No matter how busy you are, you must reserve some time to study. As we all know, knowledge is wealth. If you have a strong competitiveness in the society, no one can ignore you. Then here comes the good news that our NSEI_OTS_AR-7.6 practice materials are suitable for you. For the advantage of our NSEI_OTS_AR-7.6 Exam Questions is high-efficient. No only we can give the latest and most accurate knowledge on the subject, but also we can help you pass the exam and get the NSEI_OTS_AR-7.6 certification in the least time.
| Section | Objectives |
|---|---|
| Monitoring and Risk Assessment | - Perform risk assessment and management - Analyze security reports from FortiAnalyzer - Create FortiAnalyzer event handlers |
| Network Security | - Configure automation - Configure security inspections for industrial protocols - Configure virtual patching |
| Network Access Control | - Configure network access authentication - Explain OT Ethernet concepts - Configure network segmentation schemas |
| Asset Management | - Implement device detection on FortiGate and FortiNAC - Use Fortinet Security Fabric for an OT network - Explain OT standards and Fortinet compliance |
>> New NSEI_OTS_AR-7.6 Exam Practice <<
After undergoing a drastic change over these years, our NSEI_OTS_AR-7.6 actual exam have been doing perfect job in coping with the exam. Up to now our NSEI_OTS_AR-7.6 practice materials account for 60 percent of market share in this line for their efficiency and accuracy when dealing with the exam. With the best reputation in the market our NSEI_OTS_AR-7.6 Training Materials can help you ward off all unnecessary and useless materials and spend all your limited time on practicing most helpful questions.
NEW QUESTION # 46
Refer to the exhibit.
A partial Application Sensor profile is shown. When you apply this profile in a firewall policy, which two statements are correct? (Choose two answers)
Answer: A,B
Explanation:
The correct answers are A and C .
Option C is correct because the profile clearly contains the Operational Technology category and specific OT application signatures such as Modbus and IEC.60870.5.104 . The study guide says "You can use application control signatures to detect OT protocols" and "You can filter to a specific OT protocol." That means OT application signatures are active in this sensor profile.
Option A is correct because the guide explains that application control works at different levels: "Detection of protocol (one detection per session)" and "Message level (one detection per protocol message)." It also says you can use application signatures for "granular message type identification." In the exhibit, IEC.
60870.5.104.Control.Functions is explicitly configured, which is a granular IEC message/control-level signature rather than only a protocol-level match. That means logging and control can occur at the IEC command level.
Option B is not correct because the profile shows Modbus configured at the parent protocol level as Monitor
, while the guide states that the "parent signature takes precedence over the child signature." Since protocol-level detection is one detection per session , that does not mean FortiGate will necessarily log each Modbus command individually.
Option D is incorrect because even though the broader Operational Technology category is set to block, the profile includes specific application and filter overrides for Modbus and IEC 104 behavior. So the resulting effect is not simply that all OT protocols are blocked .
NEW QUESTION # 47
Which industrial protocol does not support VLANs? (Choose one answer)
Answer: A
Explanation:
The correct answer is C. EtherCAT .
The study guide states that for industrial Ethernet protocols, "such as Ethernet/IP and Modbus/TCP, you can use VLANs to segment your physical LAN into multiple logical LANs." This directly confirms that Ethernet/IP and Modbus/TCP support VLAN-based segmentation in the OT context.
By contrast, the guide explains that "EtherCAT skips layers 3 to 6 to deliver real-time communication" and describes it as an "Open-Software Modified-Ethernet" approach. Because it does not operate like the standard Ethernet/IP model used for normal VLAN-based segmentation, EtherCAT is the protocol identified here as not supporting VLANs in the way Ethernet/IP and Modbus/TCP do.
So, based on the study guide comparison, the verified answer is EtherCAT .
NEW QUESTION # 48
Refer to the exhibit.
