Exam H35-831 Reviews - H35-831 Latest Examprep

You can save a lot of time for collecting real-time information if you choose our H35-831 study guide. Because our professionals have done all of these collections for you and they are more specialized in the field. So the keypoints are all contained in the H35-831 Exam Questions. Besides, in order to ensure that you can see the updated H35-831 practice prep as soon as possible, our system will send the updated information to your email address as soon as possible.

Huawei H35-831 Exam Syllabus Topics:

SectionWeightObjectives
Topic 1: BGP Advanced Technologies20%- Carrier-Grade BGP
  • 1. Routing Policy Control
  • 2. BGP Confederations
  • 3. BGP Convergence Optimization
  • 4. Route Reflector Design
Topic 2: IPv6 Technologies8%- IPv6 Deployment
  • 1. IPv4/IPv6 Transition Technologies
  • 2. IPv6 Routing
Topic 3: Network Service Technologies10%- Carrier Services
  • 1. EVPN
  • 2. L3VPN
  • 3. VPN Interworking
Topic 4: Network Reliability and Protection7%- High Availability Design
  • 1. Fast Reroute
  • 2. Protection Mechanisms
  • 3. BFD
Topic 5: Network Automation and SDN5%- Automation Technologies
  • 1. NETCONF and YANG
  • 2. Network Orchestration
  • 3. Intent-Based Networking
Topic 6: IGP Advanced Technologies15%- OSPF and IS-IS Advanced Features
  • 1. Multi-Topology Routing
  • 2. Traffic Engineering Extensions
  • 3. Route Convergence Optimization
Topic 7: Carrier IP Network Architecture10%- Carrier Network Evolution
  • 1. Carrier Network Architecture Design
  • 2. IP Network Development Trends
Topic 8: MPLS and Segment Routing20%- Carrier Transport Technologies
  • 1. SR Policy
  • 2. Segment Routing SR-MPLS
  • 3. MPLS Fundamentals
  • 4. MPLS Traffic Engineering
Topic 9: Network Operation and Maintenance5%- Monitoring and Troubleshooting
  • 1. Fault Diagnosis
  • 2. Service Assurance
  • 3. Performance Monitoring

>> Exam H35-831 Reviews <<

High-quality Exam H35-831 Reviews offer you accurate Latest Examprep | HCIE-Datacom-Carrier (Written) V1.0

Many users report to us that they are very fond of writing their own notes while they are learning. This will enhance their memory and make it easier to review. Our H35-831 exam questions have created a PDF version of the H35-831 practice material to meet the needs of this group of users. You can print the PDF version of the H35-831 learning guide so that you can carry it with you. As long as you have time, you can take it out to read and write your own experience.

Huawei HCIE-Datacom-Carrier (Written) V1.0 Sample Questions (Q30-Q35):

NEW QUESTION # 30
iFIT is an in-band flow-measurement technology that delivers highly precise performance measurements based on real traffic. Which functions can it provide when used with telemetry, a second-level data-collection technology, and NCE, an integrated management and control platform?
Select all that apply.

Answer: A,B,D

Explanation:
Exact Extract - Huawei Training Material (Automatic SDN Network O & M, p.52):
"iFIT is a performance detection method for in-service traffic detection. It provides high-precision real-time traffic detection and works with the Telemetry second-level data collection to implement real-time visualization of network quality, proactive monitoring, and quick fault demarcation and locating." Huawei Reference Verification:
Huawei's Automatic SDN O & M module characterizes iFIT as in-service flow performance detection using high-precision real-traffic measurement and second-level telemetry. It specifically lists real-time visualization of network quality, proactive monitoring, and quick fault demarcation and location. iFIT-enabled forwarding hardware identifies measured flows, counts packets and records time information to calculate delay and loss.
iMaster NCE-IP correlates these records across network nodes to present service-level performance and identify the faulty section. Network redundancy protection is a separate function associated with protection mechanisms rather than measurement. Accordingly B, C and D are correct.
Technical Deep Dive:
B, C and D are correct. iFIT works on real production flows rather than relying entirely on synthetic probing, which may not follow the same forwarding path as customer traffic. Ingress and downstream measurement points record packet counts and timestamps. Comparing samples across hops supports fault demarcation, while telemetry sends near-real-time records to iMaster NCE-IP for SLA visualization and proactive abnormality detection. Packet-loss rate is calculated as (Tx-Rx)/Tx, using corresponding observation windows and matched flows. Supported forwarding NP/ASIC functions implement flow identification and statistical operations at high throughput. The controller can use observed packet loss, delay or jitter to inform tunnel optimization or self-healing workflows. But iFIT itself does not provide the alternate link, replicated forwarding state or local FRR operation necessary for redundancy. Mechanisms such as TI-LFA, VPN FRR or hot standby provide protection; iFIT supplies the visibility required to detect and localize degradation.
#######################################################


