BONUS!!! ITDumpsKR H12-893_V1.0 시험 문제집 전체 버전을 무료로 다운로드하세요: https://drive.google.com/open?id=1RGYLxaYuab_1Cdq0e3K4HPqABIZ9CKlv
ITDumpsKR에서 출시한 Huawei 인증 H12-893_V1.0시험덤프는ITDumpsKR의 엘리트한 IT전문가들이 IT인증실제시험문제를 연구하여 제작한 최신버전 덤프입니다. 덤프는 실제시험의 모든 범위를 커버하고 있어 시험통과율이 거의 100%에 달합니다. 제일 빠른 시간내에 덤프에 있는 문제만 잘 이해하고 기억하신다면 시험패스는 문제없습니다.
| 주제 | 소개 |
|---|---|
| 주제 1 |
|
| 주제 2 |
|
| 주제 3 |
|
>> H12-893_V1.0최신버전 시험대비 공부자료 <<
Huawei H12-893_V1.0인증시험패스에는 많은 방법이 있습니다. 먼저 많은 시간을 투자하고 신경을 써서 전문적으로 과련 지식을 터득한다거나; 아니면 적은 시간투자와 적은 돈을 들여 ITDumpsKR의 인증시험덤프를 구매하는 방법 등이 있습니다.
질문 # 73
An enterprise builds a DC and deploys iMaster NCE-Fabric to automatically deliver network configurations. After the engineer manually deploys the underlay network and delivers overlay network configurations through iMaster NCE-Fabric, it is found that tenant hosts cannot access external networks. Which of the following is not a possible cause of this fault?
정답：B
설명：
In Huawei's CloudFabric Solution, iMaster NCE-Fabric automates overlay network (e.g., VXLAN) configuration, while the underlay network is manually deployed. Tenant hosts failing to access external networks indicate a connectivity issue, likely at the overlay-underlay boundary or security layer. Let's evaluate each option as a possible cause:
A . No return route is configured on the PE: This is a possible cause. The Provider Edge (PE) device (e.g., border leaf or router) must have a return route to the tenant's VXLAN network for external access. Without it, traffic from external networks cannot reach the DC. POSSIBLE CAUSE.
B . The engineer did not check whether the service loopback interface needs to be configured on the VXLAN network based on the switch model: This is a possible cause. Some Huawei switch models (e.g., CE series) require a service loopback interface as the VTEP source IP. If omitted or misconfigured based on the model, external connectivity fails. POSSIBLE CAUSE.
C . No firewall security policy is configured when host traffic passes through the firewall: This is a possible cause. If a firewall is in the path (e.g., between tenant VPC and external network), a missing security policy (e.g., allowing outbound traffic) blocks access. POSSIBLE CAUSE.
D . The MAC address of the NVE interface on the VXLAN network is not manually specified: This is not a possible cause. The Network Virtualization Edge (NVE) interface in VXLAN does not require a manually specified MAC address; it uses the switch's system MAC or auto-generates one. iMaster NCE-Fabric typically handles this automatically, and manual specification is neither required nor a common fault point for external access issues. NOT A POSSIBLE CAUSE.
Thus, D is not a possible cause of the fault.
질문 # 74
When an SDN controller cluster is deployed in Huawei CloudFabric Solution, which of the following network planes are divided based on carried services? (Select All that Apply)
정답：A,B,C
설명：
In Huawei's CloudFabric Solution, the iMaster NCE-Fabric SDN controller cluster separates network planes based on carried services to ensure scalability and security. Let's evaluate each option:
A . BGP microservice plane: This is not a standard plane in Huawei's SDN architecture. BGP is used in the underlay/overlay but not defined as a separate microservice plane for the controller. FALSE.
B . Southbound service plane: This is true. The southbound plane carries configuration and control data to network devices (e.g., via NETCONF, BGP-EVPN), a critical service plane in SDN. TRUE.
C . Northbound management plane: This is true. The northbound plane provides APIs for management applications and orchestration (e.g., OpenStack integration), handling service requests. TRUE.
D . Internal communication plane: This is true. This plane facilitates communication between controller cluster nodes for synchronization and high availability. TRUE.
Thus, B (Southbound service plane), C (Northbound management plane), and D (Internal communication plane) are the network planes divided based on carried services.
질문 # 75
Which of the following can be used as the conditions for microsegmentation to divide EPGs? (Select All that Apply)
정답：A,B,C,D
설명：
Microsegmentation in Huawei's data center networks (e.g., CloudFabric with SDN) divides Endpoint Groups (EPGs) to enforce fine-grained security policies. EPGs group endpoints (e.g., VMs) based on attributes. Let's evaluate each option:
A . Operating system: This is true. The OS type (e.g., Linux, Windows) can be used to segment EPGs, enabling policy enforcement based on OS-specific security needs. TRUE.
B . VM name: This is true. VM names can be used as identifiers for microsegmentation, allowing policies to target specific VMs. TRUE.
C . IP address: This is true. IP addresses are commonly used to define EPG boundaries, especially for network-based segmentation. TRUE.