A partial OT network is shown. You have configured the FortiGate device with VLANs to segment the OT network. The supervisor now wants to connect to the PLC from the Engineering Workstation. How can you allow access from the Engineering Workstation to the PLC? (Choose one answer)
Answer: C
Explanation:
The correct answer is D. You must configure a layer 3 switch .
The study guide explains that "Layer 2 devices can add or remove tags" but "cannot modify them." It then states that "A layer 3 device, such as a router or FortiGate, can modify the VLAN tag before routing the packet. This allows them to route traffic between VLANs." It also explicitly describes
"Router on a Stick" as "a way to allow routing between VLANs." Since the exhibit shows a layer-2 switch and the Engineering Workstation and PLC are placed in different VLANs, inter-VLAN communication requires layer-3 routing.
The other options do not solve this requirement. intra-switch-policy explicit/implicit applies to a software switch , where member interfaces are in the same broadcast domain and same subnet, not to routing between separate VLANs. forward domain IDs are used in transparent mode to confine broadcasts to specific broadcast domains; they do not provide inter-VLAN access. Therefore, to let the Engineering Workstation in one VLAN reach the PLC in another VLAN, you need a layer 3 routing function , which matches option D .
NEW QUESTION # 49
Refer to the exhibit.
A partial OT network is shown. You have configured the FortiGate device with VLANs to segment the OT network. The supervisor now wants to connect to the PLC from the Engineering Workstation. How can you allow access from the Engineering Workstation to the PLC? (Choose one answer)
Answer: C
Explanation:
The correct answer is D. You must configure a layer 3 switch .
The study guide explains that "Layer 2 devices can add or remove tags" but "cannot modify them." It then states that "A layer 3 device, such as a router or FortiGate, can modify the VLAN tag before routing the packet. This allows them to route traffic between VLANs." It also explicitly describes
"Router on a Stick" as "a way to allow routing between VLANs." Since the exhibit shows a layer-2 switch and the Engineering Workstation and PLC are placed in different VLANs, inter-VLAN communication requires layer-3 routing.
The other options do not solve this requirement. intra-switch-policy explicit/implicit applies to a software switch , where member interfaces are in the same broadcast domain and same subnet, not to routing between separate VLANs. forward domain IDs are used in transparent mode to confine broadcasts to specific broadcast domains; they do not provide inter-VLAN access. Therefore, to let the Engineering Workstation in one VLAN reach the PLC in another VLAN, you need a layer 3 routing function , which matches option D .
NEW QUESTION # 50
Refer to the exhibit.
A FortiAnalyzer report is shown.
You must extract relevant information provided by the report regarding your OT network.
Which two statements are correct? (Choose two.)
Answer: A,B
Explanation:
The correct answers are B and C . The exhibit ' s Top Threat section identifies the IPS threats as Blocked , directly confirming that the attacks were prevented rather than merely detected. The OT Traffic table also shows destination port 502 . Modbus/TCP conventionally operates on TCP port 502, and the OT Security 7.6 study guide identifies Modbus as an industrial protocol supported and inspected by Fortinet OT security controls. The report does not cover only one day; its displayed timeline spans multiple dates, from approximately October 30 through November 3. Option D is also inconsistent with the report because the visible OT destination addresses are associated with the 192.168.x.x networks rather than 10.1.5.1.
FortiAnalyzer reports summarize logged information into charts and tables specifically to expose traffic patterns, threats, and OT activity such as this.
NEW QUESTION # 51
......
It is time for you to plan your life carefully. After all, you have to make money by yourself. If you want to find a desirable job, you must rely on your ability to get the job. Now, our NSEI_OTS_AR-7.6 training materials will help you master the popular skills in the office. With our NSEI_OTS_AR-7.6 Exam Braindumps, you can not only learn the specialized knowledge of this subject to solve the problems on the work, but also you can get the NSEI_OTS_AR-7.6 certification to compete for a higher position.
NSEI_OTS_AR-7.6 Exam Training: https://www.itexamreview.com/NSEI_OTS_AR-7.6-exam-dumps.html