NEW QUESTION # 31
In an EVPN L3VPNv4-over-SRv6 BE scenario, must P routers in a carrier network also support SRv6?

Answer: A

Explanation:
Huawei Reference Verification:
Huawei SRv6 Best Effort transports VPN services over native IPv6 reachability. An ingress PE can encapsulate the customer IPv4 packet using an outer IPv6 header whose destination identifies the remote egress service SID. Transit P routers forward the outer IPv6 packet by ordinary longest-prefix-match lookup toward the locator, without having to execute the service SID's endpoint behavior. The egress PE interprets its local SID and forwards the decapsulated customer traffic through the correct VPN instance. Therefore SRv6- capable PE endpoints are required but native SRv6 support on every P router is not mandatory.
Technical Deep Dive:
B is FALSE. An MPLS VPN transport typically requires P routers capable of swapping MPLS transport labels. SRv6 BE differs because ordinary IPv6 forwarding can carry the encapsulated service packet across the network. The ingress PE performs a customer VPN lookup, adds the outer IPv6 destination containing the egress service SID, and forwards into the IPv6 underlay. Each P router forwards according to its IPv6 FIB and need not understand End.DT4 or another egress service behavior. The egress PE receives the packet destined to its local SID, removes the appropriate transport encapsulation and performs the service VPN lookup. SRv6 support on transit routers remains useful for SRv6 TE, TI-LFA or other specialized transit behaviors but is not an inherent BE transport requirement. Underlay IPv6 reachability to the egress locator remains essential.
#######################################################


NEW QUESTION # 32
Which of the following statements is incorrect about the SR-TE tunnel configuration below?
[R1] interface tunnel1
[R1-Tunnel1] ip address unnumbered interface LoopBack0
[R1-Tunnel1] tunnel-protocol mpls te
[R1-Tunnel1] destination 3.3.3.3
[R1-Tunnel1] mpls te tunnel-id 1
[R1-Tunnel1] mpls te signal-protocol segment-routing
[R1-Tunnel1] mpls te pce delegate
Select all that apply.

Answer: B,D

Explanation:
Huawei Reference Verification:
Huawei's SR-TE tunnel CLI separates the transport tunnel type, the signaling protocol and the path- management mode. `tunnel-protocol mpls te` establishes an MPLS TE tunnel interface; `mpls te signal- protocol segment-routing` identifies Segment Routing as its signaling technology. `ip address unnumbered interface LoopBack0` borrows the Loopback0 address, and `mpls te tunnel-id 1` sets the tunnel identifier. The command `mpls te pce delegate` delegates LSP path management to the PCE through PCEP, rather than specifying a manually configured explicit path. Therefore the claims that SR is the tunnel protocol or that the path is manually specified are incorrect.
Technical Deep Dive:
C and D are incorrect. The displayed interface is a Tunnel1 MPLS TE tunnel whose address is borrowed from LoopBack0 and whose destination is 3.3.3.3. The tunnel ID is 1, unique as required within the applicable tunnel context. Segment Routing in this configuration is the signaling mechanism, not the value of the `tunnel- protocol` field. PCE delegation transfers supported LSP path computation/management to a Path Computation Element; it does not define a static explicit-path sequence locally. A manual explicit path would require its own explicit-path configuration and reference. PCEP is a TCP-based control protocol allowing the PCC to report LSP state and the PCE to deliver calculated routes or updates. An operational engineer can inspect the status with `display interface tunnel 1`, `display mpls te tunnel` and `display current-configuration interface Tunnel1`. The broader lesson is to read CLI keywords according to the configuration hierarchy rather than interpreting the presence of 'segment-routing' as a replacement of the underlying MPLS TE tunnel type.
#######################################################


NEW QUESTION # 33
The underlay layer of a telco cloud network can use a Layer 3 routing protocol, such as OSPF, IS-IS, or BGP, to provide IP connectivity between spine and leaf nodes.