D . MAC address: This is true. MAC addresses can segment EPGs, particularly for Layer 2-based policies or device-specific isolation. TRUE.
All options A, B, C, and D are valid conditions for microsegmentation to divide EPGs in Huawei's implementation.
질문 # 76
The figure shows an incomplete VXLAN packet format.
Which of the following positions should the VXLAN header be inserted into so that the packet format is complete?
정답：B
설명：
VXLAN (Virtual Extensible LAN) is a tunneling protocol that encapsulates Layer 2 Ethernet frames within UDP packets to extend VLANs across Layer 3 networks, commonly used in Huawei's CloudFabric data center solutions. The provided figure illustrates an incomplete VXLAN packet format with the following sequence:
Outer Ethernet Header (Position 1): Encapsulates the packet for transport over the physical network.
Outer IP Header (Position 2): Defines the source and destination IP addresses for the tunnel endpoints.
UDP Header (Position 3): Carries the VXLAN traffic over UDP port 4789.
Inner Ethernet Header (Position 4): The original Layer 2 frame from the VM or endpoint.
Inner IP Header (Position 5): The original IP header of the encapsulated payload.
Payload (Position 6): The data being transported.
The VXLAN header, which includes a 24-bit VXLAN Network Identifier (VNI) to identify the virtual network, must be inserted to complete the encapsulation. In a standard VXLAN packet format:
The VXLAN header follows the UDP header and precedes the inner Ethernet header. This is because the VXLAN header is part of the encapsulation layer, providing the VNI to map the inner frame to the correct overlay network.
The sequence is: Outer Ethernet Header → Outer IP Header → UDP Header → VXLAN Header → Inner Ethernet Header → Inner IP Header → Payload.
In the figure, the positions are numbered as follows:
1: Outer Ethernet Header
2: Outer IP Header
3: UDP Header
4: Inner Ethernet Header
The VXLAN header should be inserted after the UDP header (Position 3) and before the Inner Ethernet Header (Position 4). However, the question asks for the position where the VXLAN header should be "inserted into," implying the point of insertion relative to the existing headers. Since the inner Ethernet header (Position 4) is where the encapsulated data begins, the VXLAN header must be placed just before it, which corresponds to inserting it at the transition from the UDP header to the inner headers. Thus, the correct position is D (2) if interpreted as the logical insertion point after the UDP header, but based on the numbering, it aligns with the need to place it before Position 4. Correcting for the figure's intent, the VXLAN header insertion logically occurs at the boundary before Position 4, but the options suggest a mislabeling. Given standard VXLAN documentation, the VXLAN header follows UDP (Position 3), and the closest insertion point before the inner headers is misinterpreted in numbering. Re-evaluating the figure, Position 2 (after Outer IP Header) is incorrect, and Position 3 (after UDP) is not listed separately. The correct technical insertion is after UDP, but the best fit per options is D (2) as a misnumbered reference to the UDP-to-inner transition. However, standard correction yields after UDP (not directly an option), but strictly, it's after 3. Given options, D (2) is the intended answer based on misaligned numbering.
Corrected answer: After re-evaluating the standard VXLAN packet structure and the figure's
질문 # 77
Which of the following is not included in the physical architecture of a server?
정답：B
설명：
The physical architecture of a server refers to the tangible and low-level components that constitute the server itself, distinct from logical or software layers. Let's evaluate each option:
A . Application: Applications are software running on top of an operating system or virtual machine, not part of the server's physical architecture. They belong to the logical or user layer, not the physical structure. Not Included.
B . VMmonitor (Hypervisor): Assuming "VMmonitor" refers to a hypervisor (e.g., KVM or Xen), it's a software layer, but in Type-1 hypervisor scenarios, it runs directly on hardware, managing VMs. In Huawei's context, it's considered part of the server's operational architecture when deployed physically. Included.
C . OS (Operating System): The OS (e.g., Linux, Windows) runs directly on server hardware or within a VM. In bare-metal servers, it's a core component of the physical deployment. Included.
D . Hardware: Hardware (e.g., CPU, RAM, NICs, disks) is the foundational physical architecture of a server, providing the physical resources for all operations. Included.
Thus, A (Application) is not part of the physical architecture, as it's a higher-level software entity, not a physical component.
질문 # 78
......
Huawei H12-893_V1.0인증시험은 전문적인 관련지식을 테스트하는 인증시험입니다. ITDumpsKR는 여러분이Huawei H12-893_V1.0인증시험을 통과할 수 잇도록 도와주는 사이트입니다. 여러분은 응시 전 저희의 문제와 답만 잘 장악한다면 빠른 시일 내에 많은 성과 가 있을 것입니다.
H12-893_V1.0시험대비 공부하기: https://www.itdumpskr.com/H12-893_V1.0-exam.html
참고: ITDumpsKR에서 Google Drive로 공유하는 무료 2026 Huawei H12-893_V1.0 시험 문제집이 있습니다: https://drive.google.com/open?id=1RGYLxaYuab_1Cdq0e3K4HPqABIZ9CKlv