Almost everyone is trying to get the Fortinet NSEI_OTS_AR-7.6 certification to update their CV or get the desired job. Every student faces just one problem and that is not finding updated study material. Applicants are always confused about where to buy real Fortinet NSEI_OTS_AR-7.6 Dumps Questions and prepare for the Fortinet NSE I - OT Security 7.6 Architect (NSEI_OTS_AR-7.6) exam in less time. Nowadays everyone is interested in getting the Fortinet NSE I - OT Security 7.6 Architect (NSEI_OTS_AR-7.6) certificate because it has multiple benefits for Fortinet career.
| Section | Objectives |
|---|---|
| Topic 1: Asset Management | - Use Fortinet Security Fabric for an OT network - Implement device detection on FortiGate and FortiNAC - Explain OT standards and Fortinet compliance |
| Topic 2: Monitoring and Risk Assessment | - Analyze security reports from FortiAnalyzer - Create FortiAnalyzer event handlers - Perform risk assessment and management |
| Topic 3: Network Security | - Configure automation - Configure security inspections for industrial protocols - Configure virtual patching |
| Topic 4: Network Access Control | - Configure network access authentication - Configure network segmentation schemas - Explain OT Ethernet concepts |
>> NSEI_OTS_AR-7.6 Vce File <<
As an old saying goes: Practice makes perfect. Facts prove that learning through practice is more beneficial for you to learn and test at the same time as well as find self-ability shortage in NSEI_OTS_AR-7.6 test prep. The PC test engine of our NSEI_OTS_AR-7.6 exam torrent is designed for such kind of condition, when the system of the NSEI_OTS_AR-7.6 Exam Torrent has renovation of production techniques by actually simulating the test environment. Until then, you will have more practical experience and get improvement rapidly through our NSEI_OTS_AR-7.6 quiz guide.
NEW QUESTION # 16
Refer to the exhibit.
A basic event handler is shown. You have enabled Automation Stitch to automate the handling of an alert.
Which two steps must you take to use this automation stitch? (Choose two answers)
Answer: B,C
Explanation:
The correct answers are C and D .
Option D is correct because the study guide states that the configuration of an event handler can include
"Rules" and explains that "Rules are granular conditions" and "Event handlers can have one or more rules." It further states that "FortiAnalyzer uses event handlers to filter all incoming logs" and "If logs match the conditions configured in an event handler, FortiAnalyzer generates an event." Therefore, to use the automation stitch, you must define the rules on FortiAnalyzer so the event handler can actually generate the event that starts the automation flow.
Option C is also correct. The study guide explains that "When a handler generates an event with the automation stitch option enabled, FortiAnalyzer sends a notification" to the FortiGate side, and in the attack-detection example it says "FortiAnalyzer parses the logs and notifies the root FortiGate" and then
"The root FortiGate triggers the action." It also explicitly shows "Stitches configured on root FortiGate." This means the FortiGate must have the corresponding automation trigger configured for the FortiAnalyzer event handler notification.
Option A is incorrect because the study guide does not describe configuring an Action on FortiAnalyzer as the required step for this FortiAnalyzer-to-FortiGate automation-stitch flow. Option B is also incorrect because playbooks are a different FortiAnalyzer automation mechanism; the question specifically refers to using the Automation Stitch option in the event handler.
NEW QUESTION # 17
Refer to the exhibit.
A partial Application Sensor profile is shown. When you apply this profile in a firewall policy, which two statements are correct? (Choose two answers)
Answer: C,D
Explanation:
The correct answers are A and C .
Option C is correct because the profile clearly contains the Operational Technology category and specific OT application signatures such as Modbus and IEC.60870.5.104 . The study guide says "You can use application control signatures to detect OT protocols" and "You can filter to a specific OT protocol." That means OT application signatures are active in this sensor profile.
Option A is correct because the guide explains that application control works at different levels: "Detection of protocol (one detection per session)" and "Message level (one detection per protocol message)." It also says you can use application signatures for "granular message type identification." In the exhibit, IEC.
60870.5.104.Control.Functions is explicitly configured, which is a granular IEC message/control-level signature rather than only a protocol-level match. That means logging and control can occur at the IEC command level.