Answer: B

Explanation:
Huawei Reference Verification:
Huawei's underlay/overlay architecture identifies the underlay as the physical network carrying overlay traffic. Routing protocols provide IP reachability between spine, leaf, and VTEP interfaces. The underlay can run OSPF or IS-IS as link-state protocols or BGP as a routed IP-fabric control plane. These distribute the reachable infrastructure networks and loopback addresses required for EVPN VXLAN tunnel operation. The overlay then supplies logical tenant/service connectivity while relying on the underlay to deliver encapsulated packets. This directly supports the statement that OSPF, IS-IS, or BGP can provide the spine-leaf Layer 3 underlay.
Technical Deep Dive:
A is TRUE. A routed spine-leaf fabric requires IP connectivity between infrastructure nodes and VXLAN tunnel endpoints. OSPF exchanges LSAs and calculates SPF paths. IS-IS performs link-state routing using LSPs and is commonly deployed in carrier networks. EBGP can provide a scalable routed leaf-to-spine design without extending one large IGP everywhere. When VXLAN is used, VTEP loopback addresses must resolve through an underlay route; an EVPN service route is unusable if its VTEP next hop cannot be reached. Equal- cost routes across multiple spines allow ECMP load distribution. The controller or routing processes compute network reachability, while the forwarding ASIC consults the installed FIB and implements the chosen next- hop/tunnel operations. Huawei VRP commands `display ospf peer`, `display isis peer`, `display bgp peer`,
`display ip routing-table`, and `display fib` establish whether underlay adjacency, reachability and forwarding state are healthy.
#######################################################


NEW QUESTION # 34
In the ONAP framework, which of the following closed-loop automation processes is used to respond to changing network and service conditions?

Answer: B

Explanation:
Exact Extract - Huawei Training Material (Network Orchestration Technologies Overview, p.34):
"Closed-loop automation: responds to network or service conditions without intervention through design, creation, collection, analysis, detection, release, and response." Huawei Reference Verification:
The Huawei ONAP module defines a closed-loop sequence beginning with design-time modeling and creation, followed by collection, analysis, detection, publication and response. ONAP uses SDC for service design and DCAE for operational data gathering and analysis. Collected telemetry and events are analyzed, resulting abnormalities or policy conditions are detected, the outcome is published to policy/orchestration components, and an authorized controller executes remediation. The curriculum diagram explicitly places Analysis before Detect. Thus the exact intended sequence is Design > Create > Collect > Analyze > Detect > Publish > Respond, corresponding to B.
Technical Deep Dive:
B is correct. ONAP separates design-time and run-time actions. During Design, network resources, service templates and closed-loop policies are defined. Create instantiates the specified service and its required network functions. Collect gathers service alarms, metrics and events, with DCAE providing collection infrastructure. Analyze evaluates observations for trends and anomalies; Detect identifies actionable conditions according to rules and policies. Publish distributes the relevant findings to policy and orchestration components, and Respond triggers measures such as service reconfiguration, VNF recovery or path adjustment. The exact order is important: analytical processing precedes identifying and publishing actionable conditions in this curriculum description. An incomplete answer omitting Design, such as A, cannot describe the full lifecycle; C and D change the expected analytic order. Closed-loop operation is designed to reduce the delay between fault observation and corrective action while preserving policy-based control.
#######################################################


NEW QUESTION # 35
......

The rapid development of information will not infringe on the learning value of our H35-831 study materials, because our customers will have the privilege to enjoy the free update for one year. You will receive the renewal of H35-831 study materials through the email. And our H35-831 study materials have three different version can meet your demands. Firstly, PDF version is easy to read and print. Secondly software version does not limit to the number of installed computers, and it simulates the Real H35-831 Exam environment, but it can only run on Windows operating system.

H35-831 Latest Examprep: https://www.validvce.com/H35-831-exam-collection.html