate and FortiNAC - Explain OT standards and Fortinet compliance |
| Monitoring and Risk Assessment | - Create FortiAnalyzer event handlers - Analyze security reports from FortiAnalyzer - Perform risk assessment and management |
| Network Access Control | - Configure network access authentication - Explain OT Ethernet concepts - Configure network segmentation schemas |
| Network Security | - Configure security inspections for industrial protocols - Configure automation - Configure virtual patching |
>> Reliable NSEI_OTS_AR-7.6 Learning Materials <<
Our Fortinet NSE I - OT Security 7.6 Architect test torrent boost 99% passing rate and high hit rate so you can have a high probability to pass the exam. Our NSEI_OTS_AR-7.6 study torrent is compiled by experts and approved by the experienced professionals and the questions and answers are chosen elaborately according to the syllabus and the latest development conditions in the theory and the practice and based on the real exam. If you buy our Fortinet NSE I - OT Security 7.6 Architect test torrent you only need 1-2 hours to learn and prepare the exam and focus your main attention on your most important thing.
NEW QUESTION # 20
Refer to the exhibit.
A partial OT network is shown. You want to configure an automated alert sent by FortiAnalyzer when an attack occurs on a FortiGate device. Which two configurations must you implement? (Choose two answers)
Answer: A,B
Explanation:
The correct answers are A and D . The study guide provides a direct use case called Attack Detection and Automated Alert . It states: "A downstream FortiGate detects an attack and sends logs to FortiAnalyzer. FortiAnalyzer parses the logs and notifies the root FortiGate. The root FortiGate triggers the action, which in this case, is a notification to the administrator." The same slide also explicitly shows "Stitches configured on root FortiGate." This confirms that to send the automated alert, you must configure the automation stitch on the root FortiGate .
The second required configuration is an event handler on FortiAnalyzer . The guide explains that "Event handlers generate events" and that "FortiAnalyzer uses event handlers to filter all incoming logs. If logs match the conditions configured in an event handler, FortiAnalyzer generates an event." Since FortiAnalyzer must detect the attack from the received logs before notifying the root FortiGate, an event handler is required on FortiAnalyzer.
Option B is incorrect because the study guide does not identify a LOCALHOST task as the required configuration for this attack-alert flow. Option C is also incorrect because the question asks what must be configured to enable the automated alert workflow . An IPS profile may detect some attacks, but the required automation path in the study guide is specifically event handler on FortiAnalyzer + stitch on the root FortiGate .
NEW QUESTION # 21
Refer to the exhibit.
Why is the OT View tab not available in the Asset Identity Center section of the FortiGate-1 device? (Choose one answer)
Answer: B
Explanation:
The correct answer is A . The study guide states that "The OT view is not available by default. You must enable it in the Feature Visibility section of the GUI or using the CLI command shown on this slide" and shows config system settings # set gui-ot enable . It also says that "After you enable the feature, the Asset Identity Center contains an Asset Identity List tab and an OT View tab." This directly explains why the OT View tab is missing: the feature that enables the Purdue-style OT display has not been enabled yet.
The OT View is the view that displays devices in a Purdue diagram , and the Asset Identity List also shows the current Purdue level for each device. Because the answer options do not explicitly say enable OT View in Feature Visibility , option A is the intended match, since it refers to enabling the Purdue-related OT display feature. Option B is incorrect because device detection affects visibility of devices, not whether the OT View tab exists. Option C is not supported by the study guide, and option D is also not given as the requirement for showing the OT View tab.
NEW QUESTION # 22
Refer to the exhibit.
A partial Application Sensor profile is shown. When you apply this profile in a firewall policy, which two statements are correct? (Choose two answers)
Answer: B,C
Explanation:
The correct answers are A and C .
Option C is correct because the profile clearly contains the Operational Technology category and specific OT application signatures such as Modbus and IEC.60870.5.104 . The study guide says "You can use application control signatures to detect OT protocols" and "You can filter to a specific OT protocol." That means OT application signatures are active in this sensor profile.
Option A is correct because the guide explains that application control works at different levels: "Detection of protocol (one detection per session)" and "Message level (one detection per protocol message)." It also says you can use application signatures for "granular message type identification." In the exhibit, IEC.
60870.5.104.Control.Functions is explicitly configured, which is a granular IEC message/control-level signature rather than only a protocol-level match. That means logging and control can occur at the IEC command level.
Option B is not correct because the profile shows Modbus configured at the parent protocol level as Monitor
, while the guide states that the "parent signature takes precedence over the child signature." Since protocol-level detection is one detection per session , that does not mean FortiGate will necessarily log each Modbus command individually.
Option D is incorrect because even though the broader Operational Technology category is set to block, the profile includes specific application and filter overrides for Modbus and IEC 104 behavior. So the resulting effect is not simply that all OT protocols are blocked .
NEW QUESTION # 23
In the Purdue model, at which level are physical assets like the Industrial Internet of Things (IIoT) placed?
(Choose one answer)
Answer: B
Explanation:
According to the OT Security 7.6 Architect study guide regarding the Purdue Model :
* Asset Location : The study guide states that " All critical physical assets are located on the plant floor and equipped with IIoT sensors. "
* Level Classification : The " plant floor " is further defined as the " control area zone, " which consists of Levels 0, 1, and 2 .
* Hierarchy : The " Operations & Control " zone is identified as Level 3 and Level 3.5 .
* Direct Answer : In the " Introduction " lesson ' s Knowledge Check , the specific question " In the Purdue model, at which level are IIoTs placed? " is provided with the verified answer: Below Level 3.5 .
NEW QUESTION # 24
Refer to the exhibit. A partial OT network is shown. You must improve the security of this OT network and implement internal segmentation between network 1 and network 2. How can you achieve the segmentation?
(Choose one answer)
Answer: D
Explanation:
The correct answer is D. You can configure forward domain IDs for each network . The study guide explains that in FortiGate transparent mode, "all interfaces belong to the same broadcast domain, even interfaces with different VLAN IDs" and then states that you should "use this command to subdivide into multiple broadcast domains" with set forward-domain < domain_ID > . It further explains that
"interfaces with the same domain ID belong to the same broadcast domain" and "traffic arriving on one interface is broadcast only to interfaces in the same forward domain ID." This is exactly the mechanism used to separate one internal network from another and improve segmentation.
The other options do not match this requirement. Universal ZTNA is described as controlling user access to applications , not segmenting two internal OT networks. An explicit software switch is for controlling intra- switch or intra-VLAN traffic inside the same software switch broadcast domain, which is more aligned with microsegmentation than separating two routed internal networks. One traffic VDOM does not create segmentation by itself; segmentation with VDOMs requires multiple VDOMs, not one. Therefore, the best choice for segmenting network 1 and network 2 in this scenario is to assign separate forward domain IDs .
NEW QUESTION # 25
......
Getting NSEI_OTS_AR-7.6 exam certified is not easy. To pass the exam, one must put in a tremendous amount of effort, resolve, and dedication. One of the most dependable sites, ValidBraindumps provides students with accurate, dependable, and simple Fortinet NSEI_OTS_AR-7.6 Dumps to assure their success on the first attempt. For those looking to pass the NSEI_OTS_AR-7.6 exam certificate on their first attempt, ValidBraindumps provides the full package, which includes all exam dumps that follow the syllabus.
Authorized NSEI_OTS_AR-7.6 Pdf: https://www.validbraindumps.com/NSEI_OTS_AR-7.6-exam-prep.html