Option B is not correct because the profile shows Modbus configured at the parent protocol level as Monitor
, while the guide states that the "parent signature takes precedence over the child signature." Since protocol-level detection is one detection per session , that does not mean FortiGate will necessarily log each Modbus command individually.
Option D is incorrect because even though the broader Operational Technology category is set to block, the profile includes specific application and filter overrides for Modbus and IEC 104 behavior. So the resulting effect is not simply that all OT protocols are blocked .
NEW QUESTION # 18
Refer to the exhibit.
A partial OT network is shown.
PLC-1 has a known critical vulnerability, but you cannot update it.
What must you configure to protect PLC-1?
Answer: B
Explanation:
The correct answer is C . This scenario is the precise use case for virtual patching . The OT Security 7.6 study guide states that virtual patching protects OT devices that have not yet been updated against vulnerability exploits . FortiGate identifies the vulnerable asset, queries FortiGuard for device-specific vulnerabilities and mitigation rules, receives applicable OT virtual-patching signatures, and maps those rules to the device. When traffic associated with the vulnerable asset reaches FortiGate, the firewall policy containing the virtual-patching profile applies the protection. In the topology, FortiGate_Level2 is the enforcement point immediately protecting PLC-1 and the control-network assets. IPS at Level 5 provides broader perimeter protection, but it is not the device-specific compensating control requested here.
Application Control primarily regulates industrial protocols and commands. Therefore, Virtual patching on FortiGate_Level2 is required.
NEW QUESTION # 19
Refer to the exhibit.
A partial OT network is shown. You have encountered many disconnections in the links and want to improve the availability of this network. Which action can you perform? (Choose one answer)
Answer: A
Explanation:
The correct answer is C. You can implement parallel redundancy protocol . The study guide explains that media redundancy involves creating a backup path that can be used when part of the network fails and specifically states that "Parallel Redundancy Protocol (PRP) can be used for a star topology." Since the problem described is many disconnections in the links , the issue is link availability, which is a media redundancy problem rather than a firewall virtualization or policy separation problem. PRP is designed to provide a backup communication path with low recovery time when links fail.
The other options do not fit this scenario as well. HA clusters are described in the guide as a solution for network node redundancy , where a backup firewall or switch takes over when the primary device fails. SD- WAN is recommended for remote site access across multiple WAN links, not for the local floor links shown in this topology. VDOMs provide logical segmentation, not link redundancy or higher link availability.
Because the question is specifically about repeated link disconnections , the best action is to implement PRP .
NEW QUESTION # 20
Refer to the exhibit.
Based on the information provided on the partial Event Monitor page shown in the exhibit, how was the attack detected? (Choose one answer)
Answer: D
Explanation:
The correct answer is D. Automatically by an event handler . The study guide explicitly states that "Event handlers generate events on FortiAnalyzer" and "FortiAnalyzer uses event handlers to filter all incoming logs. If the logs received match the conditions set in the event handlers, FortiAnalyzer generates an event." It also says "You can view all generated events on the Event Monitor page." This directly matches the exhibit, which is showing entries on the Event Monitor page. Therefore, the attack shown there was detected automatically through an event handler .
The guide also explains the detection flow: "FortiAnalyzer receives logs," "FortiAnalyzer parses logs," and "FortiAnalyzer generates an event if a rule is matched in an event handler." In addition, the Event Monitor view includes the Handler column, which identifies the event handler that generated the event. That is why the attack is not considered manually detected, and it is not primarily detected by a playbook or stitch.
Playbooks and stitches are used for subsequent automation actions, but the event appearing in Event Monitor is created by the event handler mechanism.
NEW QUESTION # 21
......
Every Fortinet aspirant wants to pass the Fortinet NSEI_OTS_AR-7.6 exam to achieve high-paying jobs and promotions. The biggest issue NSEI_OTS_AR-7.6 exam applicants face is that they don't find credible platforms to buy real NSEI_OTS_AR-7.6 exam dumps. When candidates don't locate actual Fortinet NSE I - OT Security 7.6 Architect (NSEI_OTS_AR-7.6) exam questions they prepare from outdated material and ultimately lose resources. If you are also facing the same problem then you are at the trusted spot.
Test NSEI_OTS_AR-7.6 Duration: https://www.lead1pass.com/Fortinet/NSEI_OTS_AR-7.6-practice-exam-dumps.html